Today, environmental issues became a matter of worldwide concern. In particular, the major cause of greenhouse gas and environmental pollution is the automobile industry. Research is taking place to on materials to reduce a vehicles weight. In this paper, the Out-of-plane ESPI method was used to measure the internal defect of low weight and high pressure vessels. ESPI measurement method has many advantages. One advantage is that it is not only non-destructive and a non-contacting form of measurement, but it also does real time and precise measurements. The Out-of-plane ESPI system is a measurement of the deformation of an object. Therefore, it is very difficult to measure internal defect length by the Out-of-plane ESPI system. In the case of when deformation is converted into strain it is possible to measure internal defect length, because strain indicates a stress concentration. Interpreted results of the FEM method and the results of the Out-of-plane ESPI were compared for quantitative values of internal defect in the pressure vessel.

Moiré topography method is a well-known non-contacting 3-D measurement method. Recently, the automatic 3-D measurement technique by moiré topography has been developed in order to apply to the engineering and medical fields. The projection moiré topography is very attractive because of its high measuring speed and high sensitivity. In this paper, using the two-wavelength methods of projection moiré topography was investigated to measure the 3-D shape of an object with 2π-ambiguity problems. Rapid measurement can be accomplished by the synchronization between CCD camera and projector. The experimental results prove that the proposed scheme is capable of finding absolute fringe orders, so that the 2π-ambiguity problems can be effectively overcome so as to treat large step discontinuities in measured objects.

topography method is a well-known non-contacting 3-D measurement method. Recently, the automatic 3-D measurement by topography has been required, since the method was frequently applied to the engineering and medical fields. The 3-D measurement using projection topography is very attractive because of its high measuring speed and high sensitivity. In this paper, using two-wavelength method of projection topography was tested to measuring object with problems. The experimental results prove that the proposed scheme is capable of finding absolute fringe orders, so that the problems can be effectively overcome so as to treat large step discontinuities in measured objects.

Laser interferometry is widely used as a measuring system in many fields because of its high resolution and ability to measure a broad area in real-time all at once. In conventional LASER interferometry, for example Out-of-plane ESPI(Electronic Speckle Pattern Interferometry), In plane ESPI, Shearography and Holography, it uses PZT or other components as a phase shift instrumentation to extract 3D deformation data., vibration mode and others. However, in most cases PZT has some disadvantages, which include non-linear errors and limited time of use. In the present study, a new type of LASER interferometry using a laser diode is proposed. Using LASER Diode Sinusoidal Phase Modulating (LD-SPM) interferometry, the phase modulation can directly modulated by controlling the LASER Diode injection current thereby eliminating the need for PZT and its components. This makes the interferometry more compact. This paper reports on a new approach to the LD Modulating interferometry that involves four-bucket phase shift method. This study proposes a four-bucket phase mapping algorithm, which developed to have a guaranteed application, to stabilize the system in the field and to be a user-friendly GUI. In this paper, LD modulating interferometry had shown the theory for LD wavelength modulation and sinusoidal phase modulation. Four-bucket phase mapping algorithm then introduced.

The ESPI (Electronic Speckle Pattern Interferometry) is a real-time, full-field, non-destructive optical measurement technique. In this study, ESPI was proposed for the purpose of vibration analysis for new and composite materials. Composite materials have various complicated characteristics according to the materials, orientations, stacking sequences of the ply and boundary conditions. Therefore, it was difficult to analyze composite materials. For efficient use of composite materials in engineering applications the dynamic behavior (i.e., natural frequencies and nodal patterns) should be informed. With the use of Time-Average ESPI, one could analyze vibration characteristics of composite material by real time easily. We manufactured two kinds of laminated composites (i.e., symmetry and asymmetry) which were consisted of CFRP (Carbon Fiber Reinforced Plastics) and the shape of the test piece was of rectangular form.

Recently, laser interferometry is widely used as a measuring system in many fields because of its high resolution and its ability to measure a broad area in real-time all at once. In conventional laser interferometry, for example Out-of-plane ESPI (Electronic Speckle Pattern Interferometry), In plane ESPI, Shearography and Holography, it uses PZT or other components as a phase shift instrumentation to extract 3-D deformation data, vibration mode and others. However, in most cases PZT has some disadvantages, which include nonlinear errors and limited time of use. In the present study, a new type of laser interferometry using a laser diode is proposed. Using Laser Diode Sinusoidal Phase Modulating (LD-SPM) interferometry, the phase modulation can be directly modulated by controlling the laser diode injection current thereby eliminating the need for PZT and its components. This makes the interferometry more compact.

