Frustraums have a higher laser-to-capsule x-ray radiation coupling efficiency and can accommodate a large capsule, thus potentially generating a higher yield with less laser energy than cylindrical Hohlraums for a given Hohlraum volume [Amendt et al., Phys. Plasmas 26, 082707 (2019]. Frustraums are expected to have less m = 4 azimuthal asymmetries arising from the intrinsic inner-laser-beam geometry on the National Ignition Facility. An experimental campaign at Lawrence Livermore National Laboratory to demonstrate the high-coupling efficiency and radiation symmetry tuning of the Frustraum has been under way since 2021. Simulations benchmarked against experimental data show that implosions using Frustraums can achieve more yield with higher ignition margins than cylindrical Hohlraums using the same laser energy. Hydrodynamic jets in capsules along the Hohlraum axis, driven by radiation-flux asymmetries in a Hohlraum with a gold liner on a depleted uranium (DU) wall, are present around stagnation, and these “polar” jets can cause severe yield degradation. The early-time Legendre mode P4<0 radiation-flux asymmetry is a leading cause of these jets, which can be reduced by using an unlined DU Hohlraum because the shape of the shell is predicted to be more prolate. Magnetization can increase the implosion robustness and reduce the required hotspot ρR for ignition; therefore, magnetizing the Frustraum can maintain the same yield while reducing the required laser energy or increase the yield using the same laser energy—all under the constraint that the ignition margin is preserved. Reducing polar jets is particularly important for magnetized implosions because of the intrinsic toroidal hotspot ion temperature topology.

Indirect Drive Inertial Confinement Fusion Experiments on the National Ignition Facility (NIF) have achieved a burning plasma state with neutron yields exceeding 170 kJ, roughly 3 times the prior record and a necessary stage for igniting plasmas. The results are achieved despite multiple sources of degradations that lead to high variability in performance. Results shown here, for the first time, include an empirical correction factor for mode-2 asymmetry in the burning plasma regime in addition to previously determined corrections for radiative mix and mode-1. Analysis shows that including these three corrections alone accounts for the measured fusion performance variability in the two highest performing experimental campaigns on the NIF to within error. Here we quantify the performance sensitivity to mode-2 symmetry in the burning plasma regime and apply the results, in the form of an empirical correction to a 1D performance model. Furthermore, we find the sensitivity to mode-2 determined through a series of integrated 2D radiation hydrodynamic simulations to be consistent with the experimentally determined sensitivity only when including alpha-heating. Recent improvements in the indirect-drive inertial confinement fusion experiments include the achievement of burning plasma state. Here the authors report the scaling of neutron yield in a burning plasma of Deuterium-Tritium fusion reaction by including the mode-2 asymmetry.

On the path towards high-gain inertial confinement fusion ignition, foams are being considered to tamp the hohlraum wall-motion, and mitigate laser backscattering from Stimulated Raman Scattering (SRS) and Stimulated Brillouin Scattering (SBS). Here we present the results from an experimental campaign on foam-filled hohlraums conducted at the OMEGA laser facility. SiO2 foam-fills, with densities as low as 1 mg/cm3, successfully reduce the gold wall expansion, with laser backscattering comparable to gas-fill.

On December 5, 2022, an indirect drive fusion implosion on the National Ignition Facility (NIF) achieved a target gain G_{target} of 1.5. This is the first laboratory demonstration of exceeding "scientific breakeven" (or G_{target}>1) where 2.05 MJ of 351 nm laser light produced 3.1 MJ of total fusion yield, a result which significantly exceeds the Lawson criterion for fusion ignition as reported in a previous NIF implosion [H. Abu-Shawareb et al. (Indirect Drive ICF Collaboration), Phys. Rev. Lett. 129, 075001 (2022)PRLTAO0031-900710.1103/PhysRevLett.129.075001]. This achievement is the culmination of more than five decades of research and gives proof that laboratory fusion, based on fundamental physics principles, is possible. This Letter reports on the target, laser, design, and experimental advancements that led to this result.

We present findings from an experimental tuning campaign aimed at igniting larger DT cryogenic layered implosions using a dual frustum shaped hohlraum, denoted "frustraum". The frustraum's distinctive shape reduces hohlraum wall losses while concurrently enhancing minimum capsule clearance with the hohlraum wall and sensitivity to pointing changes. Compared to current cylindrical hohlraum (6.4 x 11.24 mm), the frustraum has a wall area approximately 20 % smaller, resulting in a measured improvement in efficiency of around 12 %. Consequently, 12 % less laser energy is required to implode a capsule within the same acceleration timeframe. Conversely, directing the same laser energy into the frustraum yields higher ion temperatures within symmetry capsules, along with increased radiation temperatures and reduced implosion acceleration times compared to current cylindrical hohlraums.

