High Mn austenitic steels are considered an economical alloy system for hydrogen storage and transport applications. This study used stacking fault energy (SFE) as a design parameter to achieve hydrogen embrittlement (HE)-resistant high Mn austenitic alloys. The role of hydrogen on the deformation mechanisms of low (29 mJ/ m2) and high SFE (49 mJ/m2) alloys was evaluated through in-situ neutron diffraction during tensile loading. Hydrogen-precharging increased yield strength, partly due to hydrogen-induced lattice distortion (i.e., solute strengthening). Hydrogen accelerated the increase in defect density, including dislocations and stacking faults. The formation of planar deformation structures (twins and stacking faults), relative to dislocations, plays a critical role in promoting hydrogen-assisted fracture. The stacking fault frequency parameter obtained from neutron diffraction quantifies planar deformation tendencies, correlated with HE sensitivity. The higher SFE alloy exhibited greater resistance to HE, associated with the reduced propensity to form stacking faults and twins upon deformation in the hydrogen-precharged condition.

Reliable radiographic methods for characterizing nuclear waste packages non-destructively (without the need to open containers) have the potential to significantly contribute to safe handling and future disposal options, particularly for legacy waste of unknown content. Due to required shielding of waste containers and the need to characterize materials consisting of light elements, X-ray methods are not suitable. Here, energy-resolved MeV neutron radiography is demonstrated as a first-of-its-kind application for non-destructive and remote examination of mock up nuclear waste packages from a safe position using time-of-flight techniques enabled by a novel event-mode imaging detector system. Energy-resolved neutron transmission spectra were measured spatially, permitting the detection of analogue materials to actual nuclear waste such as water, melamine, and ion exchange resin within a 2.54 cm wall thickness steel pipe. The results demonstrate the capability to locate the materials through this wall thickness by radiography and tomographic reconstruction, revealing detailed 3D distributions and structural anomalies. The method effectively detects residual water in ion exchange resin, highlighting its sensitivity to moisture content, a crucial parameter for nuclear waste characterization. Monte Carlo simulations are in agreement with the experimental findings, providing a pathway to simulate waste forms more difficult to tackle experimentally. This work paves the way to apply sub-nanosecond intense MeV neutron sources, such as laser-driven neutron sources under development, to nuclear waste characterization.

Molten fluoride salts such as Li 2 BeF 4 (FLiBe) are used in molten salt reactors, fluoride-salt-cooled high-temperature reactors and fusion reactors as a fuel solvent, coolant and/or tritium breeding medium. In engineered systems that use molten salt, solid-state material will be present during melting and freezing scenarios, and therefore the temperature-dependent properties of the solid and solid/liquid phase transition merit investigation. To observe the behavior of the solid state of Li 2 BeF 4 from room temperature to melting, this work used neutron and X-ray diffraction to measure the changes in the lattice parameters and volume of the crystalline unit cell and compared the results with prior low-temperature data for solid Li 2 BeF 4 . From neutron diffraction data it is also possible to identify anisotropy: centimetre-scaled crystals align preferentially with the a axes parallel to the direction of freezing front propagation, and the c axes expand 54% more than the a axes. This work provides the lattice constants as a function of temperature, quantifies the thermal expansion, and determines the equation describing the change in density for solid Li 2 BeF 4 from room temperature to 459°C to be ρ solid (kg m −3 ) = 2182 (3) − 0.115 (2) T (°C) and the volume expansion upon melting to be less than 5%. This density changes depending on molecular weight and enrichment.