A phase shifting pulsed holographic interferometer was applied to the experimental study of the propagation of laser-induced shock waves over metal plates. A double-pulsed ruby laser was used to generate the shock waves and to make a holographic interferogram of the wave fields. The phase shifting method with a dual-reference beam solved the sign ambiguity problem in holographic fringe patterns and allowed a quantitative evaluation of the phase of the interference patterns. The transient surface profile and propagation behavior of the shock wave over plates were investigated from the holographic fringe patterns.

Moire topography method is a well-known non-contacting 3-D measurement method. Recently, the automatic 3-D measurement by moire topography has been required since the method was frequently applied to the engineering and medical fields. The 3-D measurement using projection moire topography is very attractive because of its high measuring speed and high sensitivity. In this paper, using the two-wavelength methods of projection moire topography was tested to a measuring object with 2pi-ambiguity problems. Also, rapid measurement can be accomplished by the synchronization between CCD camera and projector. The experimental results prove that the proposed scheme is capable of finding absolute fringe orders, so that the 2pi-ambiguity problems can be effectively overcome so as to treat large step iscontinuities in measured objects.

Electronic speckle contouring(ESC) is the optical method for measuring shape by using fringe-projection techniques in electronic speckle pattern interferometry. It has the advantage of being non-contacting and can also give a field view of the surface under investigation. Fringes in ESC represent the difference in depth along the view direction between the master wavefront and the test component. The contour maps of three-dimensional diffuse objects are obtained by small shifts of optical fiber carrying the dual-object-beams and 4-frame phase shift. We proposed the contouring method by shifting the collimated illumination beams through optical fiber in order to obtain the contour fringe patterns. And also, we performed addition of incremental addition of images and experiments based on it. we obtained both quantitative increment without decorrelation effect and qualitative improvement by reducing the noise of contour fringes.

Moire topography method is a well-known non-contacting 3-D measurement method. Recently, the automatic 3-D measurement by moire topography has been required since the method was frequently applied to the engineering and medical fields. 3-D measurement using projection moire topography is very attractive because of its high measuring speed and high sensitivity. In this paper, using two-wavelength methods of projection moire topography was tested to a measuring object with 2pi -ambiguity problems. Experimental results prove that the proposed scheme is capable of finding absolute fringe orders, so that the 2pi -ambiguity problems can be effectively overcome so as to treat large step discontinuities in measured objects.

More accurate and fast inspection method for mechanical parts and structure is required to guarantee the safety. Conventional methods using compliance method, eddy current method, ultrasonic wave, acoustic emission for non-destructive testing in mechanical parts and structure have been performed as the method of contact with objects to be inspected. With this reason these methods have been taken relatively much time, money, and manpower. In this study, in order to overcome these shortcomings, we used In-plane Electronic Speckle pattern Interferometry(In-plane ESPI) that was full-field measurement and noncontact method. We detected the cracks of the specimen at a real time and measured the length of the crack by using In-place ESPI system. Finally, we compared this results with conventional microscope method.

It is very important that we understand the dynamic behaviors of the laser induced plume in welding, because the laser induced plume has considerable effects on welding efficiency and the quality of materials. Many experimental studies have been performed in order to observe the plume behaviors using a visualization method. In this paper, we describe the visualization and quantification of the laser induced plumes by pulse holographic interferometry. A pulsed Nd:YAG laser was used for the generation of laser induced plume and a Q-switched Ruby laser was employed to record the weld plume. For qualitative visualization of the laser induced plume, we used the double-exposure holographic interferometry. Then, we chose the quasi-heterodyne holographic interferometry with the dual-reference-beam and phase shifting in order to visualize the plume quantitatively. The experimental results show the visible behavior of the laser induced plume according to a change in the output power of the pulsed Nd:YAG laser and the time delay of Q-switched Ruby laser. Finally, we obtained the quantitative results by using the dual-reference-beam.

Residual stress is one of the causes which makes defects in engineering components and materials. These residual stresses can occur in many engineering structures and can sometimes lead to premature failures. There are commonly used methods by which residual stresses are currently measured. But these methods have a little damage and other problems; therefore, a new experimental technique has been devised to measure residual stress in materials with a combination of electronic laser interferometry, laser heating and finite element method. The electronic laser interferometer measures in-plane deformations while the laser heating and cooling provides for very localized stress relief. FEM is used for determining the heat temperature and other parameters. The residual stresses are determined by the amount of strain that is measured subsequent to the heat-up and cool-down of the region being interrogated. A simple model is presented to provide a description of the method. In this paper, the ambiguity problem for the fringe patterns has solved by a phase shifting method.