We present quantitative motivations and assessments of various proposed and ongoing directions to further improving yields and target gain of igniting indirect-drive implosions at the National Ignition Facility (NIF). These include increasing compression and confinement time, improving hohlraum and ablator efficiency, and further increasing peak power and laser energy. 1D hydroscaled simulations, augmented by analytic 1D theory, have been used to project yield improvements for each of these implosion optimization tracks, normalized to the best current performing 4 MJ shot. At current NIF capabilities of 2.2 MJ, 450 TW, we project several paths could reach 15 MJ yield levels. We also expect several key implosion physics questions will be addressed in attempting to reach this yield level. These include demonstrating to what extent lower adiabat designs leading to higher compression will increase gain and efficiency, and whether we can reduce residual kinetic energy and ablator-fuel mix that is probably limiting the current burn-up fraction. For an envisaged NIF upgrade to EL = 3 MJ at fixed 450 TW peak power, scaling capsule size and fuel thicknesses faster than pure hydroscaling should allow for yields that could reach up to 60–80 MJ, depending on the efficiency gains realized in increasing deuterium-tritium fuel thickness, reducing hohlraum losses, and switching to lower Z ablators. The laser-plasma instability and beam transmission scaling in these larger hohlraums is shown to be favorable if the spot size is increased with hohlraum scale.

At the National Ignition Facility, inertial confinement fusion experiments aim to burn and ignite a hydrogen plasma to generate a net source of energy through the fusion of deuterium and tritium ions. The energy deposited by α-particles released from the deuterium–tritium fusion reaction plays the central role in heating the fuel to achieve a sustained thermonuclear burn. In the hydrodynamic picture, α-heating increases the temperature of the plasma, leading to increased reactivity because the mean ion kinetic energy increases. Therefore, the ion temperature is related to the mean ion kinetic energy. Here we use the moments of the neutron spectrum to study the relationship between the ion temperature (measured by the variance in the neutron kinetic energy spectrum) and the ion mean kinetic energy (measured by the shift in the mean neutron energy). We observe a departure from the relationship expected for plasmas where the ion relative kinetic energy distribution is Maxwell–Boltzmann, when the plasma begins to burn. Understanding the cause of this departure from hydrodynamic behaviour could be important for achieving robust and reproducible ignition. Inertial confinement fusion experiments reveal a departure from the expected hydrodynamic behaviour of a plasma when the fusion reactions become the primary source of plasma heating.

In indirect-drive implosions, the final core hot spot energy and pressure and, hence, neutron yield attainable in 1D increase with increasing laser peak power and, hence, radiation drive temperature at the fixed capsule and Hohlraum size. We present simple analytic scalings validated by 1D simulations that quantify the improvement in performance and use this to explain existing data and simulation trends. Extrapolating to the 500 TW National Ignition Facility peak power limit in a low gas-fill 5.4 mm diameter Hohlraum based on existing high adiabat implosion data at 400 TW, 1.3 MJ and 1 × 1016 yield, we find that a 2–3 × 1017 yield (0.5–0.7 MJ) is plausible using only 1.8 MJ of laser energy. Based on existing data varying deuterium–tritium (DT) fuel thickness and dopant areal density, further improvements should be possible by increasing DT fuel areal density, and hence confinement time and yield amplification.

We report on the first indirect-drive implosions driven by a dual conical frustum-shaped hohlraum denoted “frustraum” and the experimental tuning campaigns leading up to two layered implosions. The campaign used 1.2 and 1.4 mm inner radius high density carbon (HDC) capsules and represented the largest HDC capsules to be imploded on the National Ignition Facility via indirect drive. Several techniques were successfully implemented to control the Legendre mode 2 capsule symmetry of the implosions, including changing the wall angle of the frustraum, which is not possible with cylindrical hohlraums. A mode 4 feature was observed and its implications for hotspot mix discussed. Two layered implosions were conducted with 1.2 mm inner radius capsules, the latter of which achieved the highest layered capsule absorbed energy on the National Ignition Facility using only 1.74 MJ of laser energy. The layered implosion results, along with generalized Lawson parameters, suggest that increasing the energy absorbed by the capsule at the expense of long coast times makes it more challenging to achieve ignition and that further reducing coast time (time between end of laser pulse and bang time) closer to the 1 ns level is warranted to improve the areal density and make it easier to achieve the hotspot temperature, alpha heating, and yield amplification required for ignition.

Implosions of Hohlraum-driven double shell targets as an alternative inertial confinement fusion concept are underway at the National Ignition Facility. The double shell system relies on a series of energy transfer processes starting from thermal x-ray absorption by the outer shell, followed by collisional transfer of kinetic energy to a heavy metal inner shell, and finally, conversion to the internal energy of the deuterium-tritium fuel. During each of these energy transfer stages, low-mode asymmetries can act to reduce the ideal transfer efficiency degrading double shell performance. Mechanisms, such as hard x-ray preheat from the Hohlraum, not only decrease the efficiency of kinetic energy transfer but may also be a source of low-mode asymmetry. In this article, we evaluate the shape transfer processes through the time of shell collision using two-dimensional integrated Hohlraum and capsule computations. We find that the dominant mode of the shape transfer is well described using a “radial impulse” model from the shape of the foam pressure reservoir. To evaluate the importance of preheat on inner shell shape, we also report on first measurements of Au L-shell preheat asymmetry in a double shell with a tungsten pusher. These measurements showed a 65% higher preheat velocity at the pole of the capsule relative to the equator. We also found that the experiments provided rigorous constraints by which to test the Hohlraum model settings that impact the amount and symmetry of Au L-shell preheat via the plasma conditions inside the outer cone Au bubble.

