In ASDEX Upgrade, the propagation of cold pulses induced by type-I edge localized modes (ELMs) is studied using electron cyclotron emission measurements, in a dataset of plasmas with moderate triangularity. It is found that the edge safety factor or the plasma current are the main determining parameters for the inward penetration of the Te perturbations. With increasing plasma current the ELM penetration is more shallow in spite of the stronger ELMs. Estimates of the heat pulse diffusivity show that the corresponding transport is too large to be representative of the inter-ELM phase. Ergodization of the plasma edge during ELMs is a possible explanation for the observed properties of the cold pulse propagation, which is qualitatively consistent with non-linear magneto-hydro-dynamic simulations.

Plasma tomography consists of reconstructing a two-dimensional radiation profile of a poloidal cross section of a fusion device based on line-integrated measurements along several lines of sight. The reconstruction process is computationally intensive, and in practice, only a few reconstructions are usually computed per pulse. In this work, we trained a deep neural network based on a large collection of sample tomograms that have been produced at JET over several years. Once trained, the network is able to reproduce those results with high accuracy. More importantly, it can compute all the tomographic reconstructions for a given pulse in just a few seconds. This makes it possible to visualize several phenomena—such as plasma heating, disruptions, and impurity transport—over the course of the entire pulse.

This paper presents the first application to real JET data of the new equilibrium code NICE which enables the consistent resolution of the inverse equilibrium reconstruction problem in the framework of non-linear free-boundary equilibrium coupled to the Stokes model equation for polarimetry. The conducted numerical experiments enable first of all to validate NICE by comparing it to the well-established EFIT code on 4 selected high performance shots. Secondly the results indicate that the fit to polarimetry measurements clearly benefits from the use of Stokes vector measurements compared to the classical case of Faraday measurements, and that the reconstructed p' and ff' profiles are better constrained with smaller error bars and are closer to the profiles reconstructed by EFTM, the EFIT JET code using internal MSE constraints.

Principal research on energy from thermonuclear fusion uses Deuterium-Tritium plasmas magnetically trapped in toroidal devices. As major scientific problem for an economic (i.e., really feasible) reactor, we must understand how to lead strongly heated plasmas to sustain a high fusion gain while large fraction of current is self-produced via the presence of strong pressure gradient. To suppress turbulent eddies that impair thermal insulation and pressure tight of the plasma, current drive (CD) is necessary. However, tools envisaged so far in ITER (International Thermonuclear Experiment Rector) are unable accomplishing this task that requires efficiently and flexibly matching the natural current profiles of plasma. Consequently, viability of a thermonuclear reactor should be problematic. Multi-megawatt radio-frequency (RF) power coupled to plasma would produce the necessary CD, but modelling results based on previous understanding found difficult the extrapolation of this CD concept to reactor conditions of high temperature plasma, and greater flexibility of method would also be required. Here we present new model results based on standard quasilinear (QL) theory that allow establish conditions to drive efficiently and flexibly the RF-driven current at large radii of the plasma column, as necessary for the goal of a reactor.

Progress in understanding lower hybrid current drive (LHCD) at high density has been made through experiments and modeling, which is encouraging given the need for an efficient off-axis current profile control technique in burning plasma. By reducing the wall recycling of neutrals, the edge temperature is increased and the effect of parametric instability (PI) and collisional absorption (CA) is reduced, which is beneficial for increasing the current drive efficiency. Strong single pass absorption is preferred to prevent CA and high LH operating frequency is essential for wave propagation to the core region at high density, presumably to mitigate the effect of PI. The dimensionless parameter that characterizes LH wave accessibility and wave refraction for the experiments in this joint study is shown to bracket the region in parameter space where ITER LHCD experiments will operate in the steady state scenario phase. Further joint experiments and cross modeling are necessary to understand the LHCD physics in weak damping regimes which would increase confidence in predictions for ITER where the absorption is expected to be strong.

