Large, rapid landslides are a global hazard that can occur in remote, mountainous areas. Eyewitness reports of landslides and satellite imagery can often be limited or delayed, particularly during inclement weather. However, landslide-generated seismic and infrasound (low-frequency atmospheric sound) waves can be remotely detected in near real-time. This information can significantly expedite characterization and possible landslide response activities. Here, we highlight these capabilities using a 6.1 million m3 ice-rock avalanche in Denali National Park and Preserve (Alaska). This event was detected via a landslide-specific seismic location and volume estimation algorithm deployed in Alaska, and-notably-by standard earthquake monitoring systems. Following rapid detection of this event, we combined its seismic and infrasound data set with optical, synthetic aperture radar, and oblique aerial imagery, multitemporal digital elevation models, and a numerical flow model to reconstruct its failure timeline and dynamics. We apply array processing to infrasound signals traveling >250 km and find that two precursory events occurred minutes prior to the main failure. We use long-period seismic signals to infer the force exerted by the landslide on the Earth and constrain the rheological parameters of our numerical flow simulation with this result and deposit morphology. The main failure produced a steeply dipping impulsive initial downward force and reached speeds exceeding 60 m/s. This impulsive force generated relatively strong seismic body waves, which contributed to the earthquake system detection. This large, remote Alaska landslide underscores the key value of seismic and infrasound analysis for rapid landslide assessment and motivates efforts to further operationalize these approaches.

The Barry Landslide, located in Barry Arm of Prince William Sound, Alaska, poses a major hazard due to its steep, unstable slopes, and the potential for a massive landslide-generated tsunami. With an estimated volume of 500–700 million cubic meters, the Barry Landslide could trigger highly destructive waves. In this study, we focus on seismic signals from the Barry Landslide, which are critical for providing timely tsunami warnings. Since the summer of 2020, the region has been instrumented to monitor the landslide, but the seismic record is complicated by the presence of nearby glaciers and frequent regional earthquakes. Among these signals, we analyze a specific class of short-duration, high-frequency seismic events that exhibit strong seasonal variability, increasing in rate from late summer to midwinter before ceasing abruptly in late winter or early spring. Our analysis suggests that the source of these signals is likely near or beneath Cascade Glacier, adjacent to the landslide, rather than within the landslide mass itself. We apply detection algorithms to construct a time history for this signal type, which we then compare with environmental factors like precipitation, temperature, and slope displacement data from ground-based radar and remote sensing. Correlations indicate that these seismic events may be driven by seasonal hydrological changes, particularly the freeze-up of subglacial water pathways. Although these events are not directly linked to landslide motion, they serve as indirect markers of subsurface hydrological conditions that influence slope stability. Our findings highlight the complex interplay between glaciers, groundwater, and landslide dynamics, emphasizing the need for multiparameter monitoring to assess evolving geohazards in the region.

Pulse-like infrasound accompanying volcanic phenomena sometimes suggests interaction with water at the crater. We focus on pulse-like infrasound observed at Semisopochnoi Island in the Aleutian Arc, Alaska, during the phreatomagmatic activity on 13 July 2021. Overflight observations confirmed a small, ephemeral water lake on the crater floor in June 2021. We examined temporal variations in pulse-like infrasound activity, seismoacoustic amplitudes, and spectral characteristics. Pulse-like infrasound activity gradually became intermittent and waned at the end of the day. Seismic-infrasonic amplitude ratio decreased, while the infrasound frequency index increased with time. These results suggest less interaction with water due to drying out of the vent. Satellite observations also show increased ground surface temperatures inside the crater from 13 to 14 July. Numerical simulation suggests a significant topographic effect on the waveform and spectrum of the pulse-like infrasound, which should be considered before interpreting the source process.

Volcano seismicity is often detected and classified based on its spectral properties. However, the wide variety of volcano seismic signals and increasing amounts of data make accurate, consistent, and efficient detection and classification challenging. Machine learning (ML) has proven very effective at detecting and classifying tectonic seismicity, particularly using Convolutional Neural Networks (CNNs) and leveraging labeled datasets from regional seismic networks. Progress has been made applying ML to volcano seismicity, but efforts have typically been focused on a single volcano and are often hampered by the limited availability of training data. We build on the method of Tan et al. [2024] (10.1029/2024JB029194) to generalize a spectrogram-based CNN termed the VOlcano Infrasound and Seismic Spectrogram Neural Network (VOISS-Net) to detect and classify volcano seismicity at any volcano. We use a diverse training dataset of over 270,000 spectrograms from multiple volcanoes: Pavlof, Semisopochnoi, Tanaga, Takawangha, and Redoubt volcanoes\replaced (Alaska, USA); Mt. Etna (Italy); and Kīlauea, Hawai`i (USA). These volcanoes present a wide range of volcano seismic signals, source-receiver distances, and eruption styles. Our generalized VOISS-Net model achieves an accuracy of 87 % on the test set. We apply this model to continuous data from several volcanoes and eruptions included within and outside our training set, and find that multiple types of tremor, explosions, earthquakes, long-period events, and noise are successfully detected and classified. The model occasionally confuses transient signals such as earthquakes and explosions and misclassifies seismicity not included in the training dataset (e.g. teleseismic earthquakes). We envision the generalized VOISS-Net model to be applicable in both research and operational volcano monitoring settings.