Time-of-flight neutron diffraction and energy-resolved imaging each provide unique perspectives into material properties. Neutron diffraction is useful for assessing microstructural parameters such as phase composition, texture, and dislocation densities, though it typically provides averaged data over the sampled volume. Energy-resolved imaging, on the other hand, offers both spatial and spectral information by detecting Bragg edges and neutron absorption resonances, which enables detailed mapping of microstructure and isotopic composition. When combined, these techniques have the potential to enrich our understanding of material behavior across different scales, enhancing our understanding of complex materials. Traditionally, these modalities are conducted on separate instruments, which is time-consuming and poses challenges for data integration. Here, we report the integration of the LumaCam, an event-mode energy-resolved neutron imaging camera with the HIPPO time-of-flight diffractometer at LANSCE. This integration enables simultaneous diffraction and imaging across the full spectrum, with analysis optimized for diffraction and Bragg-edge imaging in the thermal range (0.45–10 Å) and resonance imaging in the epithermal range (0.5–3000 eV), facilitating comprehensive multi-modal analysis. We demonstrate its capabilities through case studies, including spatial mapping of grain orientations in a steel sample and accurate thickness estimations for irregular samples including a depleted uranium cylinder and a natural silver-containing mineral specimen. The combined setup enhances real-time sample alignment and provides comprehensive data for crystal structure, texture, and isotopic composition analysis. This approach opens new possibilities for advanced applications in nuclear engineering, archaeology, and materials science.

A large-area event-mode camera system coupled with a $$^{6}$$ LiF-ZnS:Ag scintillator is applied for neutron resonance imaging (NRI) on the energy-resolved neutron imaging (ERNI) flight path, also known as Flight Path 5 (FP5), at the Los Alamos Neutron Science Center (LANSCE). This novel neutron imaging system, featuring a 120 $$\times$$ 120 mm $$^2$$ field of view, efficiently captures resonance information across the entire image in a single acquisition, significantly reducing beam time requirements compared to conventional energy-resolved neutron imaging systems. High-quality neutron radiographs with enhanced spatial resolution are achieved through the reconstruction of neutron events based on observations of individual photons emitted from the scintillator. The system demonstrates reduced background through neutron/gamma discrimination capabilities while maintaining sharpness across a large fields of view. In the measurements presented here, a spatial resolution of approximately 340 $$\mu$$ m was achieved using center-of-gravity photon cluster centroiding. We demonstrate the system’s capability for quantitatively determining isotopic distributions in various thin samples, as well as automatically reconstructing complex scenes with overlapping resonances from diverse samples. These results are obtained using standard data analysis tools, despite the relatively slow $$^{6}$$ LiF-ZnS:Ag scintillator, which may not be optimal for absorption resonance detection. The capabilities demonstrated here offer a valuable, versatile, and cost-effective solution for high spatial and temporal resolution, large field-of-view energy-resolved neutron imaging, with potential applications across various scientific and industrial domains.

Tantalum pentoxide (Ta2O5) is a component of technologies ranging from photographic lenses to medical implants. Despite more than six decades of interest, however, there is no consensus on the crystal structure of Ta2O5. Here, we report the results of neutron diffraction experiments on Ta2O5 powders at temperatures up to 1000 degrees C. Because neutron diffraction is sensitive to the positions of O atoms in the presence of heavy elements, our results provide strong evidence that the orthorhombic LSR structure can account for experimental observations better than any other proposal in the literature. We also determine the anisotropic crystallographic thermal expansion parameters of Ta2O5, which are important for modeling the performance of Ta2O5-bearing technologies.

Thermal neutron detection in neutron scattering science is a challenging endeavour due to a limited number of technologies which are sensitive to these weakly interacting particles. While many improvements to conventional detectors are underway at various facilities, there is a great opportunity to make a leap in performance by combining the spatial resolution benefits of imaging and the temporal resolution and background discrimination of event-driven radiation detectors. This idea has been realized by using a neutron sensitive scintillator read out by a single-photon sensitive camera based on a Timepix3 ASIC. We demonstrate how such data-driven imaging sensors can enable unprecedented performance in neutron reflectometry using the ASTERIX instrument at the Los Alamos Neutron Scattering Center. Several samples were measured with both the new and a conventional [Formula: see text]He detector systems. The results from this work demonstrate that these imaging based systems can satisfy performance parameters for the future QIKR reflectometer to be built at the Second Target Station at Oak Ridge National Laboratory. Further improvements to the detector are already underway which will allow streamlined and expedited experiments. We demonstrate at least a two order of magnitude increase in detection rate at an acceptable dead time and introduce a new way of tuning the detector efficiency using light collecting optics to accommodate highly intense direct beams which cannot be measured with any current detectors without severe attenuation. This will allow measurements of complete reflectometry profiles and using a single sample measurement combined with fewer direct beam calibration measurements on QIKR and potentially other reflectometers.