Experiments on runaway electrons have been performed for the determination of the critical electric field for runaway generation. A large database of post-disruption runaway beams has been analyzed in order to identify linear dynamical models for new position and current runaway beam controllers, and experiments of electron cyclotron assisted plasma start-up have shown the presence of runaway electrons also below the expected electric field threshold, indicating that the radio-frequency power acts as seeding for fast electrons. A linear micro-stability analysis of neon-doped pulses has been carried out to investigate the mechanisms leading to the observed density peaking. A study of the ion drift effects on the MARFE instability has been performed and the peaking of density profile in the high density regime has been well reproduced using a thermo-diffusive pinch in the particle transport equation. The study of the density limit performed in the past has been extended towards lower values of toroidal magnetic field and plasma current. The analysis of the linear stability of the 2/1 tearing mode observed in high density plasmas has highlighted a destabilization with increasing peaking of the current profile during the density ramp-up, while the final phase of the mode temporal evolution is characterized by limit cycles on the amplitude/frequency plane. A liquid lithium limiter with thermal load capability up to 10 MW m−2 has been tested. The pulse duration has been extended up to 4.5 s and elongated configurations have been obtained for 3.5 s, with the X-point just outside the plasma chamber. A W/Fe sample has been exposed in the scrape-off layer in order to study the sputtering of Fe and the W enrichment of the surface layer. Dusts have been collected and analyzed, showing that the metallic population exhibits a high fraction of magnetic grains. A new diagnostic for in-flight runaway electron studies has allowed the image and the visible/infrared spectrum of the forward and backward synchrotron radiation to be provided simultaneously. A fast infrared camera for thermo-graphic analysis has provided the pattern of the toroidal limiter heating by disruption heat loads, and a triple-GEM detector has been tested for soft x-ray diagnostics. The collective Thomson scattering diagnostic has been upgraded and used for investigations on parametric decay instability excitation by electron cyclotron beams correlated with magnetic islands, and new capabilities of the Cherenkov probe have been explored in the presence of beta-induced Alfvén eigenmodes associated to high amplitude magnetic islands.

The active control of the radial current density profile is one of the major issues of thermonuclear fusion energy research based on magnetic confinement. The lower hybrid current drive could in principle be used as an efficient tool. However, previous understanding considered the electron temperature envisaged in a reactor at the plasma periphery too large to allow penetration of the coupled radio frequency (RF) power due to strong Landau damping. In this work, we present new numerical results based on quasilinear theory, showing that the injection of power spectra with different n // widths of the main lobe produce an RF-driven current density profile spanning most of the outer radial half of the plasma ( n // is the refractive index in a parallel direction to the confinement magnetic field). Plasma kinetic profiles envisaged for the DEMO reactor are used as references. We demonstrate the robustness of the modeling results concerning the key role of the spectral width in determining the lower hybrid-driven current density profile. Scans of plasma parameters are extensively carried out with the aim of excluding the possibility that any artefact of the utilised numerical modeling would produce any novelty. We neglect here the parasitic effect of spectral broadening produced by linear scattering due to plasma density fluctuations, which mainly occurs for low magnetic field devices. This effect will be analyzed in other work that completes the report on the present breakthrough.

Lower hybrid current drive (LHCD) is an effective tool to achieve high confinement (H-mode) plasma in EAST. To utilize LHCD for accessing H-mode plasma, efforts have been made to improve LHW (lower hybrid wave)-plasma coupling and current drive capability at high density. Improved LHW-plasma coupling by means of local gas puffing and gas puffing from the electron side is routinely used during EAST operation with LHCD. High density experiments suggest that low recycling and high LH frequency are preferred for LHCD experiments at high density, consistent with previous results in other machines. The effect of LHCD on the current profile in EAST demonstrates that it is possible to control the plasma profile by optimizing the LHW spectrum. Repeatable H-mode plasma was obtained by LHCD and the maximum density during H-mode with the combination of 2.45 GHz and 4.6 GHz LH waves was up to 4.5 x 10(19) m(-3).

To produce in a thermonuclear fusion reactor based on the tokamak concept a sufficiently high fusion gain together stability necessary for operations represent a major challenge, which depends on the capability of driving non-inductive current in the hydrogen plasma. This request should be satisfied by radio-frequency (RF) power suitable for producing the lower hybrid current drive (LHCD) effect, recently demonstrated successfully occurring also at reactor-graded high plasma densities. An LHCD-based tool should be in principle capable of tailoring the plasma current density in the outer radial half of plasma column, where other methods are much less effective, in order to ensure operations in the presence of unpredictably changes of the plasma pressure profiles. In the presence of too high electron temperatures even at the periphery of the plasma column, as envisaged in DEMO reactor, the penetration of the coupled RF power into the plasma core was believed for long time problematic and, only recently, numerical modelling results based on standard plasma wave theory, have shown that this problem should be solved by using suitable parameter of the antenna power spectrum.We show here further information on the new understanding of the RF power deposition profile dependence on antenna parameters, which supports the conclusion that current can be actively driven over a broad layer of the outer radial half of plasma column, thus enabling current profile control necessary for the stability of a reactor.