Alaska's coastal communities face growing landslide hazards owing to glacier retreat and extreme weather intensified by the warming climate, yet hazard monitoring remains challenging. As part of ongoing experimental monitoring in Prince William Sound, we detected three large landslides (0.5-2.3 M m3) at Surprise Inlet on 20 September 2024, within the span of an hour. These events were identified in near real-time through seismic data and later confirmed using satellite imagery, tidal records, and infrasound. The landslides generated a modest tsunami, and a 4 cm wave was recorded by a tide gauge 18 km away, marking the first recorded landslide to reach water since monitoring began in this region in 2021. Here, we examine the detection and interpretation of these landslides using multiple data sources and modeling. We demonstrate the effectiveness of this regional seismic monitoring system and show how complementary instrumentation, where available, can enhance detection capabilities.

The 2018-2023 phreatomagmatic eruptions at Semisopochnoi Island, Alaska produced abundant long-period (LP) seismicity, harmonic and broadband tremor, and explosion signals over several well-monitored periods of eruption and quiescence. The corresponding dataset provides an excellent opportunity to investigate precursory and syn-eruptive geophysical signals of long-lived phreatomagmatic eruptions using multiparameter observations. We generated explosion and LP event catalogs through novel implementations of the REDPy (HotovecEllis, 2024) repeating event detector in mid-2021 following a network upgrade and the onset of a new phase of the eruption. The hundreds of detected explosions show a high degree of infrasound waveform similarity over more than a year, indicating a repeating source mechanism likely associated with explosive magma-water interaction. The seismic LP catalog shows that events began over a month prior to renewed explosive activity at the beginning of August 2021, and that lower frequency index (FI) LPs were generated in the week prior to the onset of explosions. We applied a recently developed machine learning tool (VOISS-Net, Tan et al., 2024) to catalog abundant broadband and harmonic seismic tremor recorded before and during the renewed explosive activity, along with LPs and explosions. The tremor catalogs complement the LP and explosion catalogs by filling out the seismic sequence with the dominant signal types. Together, these catalogs reveal a seismic sequence of renewed unrest that started with several weeks of LP events, followed by LPs with lower FI values and harmonic tremor in the days prior to explosive activity, and finally the onset of discrete explosions and broadband eruption tremor. We interpret this sequence as the ascent of a new pulse of magma that first interacted with the hydrothermal/groundwater system to produce LPs, followed by harmonic tremor, and that ultimately drove explosive magma-water interactions and periods of continuous ash emissions. The 2021 seismic sequence, in combination with long-term records of satellite SO2 emissions, deformation from interferometric synthetic aperture radar (InSAR) analysis, ash sample analysis, infrasound, and volcano tectonic seismicity, allows us to interpret the entire 9-year period of unrest and eruption that began with an intrusion and earthquake swarm in 2014.

The 2022 Mauna Loa eruption began on November 27 23:21 HST (November 28 9:21 UTC) at the summit, based on the onset of seismic tremor and visual observations of nighttime incandescence from lava viewed by webcameras. Continued visual observations noted early southwestward migration of the summit flows followed by dike propagation and new fissures on the northeast rift zone in the early hours of November 28th HST. Northeast rift zone activity subsequently settled into persistent activity primarily from Fissure 3 (located about 7 km from the Summit) until the eruption stagnated by December 9th HST.This contribution provides a detailed retrospective assessment of the performance of four Hawaiian Volcano Observatory (HVO) infrasound arrays (AIND, AHUD, MENE, SHEEP) and an International Monitoring System array operated by the University of Hawaii Infrasound (I59US) data during the onset and progression of the eruption. We use results from a standard least-squares beamforming algorithm which is widely used for infrasound processing across the USGS Volcano Science Center and compare other multidisciplinary observations such as visual and seismic amplitude.We find that that the standard array processing approach performed adequately as a real-time assessment tool with high correlation back-azimuth computations in reasonable agreement with visual observations. High winds associated with storms impacted the quality of our results, particularly toward the end of the eruption when infrasound signals were comparably small. It was possible to distinguish between summit and rift fissure activity using the three long-term arrays operated by HVO, despite the large source to receiver distance. The SHEEP array (on the south flank of Mauna Kea) was established in response to the Mauna Loa eruption and only recorded the waning phase of the eruption. Regardless, the new array should further improve azimuthal coverage for future Mauna Loa eruptive activity.