Zirconium hydride is a promising candidate material for nuclear microreactor applications as a solid-state moderator component, owing to its favorable neutronics properties and good thermal stability over other metal hydrides. In the present work, the crystal structure, thermal expansion, and elastic properties of the hydrogen-rich epsilon phase hydride were measured at elevated temperatures in the range 300-900 K. Samples were prepared by direct hydriding Zircaloy-4 metal - a nuclear-grade zirconium alloy. Room-temperature lattice parameters agree well with those reported from literature for unalloyed zirconium hydride and fall within an observed quadratic H-content dependence. The coefficients of thermal expansion, determined from lattice expansion and dilatometry, agree well within our work but were about 30 % lower than those reported by others for unalloyed hydrides. Density functional theory-based molecular dynamics simulations were used to compare with thermal expansion and elasticity measurements. Results showed lattice parameter temperature dependence and slope of thermal expansion align with those from measurements. Based on diffraction scans at select temperatures, epsilon phase remained stable in air up to at least 770 K. Likewise, dilatometry showed smooth thermal expansion up to the thermal decomposition temperature around 950 K. The precise decomposition temperature was not determined via diffraction due to sparse scanning. The complete elastic property measurements were gathered for epsilon-phase Ziracloy-4 hydride for the first time. Young's modulus was lower compared to the metal and delta hydride phases. High-temperature elasticity measurements were limited to <350 K due to acoustic dissipation effects.

Nuclear fuels able to withstand hydrogen exposure >2227 degrees C with minimal chemical and mechanical changes are required to enable nuclear thermal propulsion reactors for deep space exploration. Previously (U0.2Zr0.8)C was demonstrated to exhibit minimal mass loss, while maintaining structural integrity, when exposed to hydrogen at 2327 degrees C for 3 h. Here, various techniques were implemented for an in-depth characterization of that same sample. X-ray and neutron diffraction were used to assess for formation of secondary phases and to examine lattice parameter changes on the surface and the bulk of the material by probing the full volume of the 8 x 8 x 12 mm sample. In addition, nano-indentation and microstructural characterization were conducted to understand the impact of hydrogen exposure to the mechanical properties and internal microstructure of the material. The results indicate that: 1) no new phases were observed throughout the volume of the hydrogen-exposed sample, nor any lattice parameter evolution was reported suggesting the composition of the sample following hydrogen exposure remained unchanged; 2) the microstructure was not significantly altered, although a small reduction in the grain size (as-fabricated: 12.9 +/- 2.98 mu m, hydrogen exposed: 8.6 +/- 2.71 mu m) and an increase in porosity (as-fabricated: 97.82 % theoretical density (TD), hydrogen exposed: 89.31 % TD) were observed; 3) the hardness of the hydrogen-exposed material did increase by similar to 8.5 % when compared to the as-fabricated material and the hardness of the hydrogen exposed sample was shown to decrease with increasing temperature, as expected based on experience with ZrC. This detailed post-characterization examination, which is the first of its kind for fuels exposed to pure hydrogen at 2327 degrees C, suggests (U0.2Zr0.8)C would be incredibly resistant against chemical, dimensional, and mechanical changes when exposed to high temperature hydrogen during operation of a nuclear thermal propulsion reactor, making it an attractive fuel choice.