Parametric instabilities induced at the plasma edge by lower hybrid wave power externally coupled to tokamak plasmas have, via broadening of the antenna spectrum, strong influence on the power deposition and current drive in the core. For modeling the parametric instabilities at the tokamak plasma edge in lower hybrid current drive experiments, the effect of the collisions has been neglected so far. In the present work, a specific collisional parametric dispersion relation, useful to analyze these nonlinear phenomena near the lower hybrid antenna mouth, is derived for the first time, based on a kinetic model. Numerical solutions show that in such cold plasma regions the collisions prevent the onset of the parametric instabilities. This result is important for present lower hybrid current drive experiments, as well as in fusion reactor scenarios.

Two important issues in achieving lower hybrid current drive (LHCD) high confinement plasma in EAST are to improve lower hybrid wave (LHW)-plasma coupling and to drive the plasma current at a high density. Studies in different configurations with different directions of toroidal magnetic field (Bt) show that the density near the antenna is affected by both the radial electric field induced by plasma without a LHW (Er-plasma) in the scrape off layer (SOL), and the radial electric field induced by LHW power (Er-LH) near the grill. Investigations indicate that Er× Btin the SOL leads to a different effect of configuration on the LHW-plasma coupling and Er-LH× Btaccounts for the asymmetric density behaviour in the SOL observed in the experiments, where Eris the total radial electric field in the SOL. Modelling of parametric instability (PI), collisional absorption (CA) and scattering from density fluctuations (SDF) in the edge region, performed considering the parameters of high density LHCD experiments in EAST, has shown that these mechanisms could be responsible for the low current drive (CD) efficiency at high density. Radiofrequency probe spectra, useful for documenting PI occurrence, show sidebands whose amplitude in the case of the lithiated vacuum chamber is smaller than in the case of poor lithiation, consistently with growth rates from PI modeling of the respective reference discharges. Since strong lithiation is also expected to diminish the parasitic effect on the LHCD of the remaining possible mechanisms, this appears to be a useful method for improving LHCD efficiency at a high density.

Modern research on nuclear fusion energy, based on the tokamak concept, has strong need of tools for actively driving non-inductive current especially at the periphery of plasma column, where tools available so far have poor efficiency. This is essential for solving one of the most critical problems for thermonuclear reactor, consisting in how to achieve the figure of fusion gain in the context of sufficient stability. The lower hybrid current drive (LHCD) effect has the potential capability of driving current at large radii of reactor plasma with high efficiency [1].Experiments recently carried out on EAST showed that a strong activity of LH sideband waves (from the RF probe spectra), accompanied by weak core penetration of the coupled LH power, is present when operating at relatively high plasma densities. Previous theoretical results, confirmed by experiments on FTU, showed that the LH sideband phenomenon is produced by parametric instability (PI), which are mitigated by higher plasma edge temperatures. This condition is thus useful for enabling the LH power propagation when operating with profiles having high plasma densities even at the edge.In the present work, we show new PI modeling of EAST plasmas data, obtained in condition of higher plasma edge temperature due to chamber lithisation. The obtained trend of the PI frequencies and growth rates is consistent with data of RF probe spectra, available in different regimes of lithisated and not lithisated vessel. Moreover, these spectra are interpreted as PI effect occurring at the periphery of plasma column, however in the low field side where the LH power is coupled.

The conceptual design study of a high-power high-frequency Cyclotron Auto-Resonance Maser (CARM) has been undertaken at the ENEA-Frascati research center in 2013. CARMs could be effective mm-wave sources for electron cyclotron waves and plasma diagnostics in magnetic confinement fusion reactors. The project is advancing quickly with the technical design of some major parts now completed and ready to enter the realization phase. Subsystems under conceptual or detailed design are presented together with the outlook of next steps.

High density experiments with 2.45 GHz lower hybrid current drive (LHCD) in EAST are analyzed by means of simulation and modeling, showing that parametric instabilities (PI), collisional absorption and density fluctuations in the edge region could be responsible for the low CD efficiency at high density. In addition, recent LHCD results with 4.6 GHz are presented, showing that lower hybrid wave can be coupled to plasma with low reflection coefficient, drive plasma current and modify the current profile, and heat plasma effectively. The related results between two systems (2.45 GHz and 4.6 GHz) are also compared, including CD efficiency and PI behavior.