During an effusive eruption crisis the initial advance of a lava flow is typically the primary focus of model forecasts and hazard management efforts. Flow branching and lateral expansion of lava flows can pose significant dangers within evolving flow fields throughout the duration of an eruption and are an underappreciated hazard. We use field monitoring, infrasound, time lapse imagery, and lidar data collected during the 2018 lower East Rift Zone eruption of Kīlauea (Hawai‘i) to track the origins, progression, and implications of a flow branching event caused by catastrophic levee failure. Our analyses show that surges in effusion rate, rheologic transitions between pāhoehoe and ‘a‘ā flow regimes, slope-breaks, pre-existing topographic highs, and the structure of perched levee walls all played a role in the failure of the levee and subsequent re-routing of the lava flow. Failure of perched lava structures leads to an acutely hazardous situation because lava impounded by the structure can rapidly inundate the landscape. This is the first time a levee failure event has been observed in such detail with numerous monitoring techniques; this unprecedented level of observation provides quantifiable insights into levee failure processes that have important implications for hazard mitigation and an improved understanding of lava flow emplacement dynamics

First posted April 9, 2024 For additional information, contact: Alaska Volcano ObservatoryU.S. Geological Survey4210 University DriveAnchorage, AK 99508 The Alaska Volcano Observatory responded to eruptions, volcanic unrest or suspected unrest, increased seismicity, and other significant activity at nine volcanic centers in Alaska in 2020. The most notable volcanic activity in 2020 was an eruption of Shishaldin Volcano, which produced lava flows, lahars, and ash. Mount Cleveland had one small ash-producing eruption in June but was quiet thereafter. Other activity documented in 2020 consisted of elevated seismicity at the volcanoes Mount Veniaminof, Pavlof Volcano, Makushin Volcano, Atka volcanic complex (Korovin Volcano), Great Sitkin Volcano, and Semisopochnoi Island. Finally, the resuspension of ash deposited during the 1912 Novarupta-Katmai eruption was documented on three occasions.

First posted April 9, 2024 For additional information, contact: Alaska Volcano ObservatoryU.S. Geological Survey4210 University DriveAnchorage, AK 99508 In 2021, the Alaska Volcano Observatory responded to eruptions, volcanic unrest or suspected unrest, increased seismicity, and other significant activity at 15 volcanic centers in Alaska and the Commonwealth of the Northern Mariana Islands. Eruptive activity in Alaska consisted of repeated small, ash-producing, phreatomagmatic explosions from Mount Young on Semisopochnoi Island; an explosion at Great Sitkin Volcano followed by the eruption of a thick lava flow that filled and overflowed the summit crater; weak explosive activity and the eruption of small, channelized flows at Pavlof Volcano; and a short-lived eruption at Mount Veniaminof that produced ash emissions from an intracaldera cone, as well as lava flows confined to a melt pit in the ice mantling the cone's flank. Mount Cleveland had a period of unrest, but no eruptive activity took place there. Anomalous seismicity was also detected at Atka volcanic complex, Mount Gareloi, and Davidof volcano. New warm springs opened and deposited mud at the summit and north base of Shrub mud volcano. Other activity of note in Alaska consisted of large ice and rock avalanches at Iliamna Volcano and Mount Spurr, ash resuspension events at Mount Katmai and Aniakchak Crater, and anomalous deformation at Mount Okmok that was consistent with a shallow intrusion of magma. In the Commonwealth of the Northern Marianas Islands, a brief, ash-producing eruption occurred at Mount Pagan.