An elasto-plastic self-consistent crystal plasticity model integrating a stress state-dependent martensitic transformations model and a hardening law based on the evolution of dislocation densities was used to model and interpret the deformation behavior of 316 L stainless steel. The deformation of constituent grains in the model involved a combination of anisotropic elasticity and plasticity via crystallographic slip and phase transformations. The steel was tested in simple tension under several strain-rates and temperatures to record the data for the identification of model parameters. The calibrated and validated EPSC model was then used as a constitutive law in implicit finite elements (FE) for solving several boundary value problems including inflation/tension of microtubes and biaxial tension of sheets. These multi-level simulations enabled the verification of the FE-EPSC model to capture the strain-path sensitive deformation of the 316 L tubes and sheets. The extent of alpha(y)-martensite volume fraction and texture evolution were measured using electron-backscattered diffraction (EBSD) and neutron diffraction, while the strain fields were measured using digital image correlation (DIC) technique for the multi-level model verification. The evolution of geometry, mechanical fields, phases, and texture were predicted to agree well with the experimental measurements. The model successfully predicted more martensite formation under biaxial tension than uniaxial tension, consistent with the experimental measurements. Favorable comparisons of the predictions and experimental measurements allowed us to rationalize the origins of the martensitic transformation trends with deformation in 316 L steel. Although the uniaxial loading evolved crystallography of the structure to favor the martensitic transformation, the biaxial loading induced stress fields in the grains to cause large separations between partial dislocation giving rise to a greater extent of the martensitic transformation in biaxial than uniaxial loading.

Self-irradiation in plutonium is a continuous process that introduces radiation damage ranging from point defects to nanoscale radiation damage as well as decay daughter product impurities that require to be accommodated by the host material. These changes are affecting the structure and properties of the material by lattice swelling, mechanical strengthening, and other alterations. X-ray diffraction and dilatometry studies have shown that the room temperature self-irradiation of delta-phase Pu-Ga alloys (2 and 7 at%Ga) results in swelling of the lattice that saturates after 0.1-0.2 displacement per atom (dpa) of accumulated lattice damage. For a better understanding of these self- irradiation processes, defect accumulation and damage evolution, this time-of-flight neutron diffraction study investigates the impact of ambient self-irradiation effects on the structural evolution of delta-phase Pu-239-Ga alloys exposed to cryogenic temperatures (<120 K), associated with a varied history of storage time and thermal treatments. Two key behaviors were observed in the lattice evolution after exposure to cryogenic temperatures with respect to room-temperature accumulated self-irradiation damage. Samples with no self- irradiation damage accumulation under ambient conditions showed swelling of the lattice at the end of the measurement, while samples that accumulated significant self-irradiation damage under ambient conditions showed only a partial recovery of the lattice parameter value upon completion of the measurements (cooling followed by heating back to room temperature). Possible causes of the behavior are proposed, and their associated effects are discussed.

Neutron diffraction beamlines have traditionally relied on deploying large detector arrays of 3He tubes or neutron-sensitive scintillators coupled with photomultipliers to efficiently probe crystallographic and microstructure information of a given material. Given the large upfront cost of custom-made data acquisition systems and the recent scarcity of 3He, new diffraction beamlines or upgrades to existing ones demand innovative approaches. This paper introduces a novel Timepix3-based event-mode imaging neutron diffraction detector system as well as first results of a silicon powder diffraction measurement made at the HIPPO neutron powder diffractometer at the Los Alamos Neutron Science Center. Notably, these initial measurements were conducted simultaneously with the 3He array on HIPPO, enabling direct comparison. Data reduction for this type of data was implemented in the MAUD code, enabling Rietveld analysis. Results from the Timepix3-based setup and HIPPO were benchmarked against McStas simulations, showing good agreement for peak resolution. With further development, systems such as the one presented here may substantially reduce the cost of detector systems for new neutron instrumentation as well as for upgrades of existing beamlines.