The important goal of adding to the bootstrap a fraction of non-inductive plasma current, which would be controlled for obtaining and optimizing steady-state profiles, can be reached by using the Current Drive produced by Lower Hybrid waves (LHCD). FTU (Frascati Tokamak Upgrade) experiments demonstrated, indeed, that LHCD is effective at reactor-graded high plasma density, and the LH spectral broadening is reduced, operating with higher electron temperature in the outer region of plasma column (T-e_periphery). This method was obtained following the guidelines of theoretical predictions indicating that the broadening of launched spectrum produced by parametric instability (PI) should be reduced, and the LHCD effect at high density consequently enabled, under higher (T-e_periphery). In FTU, the temperature increase in the outer plasma region was obtained by operating with reduced particle recycling, lithized walls and deep gas fuelling by means of fast pellet. Heating plasma periphery with electron cyclotron resonant waves (ECRH) will provide a further tool for achieving steady-state operations. New FTU experimental results are presented here, demonstrating that temperature effect at the plasma periphery, affecting LH penetration, occurs in a range of plasma parameters broader than in previous work. New information is also shown on the modelling assessing frequencies and growth rates of the PI coupled modes responsible of spectral broadening. Finally, we present the design of an experiment scheduled on FTU next campaign, where ECRH power is used to slightly increase the electron temperature in the outer plasma region of a high-density discharge aiming at restoring LHCD. Consequent to model results, by operating with a toroidal magnetic field of 6.3 T, useful for locating the electron cyclotron resonant layer at the periphery of the plasma column (r/a similar to 0.8,f(0)=144 GHz), an increase of T-e in the outer plasma (from 40 eV to 80 eV at r/a similar to 0.8) is expected by the JETTO code, sufficient for recovering LHCD. An ECRH power of 0.8 MW, and the standard FTU regime at high plasma density (n(e_av)similar to 1.3x10(20) m(-3) and plasma current of 0.5 MA) have been considered. The code has been set with transport modelling to reproduce the evolution of FTU kinetic profiles.

The important goal of adding to the bootstrap current a more flexible tool, capable of producing and controlling steady-state profiles with a high fraction of non-inductive plasma current, could be reached using the lower hybrid current drive (LHCD) effect. Experiments performed on FTU (Frascati Tokamak Upgrade) demonstrated that LHCD can occur at reactor-graded high plasma density, provided that the parametric instability (PI)-produced broadening of the spectrum launched by the antenna is reduced under proper operating conditions, capable of producing relatively high temperature in the outer region of plasma column. This condition was produced by operations that reduce particle recycling from the vessel walls, and enhance the gas fuelling in the core by means of fast pellet.New results of FTU experiments are presented documenting that the useful effect of temperature at the periphery, which reduces the LH spectral broadening and enhances the LH-induced hard-x ray emission level, occurs in a broader range of plasma parameters than in previous work. Modelling results show that a further tool for helping LHCD at a high density would be provided by electron cyclotron resonant heating of plasma periphery. New information is provided on the modelling, able determining frequencies, growth rates and LH spectral broadening produced by PI, which allowed assessing the new method for enabling LHCD at high densities. Further robustness is provided to theoretical and experimental fundaments of the method for LHCD at a high density.

First pass absorption of the Lower Hybrid waves in thermonuclear devices like ITER and DEMO is modelled by coupling the ray tracing equations for the wave phase and amplitude with the quasi-linear evolution of the electron distribution function. A system of coupled ordinary differential equations for each Fourier component of the spectrum radiated by the LH antenna is derived and solved when considering both 1D/2D Fokker-Planck model for the electron distribution function. This allows to reconstruct and to evolve the quasi-linear diffusion coefficient consistently with the wave propagation, to calculate the power deposition profile and the amount of current driven by the wave. As usually assumed, the Lower Hybrid Current Drive is not effective in a plasma of a tokamak fusion reactor like ITER or DEMO, because the high electron temperature would enhance the wave absorption and then limit the RF power deposition to the very periphery of the plasma column (near the separatrix). In this work by extensively using this self-consistent modelling for the propagation and absorption of the LH wave, a parametric study on the wave spectrum (and consequently on the antenna design) as spectrum width, peak value, secondary lobes etc. has been performed very accurately. Such a careful investigation aims at controlling the power deposition layer possibly in the external half radius of the plasma, thus providing a valuable aid to the solution of how to control the plasma current profile in a toroidal magnetic configuration. This analysis is useful not only for exploring the possibility of profile control of a pulsed operation reactor, but also in order to reconsider the feasibility of steady state regime.

A Cyclotron Auto-Resonance Maser (CARM) is under study at the ENEA Research Laboratories in Frascati as a electron cyclotron heating (ECH) source in plasma magnetic confinement devices like Tokamaks. The aim of the project is the realization of a test source at 250 GHz to verify heating mechanisms in high magnetic field Tokamaks and at the second harmonics ECH frequencies for which a higher energy exchange efficiency has been predicted.