The Alaska Volcano Observatory (AVO) uses multidisciplinary data to monitor and study dozens of active and potentially active volcanoes. Here, we provide an overview of internally and externally generated data types, tools and resources used in their management, and challenges faced. Data sources include the following: (1) a multiparameter (seismic, infrasound, GNSS, web cameras) ground-based monitoring network that spans 3000 km and transmits data in real time; (2) a variety of satellite-borne sensors that provide information about surface change and volcanic emissions; (3) geologic and gas field campaigns; and (4) other external data products that provide situation awareness. Each data type requires distinct acquisition, processing, storage, visualization, and archiving approaches. AVO uses a variety of externally and internally developed tools to handle individual data types as well as multidisciplinary volcanological data. A primary tool is the Geologic Database of Information on Volcanoes in Alaska (GeoDIVA), which stores detailed, searchable information on more than 140 volcanoes and over 1000 eruptions and unrest events, including images, eruption descriptions, and geologic station and sample data, metadata, and analyses. It interacts with other internal tools that store monitoring reports and other operational records. Additional data management resources used by AVO assist with alarms and alerts, state-of-health monitoring, and multiparameter visualization. Requirements for 24/7 accessibility, the ever-expanding portfolio of data, and transitioning new tools from development to operations are all challenges faced by AVO and other volcano observatories. AVO strives to meet FAIR data practices and ensure that data are available to national and international community efforts using external repositories as well as those hosted by AVO and its parent institutions.

SUMMARY Infrasound sensors are deployed in a variety of spatial configurations and scales for geophysical monitoring, including networks of single sensors and networks of multisensor infrasound arrays. Infrasound signal detection strategies exploiting these data commonly make use of intersensor correlation and coherence (array processing, multichannel correlation); network-based tracking of signal features (e.g. reverse time migration); or a combination of these such as backazimuth cross-bearings for multiple arrays. Single-sensor trace-based denoising techniques offer significant potential to improve all of these various infrasound data processing strategies, but have not previously been investigated in detail. Single-sensor denoising represents a pre-processing step that could reduce the effects of ambient infrasound and wind noise in infrasound signal association and location workflows. We systematically investigate the utility of a range of single-sensor denoising methods for infrasound data processing, including noise gating, non-negative matrix factorization, and data-adaptive Wiener filtering. For the data testbed, we use the relatively dense regional infrasound network in Alaska, which records a high rate of volcanic eruptions with signals varying in power, duration, and waveform and spectral character. We primarily use data from the 2016–2017 Bogoslof volcanic eruption, which included multiple explosions, and synthetics. The Bogoslof volcanic sequence provides an opportunity to investigate regional infrasound detection, association, and location for a set of real sources with varying source spectra subject to anisotropic atmospheric propagation and varying noise levels (both incoherent wind noise and coherent ambient infrasound, primarily microbaroms). We illustrate the advantages and disadvantages of the different denoising methods in categories such as event detection, waveform distortion, the need for manual data labelling, and computational cost. For all approaches, denoising generally performs better for signals with higher signal-to-noise ratios and with less spectral and temporal overlap between signals and noise. Microbaroms are the most globally pervasive and repetitive coherent ambient infrasound noise source, with such noise often referred to as clutter or interference. We find that denoising offers significant potential for microbarom clutter reduction. Single-channel denoising of microbaroms prior to standard array processing enhances both the quantity and bandwidth of detectable volcanic events. We find that reduction of incoherent wind noise is more challenging using the denoising methods we investigate; thus, station hardware (wind noise reduction systems) and site selection remain critical and cannot be replaced by currently available digital denoising methodologies. Overall, we find that adding single-channel denoising as a component in the processing workflow can benefit a variety of infrasound signal detection, association, and location schemes. The denoising methods can also isolate the noise itself, with utility in statistically characterizing ambient infrasound noise.

We present the transverse coherence minimization method (TCM)—an approach to estimate the back-azimuth of infrasound signals that are recorded on an infrasound microphone and a colocated three-component seismometer. Accurate back-azimuth information is important for a variety of monitoring efforts, but it is currently only available for infrasound arrays and for seismoacoustic sensor pairs separated by 10 s of meters. Our TCM method allows for the analysis of colocated sensor pairs, sensors located within a few meters of each other, which may extend the capabilities of existing seismoacoustic networks and supplement operating infrasound arrays. This approach minimizes the coherence of the transverse component of seismic displacement with the infrasound wave to estimate the infrasound back-azimuth. After developing an analytical model, we investigate seismoacoustic signals from the August 2012 Humming Roadrunner experiment and the 26 May 2021 eruption of Great Sitkin Volcano, Alaska, U.S.A., at the ranges of 6.5–185 km from the source. We discuss back-azimuth estimates and potential sources of deviation (1°–15°), such as local terrain effects or deviation from common analytical models. This practical method complements existing seismoacoustic tools and may be suitable for routine application to signals of interest.