AbstractEnergy-resolved fast-neutron radiography is a powerful non-destructive technique that can be used to remotely measure the quantity and distribution of elements and isotopes in a sample. This is done by comparing the energy-dependent neutron transmission of a sample with the known cross-sections of individual isotopes. The reconstruction of the composition is possible due to the unique features (e.g. resonances) in the cross-sections of individual isotopes. At short-pulsed ($${\lesssim }$$ 1 ns) neutron sources, such information is accessible via time-of-flight neutron imaging in principle, but requires a detector with nanosecond temporal resolution. Conventional neutron detectors can meet this requirement only by heavily compromising spatial resolution or efficiency. Here, we present a unique approach on fast neutron resonance radiography using a scintillator-based event-mode imaging detector at a short-pulsed neutron source, including first results on spatially mapped resonance profiles using MeV neutrons. The event mode approach applied in the presented detector allows recording of individual neutron interactions with nanosecond precision in time and sub-mm resolution in space. As a result, the entire available neutron energy spectrum can be measured for each pulse. At the same time, the use of a thick scintillator screen and lenses to focus the produced light results in a highly flexible field of view and a high interaction probability in the sensitive volume of the detector.

X-ray free electron laser (XFEL) sources coupled to high-power laser systems offer an avenue to study the structural dynamics of materials at extreme pressures and temperatures. The recent commissioning of the DiPOLE 100-X laser on the high energy density (HED) instrument at the European XFEL represents the state-of-the-art in combining x-ray diffraction with laser compression, allowing for compressed materials to be probed in unprecedented detail. Here, we report quantitative structural measurements of molten Sn compressed to 85(5) GPa and ∼3500 K. The capabilities of the HED instrument enable liquid density measurements with an uncertainty of ∼1% at conditions which are extremely challenging to reach via static compression methods. We discuss best practices for conducting liquid diffraction dynamic compression experiments and the necessary intensity corrections which allow for accurate quantitative analysis. We also provide a polyimide ablation pressure vs input laser energy for the DiPOLE 100-X drive laser which will serve future users of the HED instrument.

Microstructure-aware models are necessary to predict the behavior of material based on process knowledge or to extrapolate mechanical properties of materials to environmental conditions which are not easily reproduced in the laboratory, e.g., nuclear reactor environments. Elemental Ta provides a relatively simple BCC system in which to develop a microstructural understanding of deformation processes which can then be applied to more complicated BCC alloys. In situ neutron diffraction during compressive deformation and subsequent heat treatment have been used to monitor the evolution of microstructural features in Ta throughout simulated processing steps. Crystallographic texture and dislocation density are determined as a function of first plastic strain, then temperature. Lattice strains are determined and attributed to stresses at macroscopic, grain and dislocation length scales. The increase of the dislocation density through deformation and subsequent recovery during heat treatment is monitored through the changing diffraction line profile. Also, randomization of the texture is used as a signature of recrystallization. The recovery of dislocations through annihilation is not observed to depend on the initial dislocation density in the range studied here. In contrast, recrystallization is observed to depend strongly on the initially dislocation density.

Austenitic steels have relatively high resistance to hydrogen embrittlement and play a critical role in hydrogen service applications. In particular, high Mn austenitic steels are considered economically viable alloy alternatives for these applications. The current study employed in-situ and ex-situ neutron diffraction techniques combined with diffraction line profile analysis (DLPA) to investigate the influence of hydrogen on deformation and embrittlement mechanisms in a high Mn (approximately 30 wt pct) austenitic steel. Investigation using both neutron diffraction and electron backscatter diffraction revealed the presence of extensive deformation twins and stacking faults within the steel microstructure after tensile deformation in the non-charged condition. These microstructural features suggest planar deformation behavior, which is expected from the relatively low stacking fault energy (SFE) of the alloy (approximately 29 mJ/m2). Hydrogen pre-charging resulted in apparent increases in both dislocations and stacking faults, contributing to macroscopic hardening and embrittlement mechanisms. Overall, numerical parameters obtained through neutron DLPA were used to elucidate the underlying mechanisms associated with hydrogen effects on the mechanical behavior, i.e. macroscopic strengthening, strain hardening rate, and embrittlement.