For more than half a century, researchers around the world have been engaged in attempts to achieve fusion ignition as a proof of principle of various fusion concepts. As recently reported, a burning plasma state, where the alpha-heating in the plasma is the primary source of heating, was achieved in laboratory experiments. Following the Lawson criterion, an ignited plasma is one where the fusion heating power is high enough to overcome all the physical processes that cool the fusion plasma, creating a positive thermodynamic feedback loop with rapidly increasing temperature. In inertially confined fusion, ignition is a state where the fusion plasma can begin ``burn propagation'' into surrounding cold fuel, enabling the possibility of high energy gain. While ``scientific breakeven'' (i.e. unity target gain) has not yet been achieved, this talk reports the first controlled fusion experiment on the National Ignition Facility to produce capsule gain greater than unity (here 5.8) and reach ignition by many different formulations of the Lawson criterion. In the talk, we will discuss some key basic physics inertial confinement fusion (ICF) principles behind the burning plasma and ignition results as well as discuss future challenges.

Obtaining a burning plasma is a critical step towards self-sustaining fusion energy 1 . A burning plasma is one in which the fusion reactions themselves are the primary source of heating in the plasma, which is necessary to sustain and propagate the burn, enabling high energy gain. After decades of fusion research, here we achieve a burning-plasma state in the laboratory. These experiments were conducted at the US National Ignition Facility, a laser facility delivering up to 1.9 megajoules of energy in pulses with peak powers up to 500 terawatts. We use the lasers to generate X-rays in a radiation cavity to indirectly drive a fuel-containing capsule via the X-ray ablation pressure, which results in the implosion process compressing and heating the fuel via mechanical work. The burning-plasma state was created using a strategy to increase the spatial scale of the capsule 2 , 3 through two different implosion concepts 4 – 7 . These experiments show fusion self-heating in excess of the mechanical work injected into the implosions, satisfying several burning-plasma metrics 3 , 8 . Additionally, we describe a subset of experiments that appear to have crossed the static self-heating boundary, where fusion heating surpasses the energy losses from radiation and conduction. These results provide an opportunity to study α-particle-dominated plasmas and burning-plasma physics in the laboratory.

A goal of the laser-based National Ignition Facility (NIF) is to increase the liberated fusion energy “yield” in inertial confinement fusion experiments well past the ignition threshold and the input laser energy. One method of increasing the yield, hydrodynamic scaling of current experiments, does not rely on improving compression or implosion velocity, but rather increases the scale of the implosion to increase hotspot areal density and confinement time. Indirect-drive (Hohlraum driven) implosions carried out at two target sizes, 12.5% apart, have validated hydroscaling expectations. Moreover, extending comparisons to the best-performing implosions at five different capsule sizes shows that their performance also agrees well with hydroscaling expectations even though not direct hydroscales of one another. In the future, by switching to a reduced loss Hohlraum geometry, simulations indicate that we can drive 20% larger-scale implosions within the current power and energy limitations on the NIF. At the demonstrated compression and velocity of these smaller-scale implosions, these 1.2× hydroscaled implosions should put us well past the ignition threshold.

In the published paper titled 'Reaching 30% energy coupling efficiency for a high-density-carbon capsule in a gold rugby hohlraum on NIF' (2021 Nucl. Fusion 61 086028), the red shaded areas representing experimental uncertainties did not show up in figures 2 and 3. This corrigendum provides the correct figures 2 and 3.

An experimental program is currently underway at the National Ignition Facility (NIF) to compress deuterium and tritium (DT) fuel to densities and temperatures sufficient to achieve fusion and energy gain. The primary approach being investigated is indirect drive inertial confinement fusion (ICF), where a high-Z radiation cavity (a hohlraum) is heated by lasers, converting the incident energy into x-ray radiation which in turn drives the DT fuel filled capsule causing it to implode. Previous experiments reported DT fuel gain exceeding unity [O.A. Hurricane et al., Nature 506, 343 (2014)] and then exceeding the kinetic energy of the imploding fuel [S. Le Pape et al., Phys. Rev. Lett. 120, 245003 (2018)]. We report on recent experiments that have achieved record fusion neutron yields on NIF, greater than 100 kJ with momentary fusion powers exceeding 1PW, and have for the first time entered the burning plasma regime where fusion alpha-heating of the fuel exceeds the energy delivered to the fuel via compression. This was accomplished by increasing the size of the high-density carbon (HDC) capsule, increasing energy coupling, while controlling symmetry and implosion design parameters. Two tactics were successful in controlling the radiation flux symmetry and therefore the implosion symmetry: transferring energy between laser cones via plasma waves, and changing the shape of the hohlraum. In conducting these experiments, we controlled for known sources of degradation. Herein we show how these experiments were performed to produce record performance, and demonstrate the data fidelity leading us to conclude that these shots have entered the burning plasma regime.