Real-time monitoring is crucial to assess hazards and mitigate risks of sustained volcanic eruptions that last hours to months or more. Sustained eruptions have been shown to produce a low frequency (infrasonic) form of jet noise. We analyze the lava fountaining at fissure 8 during the 2018 Lower East Rift Zone eruption of Kīlauea volcano, Hawaii, and connect changes in fountain properties with recorded infrasound signals from an array about 500 m from the fountain using jet noise scaling laws and visual imagery. Video footage from the eruption reveals a change in lava fountain dynamics from a tall, distinct fountain at the beginning of June to a low fountain with a turbulent, out-pouring lava pond surrounded by a tephra cone by mid-June. During mid-June, the sound pressure level reaches a maximum, and peak frequency drops. We develop a model that uses jet noise scaling relationships to estimate changes in volcanic jet diameter and jet velocity from infrasound sound pressure levels and peak frequencies. The results of this model indicate a decrease in velocity in mid-June which coincides with the decrease in fountain height. Furthermore, the model results suggest an increase in jet diameter, which can be explained by the larger width of the fountain that resembles a turbulent lava pond compared to the distinct fountain at the beginning of June. The agreement between the infrasound-derived and visually observed changes in fountain dynamics suggests that jet noise scaling relationships can be used to monitor lava fountain dynamics using infrasound recordings.

The 2018 eruption of Kīlauea Volcano was a dynamic event involving explosions, collapses, and fountaining at multiple vents spread over tens of kilometers. The permanent infrasound network operated by the USGS Hawaiian Volcano Observatory (HVO) was well prepared to observe the collapse of the summit, and additional deployments permitted infrasound observations during fissuring in the lower East Rift Zone (LERZ). We provide a summary of infrasound observations, including lava lake spattering, collapses, explosions, rockfall, and lava fountaining, using seismicity and tilt at times to help constrain our interpretations. At the summit of Kīlauea Volcano, we document the process of partial caldera collapse and examine a set of “proto-collapse” events that precede the widely observed events but share many of the same qualities as the larger collapses. For the initial twelve collapse events, we compare the timing of collapse onset to other observations and illustrate the repeatable characteristics of the recorded waveforms and infrasound characteristics associated with each episode of caldera collapse. In the LERZ, we match the acoustic signals with visual observations, including fissure migration, explosions near fissures, and littoral explosions. Lastly, we document and discuss the performance of infrasound alarms during the 2018 Kīlauea eruption. In general, alarming became successful in detecting collapse events at the summit of the volcano after tuning and became a key discriminant in the initial determination of collapse events, especially when visual observations were not available.

The 15 January 2022 climactic eruption of Hunga volcano, Tonga, produced an explosion in the atmosphere of a size that has not been documented in the modern geophysical record. The event generated a broad range of atmospheric waves observed globally by various ground-based and spaceborne instrumentation networks. Most prominent was the surface-guided Lamb wave (≲0.01 hertz), which we observed propagating for four (plus three antipodal) passages around Earth over 6 days. As measured by the Lamb wave amplitudes, the climactic Hunga explosion was comparable in size to that of the 1883 Krakatau eruption. The Hunga eruption produced remarkable globally detected infrasound (0.01 to 20 hertz), long-range (~10,000 kilometers) audible sound, and ionospheric perturbations. Seismometers worldwide recorded pure seismic and air-to-ground coupled waves. Air-to-sea coupling likely contributed to fast-arriving tsunamis. Here, we highlight exceptional observations of the atmospheric waves.

Infrasound data are routinely used to detect and locate volcanic and other explosions, using both arrays and single sensor networks. However, at local distances (<15 km) topography often complicates acoustic propagation, resulting in inaccurate acoustic travel times leading to biased source locations when assuming straight-line propagation. Here we present a new method, termed Reverse Time Migration-Finite-Difference Time Domain (RTM-FDTD), that integrates numerical modeling into the standard RTM back-projection process. Travel time information is computed across the entire potential source grid via FDTD modeling to incorporate the effects of topography. The waveforms are then back-projected and stacked at each grid point, with the stack maximum corresponding to the likely source. We apply our method to three volcanoes with different network configurations, source-receiver distances, and topography. At Yasur Volcano, Vanuatu, RTM-FDTD locates explosions within ∼20 m of the source and differentiates between multiple vents. RTM-FDTD produces a more accurate location for the two Yasur subcraters than standard RTM and doubles the number of detected events. At Sakurajima Volcano, Japan, RTM-FDTD locates the source within 50 m of the active vent despite notable topographic blocking. The RTM-FDTD location is similar to that from the Time Reversal Mirror method, but is more computationally efficient. Lastly, at Shishaldin Volcano, Alaska, RTM and RTM-FDTD both produce realistic source locations (<50 m) for ground-coupled airwaves recorded on a four-station seismic network. We show that RTM is an effective method to detect and locate infrasonic sources across a variety of scenarios, and by integrating numerical modeling, RTM-FDTD produces more accurate source locations and increases the detection capability.