Lattice structures can add value to high-performance components manufactured by laser powder bed fusion due to their high specific strength and stiffness. A further use of lattice structures is in thermo-mechanical applications, where the high surface area of the lattice may aid heat transfer. However, little characterisation of lattices under thermal loading is currently available in the literature. In this study, a custom-built test rig was used to characterise the thermal conduction for three triply periodic minimal surface lattice types, namely: gyroid, diamond and Schwarz primitives, with unit cell size and volume fraction being varied.Results show that thermal conductivity is primarily a function of the material properties and volume fraction of the sample. However, some effects of the geometry, such as surface area to volume ratio, can be used to explain slight differences in the measured conductivity. The Schwarz primitive unit cell consistently gave the highest conductivity, with diamond and gyroid unit cells being marginally lower. Larger cell sizes typically gave higher conductivity than smaller cells, which can be attributed to greater intra-cell convective heat transfer and better interface coupling with the testing apparatus.The experimental results are used to derive equations that allow samples with a specified thermal conductivity to be designed, thus demonstrating how a component may be manufactured with a custom thermal profile by varying the volume fraction of the lattice.

Developments in additive manufacturing technology are serving to expand the potential applications. Critical developments are required in the supporting areas of measurement and in process inspection to achieve this. CM247LC is a nickel superalloy that is of interest for use in aerospace and civil power plants. However, it is difficult to process via selective laser melting (SLM) as it suffers from cracking during rapid cooling and solidification. This limits the viability of CM247LC parts created using SLM. To quantify part integrity, spatially resolved acoustic spectroscopy (SRAS) has been identified as a viable non-destructive evaluation technique. In this study, a combination of optical microscopy and SRAS was used to identify and classify the surface defects present in SLM-produced parts. By analysing the datasets and scan trajectories, it is possible to correlate morphological information with process parameters. Image processing was used to quantify porosity and cracking for bulk density measurement. Analysis of surface acoustic wave data showed that an error in manufacture in the form of an overscan occurred. Comparing areas affected by overscan with a bulk material, a change in defect density from 1.17% in the bulk material to 5.32% in the overscan regions was observed, highlighting the need to reduce overscan areas in manufacture.

A major factor limiting the adoption of powder-bed-fusion additive manufacturing for production of parts is the control of build process defects and the effect these have upon the certification of parts for structural applications. In response to this, new methods for detecting defects and to monitor process performance are being developed. However, effective utilisation of such methods to rework parts in process has yet to be demonstrated. This study investigates the use of spatially resolved acoustic spectroscopy (SRAS) scan data to inform repair strategies within a commercial selective laser melting machine. New methodologies which allow for rework of the most common defects observed in selective laser melting (SLM) manufacturing are proposed and demonstrated. Three rework methodologies are applied to targeted surface breaking pores: a hatch pattern, a spiral pattern and a single shot exposure. The work presented shows that it is possible to correct surface breaking pores using targeted re-melting, reducing the depth of defects whilst minimising changes in local texture. For the hatch rework and spiral rework, a reduction in defect depth of 50 % and 31 % were observed, respectively, however, no improvement was seen after the single shot exposures. This work is part of a programme to develop a method by which defects can be detected and the part reworked in-process during SLM to enable defect specification targets to be met. Although further work in developing build-characterise-rework strategies for integrated and targeted defect correction is needed, the feasibility of the underlying method of identifying and selectively reworking to reduce a defect has now been demonstrated for the first time.

The high thermal gradients experienced during manufacture via selective laser melting commonly result in cracking of high γ/γ′ Nickel based superalloys. Such defects cannot be tolerated in applications where component integrity is of paramount importance. To overcome this, many industrial practitioners make use of hot isostatic pressing to ‘heal’ these defects. The possibility of such defects re-opening during the component life necessitates optimisation of SLM processing parameters in order to produce the highest bulk density and integrity in the as-built state. In this paper, novel fractal scanning strategies based upon mathematical fill curves, namely the Hilbert and Peano-Gosper curve, are explored in which the use of short vector length scans, in the order of 100 μm, is used as a method of reducing residual stresses. The effect on cracking observed in CM247LC superalloy samples was analysed using image processing, comparing the novel fractal scan strategies to more conventional ‘island’ scans. Scanning electron microscopy and energy dispersive X-ray spectroscopy was utilised to determine the cracking mechanisms. Results show that cracking occurs via two mechanisms, solidification and liquation, with a strong dependence on the laser scan vectors. Through the use of fractal scan strategies, bulk density can be increased by 2 ± 0.7% when compared to the ‘island’ scanning, demonstrating the potential of fractal scan strategies in the manufacture of typically ‘unweldable’ nickel superalloys.

This study explores the capabilities of methods for in-situ synthesis of titanium aluminides using the Direct Metal Deposition process. This allows for the functional grading of components which will be required for next generation aerospace components. The feasibility of three techniques are explored here; firstly, a new process of powder preparation for Additive Manufacturing, satelliting, in which a larger parent powder is coated with a smaller powder fraction. Here, Al parent particles are satellited with fine TiO2 to produce an intermetallic matrix composite with Al2O3 particulates. The satelliting procedure is shown to increase capability and mixing of in situ synthesis. Secondly, combined wire and single powder feeding is explored through the use of Ti wire and Al powder to create Ti-50Al (at%). Finally, a combination of wire and loose mixed powders is explored to produce the commercially deployed Ti-48Al-2Cr-2Nb (at%) alloy. The simultaneous wire and powder delivery is designed to overcome issues encountered when processing with single powder or wire feedstocks, whilst allowing for on-the-fly changes in elemental composition required for functional grading. Characterisation of the deposits produced, through OM, SEM, and EDX, reveal the influence of key processing parameters and provides a meaningful basis for comparison between the techniques. Results show that it is possible to produce 2 + two-phase microstructures consistent with previous studies which have relied upon more expensive and harder to obtain pre-alloyed feedstocks. This represents a move forward in manufacturability for an emergent

This study explores the capabilities of methods for in-situ synthesis of titanium aluminides using the Direct Metal Deposition process. This allows for the functional grading of components which will be required for next generation aerospace components. The feasibility of three techniques are explored here; firstly, a new process of powder preparation for Additive Manufacturing, satelliting, in which a larger parent powder is coated with a smaller powder fraction. Here, Al parent particles are satellited with fine TiO2 to produce an intermetallic matrix composite with Al2O3 particulates. The satelliting procedure is shown to increase capability and mixing of in situ synthesis. Secondly, combined wire and single powder feeding is explored through the use of Ti wire and Al powder to create Ti-50Al (at%). Finally, a combination of wire and loose mixed powders is explored to produce the commercially deployed Ti-48Al-2Cr-2Nb (at%) alloy. The simultaneous wire and powder delivery is designed to overcome issues encountered when processing with single powder or wire feedstocks, whilst allowing for on-the-fly changes in elemental composition required for functional grading. Characterisation of the deposits produced, through OM, SEM, and EDX, reveal the influence of key processing parameters and provides a meaningful basis for comparison between the techniques. Results show that it is possible to produce α2+γ two-phase microstructures consistent with previous studies which have relied upon more expensive and harder to obtain pre-alloyed feedstocks. This represents a move forward in manufacturability for an emergent process type.