Comprehensive information on in situ microstructural and crystallographic changes during the preparation/manufacturing processes of various materials is highly necessary to precisely control the microstructural morphology and the preferred orientation (or texture) characteristics for achieving an excellent strength–ductility–toughness balance in advanced engineering materials. In this study, in situ isothermal annealing experiments with cold-rolled 17Ni-0.2C (mass%) martensitic steel sheets were carried out by using the TAKUMI and ENGIN-X time-of-flight neutron diffractometers. The inverse pole figures based on full-profile refinement were extracted to roughly evaluate the preferred orientation features along three principal sample directions of the investigated steel sheets, using the General Structure Analysis System (GSAS) software with built-in generalized spherical harmonic functions. The consistent rolling direction (RD) inverse pole figures from TAKUMI and ENGIN-X confirmed that the time-of-flight neutron diffraction has high repeatability and statistical reliability, revealing that the principal preferred orientation evaluation of steel materials can be realized through 90° TD ➜ ND (transverse direction ➜ normal direction) rotation of the investigated specimen on the sample stage during two neutron diffraction experiments. Moreover, these RD, TD, and ND inverse pole figures before and after the in situ experiments were compared with the corresponding inverse pole figures recalculated from the MUSASI-L complete pole figure measurement and the HIPPO in situ microstructure evaluation, respectively. The similar orientation distribution characteristics suggested that the principal preferred orientation evaluation method can be applied to the in situ microstructural evolution of bulk orthorhombic materials and spatially resolved principal preferred orientation mappings of large engineering structure parts.

Controlling microstructural evolution in metallic additive manufacturing (AM) is difficult, especially in producing refined as-built grains instead of coarse, directional grains. Traditional solutions involve adding inoculants to AM feedstocks, but titanium (Ti) alloys cannot employ this approach without producing detrimental secondary phases. Ti-Cu (Ti-copper) alloys offer a solution through constitutional supercooling and/or solid state thermal cycling under AM conditions. This work analyzes a compositionally graded directed energy deposition (DED) Ti-Cu build, single-melt laser tracks, and dilatometric heat treatments to evaluate if, when, and by what mechanism(s) microstructural refinement occurs. Refinement by inoculation of unmelted powder particles was also considered. Constitutional supercooling produced no net microstructural refinement as any equiaxed dendrites which form are remelted with new deposition. This finding agreed with solidification modeling of powder bed fusion-laser beam (PBF-LB) and DED builds. Solid state thermal cycling refined microstructures only during ex-situ dilatometric heat treatments, suggesting build parameter optimization is needed to achieve refinement in-situ. Accidental heterogeneous nucleation on unmelted Ti powder, originating from the different thermophysical properties of Ti and Cu, provided the most significant microstructural refinement. This work systematically assesses the microstructural refinement mechanisms of Ti-Cu in AM builds and offers insights into microstructural control in eutectoid alloys.

Heusler compounds are intermetallic alloys that are capable of a wide range of unique properties such as magnetocaloric, thermoelectric, and magnetic-shape-memory effects, antiferromagnetism, superconductivity, and they can even act as topological insulators. These multifunctional behaviors make Heusler alloys prime candidates for numerous smart device applications. However, their specific properties critically depend on their crystalline structures, chemical order, structural phase transformations, and crystallographic texture. Thus, as compositions and processing parameters are varied it becomes essential to be able to accurately characterize the structure of these materials at various scales. This paper provides a brief review of diffraction-based characterization techniques ideally suited for the characterization of Heusler alloys with examples from our previous works including use of synchrotron, neutron, and electron diffraction, especially as a function of temperature and/or magnetic field to explain important phenomena demonstrated by Heusler alloys.