In this paper, multi-material auxetic lattice structures are designed through a density-based topology optimisation algorithm relying on purely geometric entities. Specifically, the approach presented in this paper is based on: (1) non-uniform rational basis spline (NURBS) entities to represent the distribution of each material phase within the design domain of the representative volume element (RVE) of the lattice structure, (2) an enhanced multiphase material interpolation scheme to penalise the stiffness tensor of the generic element of the finite element model of the RVE, (3) a numerical homogenisation method based on strain energy equivalence to calculate the macroscopic elastic constants of the lattice structure. In this background, a dedicated functional, accounting for auxeticity, axial and shear stiffness of the lattice structure, is proposed. The effectiveness of the method is proven on 2D and 3D benchmark problems. Particularly, the properties of NURBS entities are exploited to satisfy the requirement on the minimum length scale without introducing explicit constraints in the problem formulation. The effect of the problem formulation, of the ratio of the elastic properties of the constitutive phases, and of the initial guess on the optimised topologies are investigated. Optimised multi-material auxetic lattice structures are obtained by considering different elastic symmetries, including the most general triclinic (i.e., anisotropic) case. Finally, a sensitivity analysis of the optimised solution to the integer parameters of the NURBS entity is conducted.
Environmental protection and sustainable development remain key concerns for all stakeholders. In this context, hydrogen has emerged as a particularly promising energy vector for electricity and heat generation, contributing to the transition toward clean energy solutions. However, the refueling of high-pressure hydrogen tanks can lead to a rapid increase in the internal temperature of the storage cylinder, potentially causing a decrease in the state of charge, damage to tank walls, and, ultimately, safety concerns. This paper provides a detailed review of hydrogen storage technologies, with a particular focus on Type IV tanks for automotive applications. These tanks, characterized by a polymer liner fully wrapped in carbon fiber composites, are pivotal for achieving high-pressure containment while maintaining lightweight properties. To understand and address critical challenges, the study conducts an in-depth examination of the mechanical behavior and failure mechanisms of laminated composites across multiple scales. Through advanced multiscale characterization methods, including infrared thermography, X-ray tomography, acoustic emission, and digital image correlation, the research investigates how these materials respond under impact and cyclic loading conditions. Key failure mechanisms, such as matrix cracking, fiber breakage, and delamination, are explored to elucidate their progressive development and impact on the structural integrity of composites. The study also examines residual properties following dynamic loading to provide a comprehensive understanding of long-term performance under real-world conditions. Findings emphasize the importance of multiscale coupling from macro to microstructure to achieve accurate modeling and prediction of composite behavior. Insights from this research aim to optimize the design and durability of hydrogen storage systems, enabling safer and more efficient implementation in the automotive sector. This review concludes by summarizing the implications of these findings for enhancing the performance and safety of high-pressure hydrogen storage technologies.
NiTi alloys fabricated by laser powder bed fusion (LPBF) additive manufacturing technology not only address the compositional instability resulting from complex processes but also solve the challenges of difficult machining of intricate aerospace structures. However, there are very few reports on the wear behavior of LPBF-NiTi alloys. In the present work, the effects of microstructure and thermal treatment, including heat treatment and frictional heat, on the wear behavior of LPBF-NiTi alloy and 100Cr6 ball were analyzed through a series of tribological experiments with different sliding speeds. As the average sliding speed increases (0.079-0.216 m/s), the wear rate of the as-built and heat-treated samples tends to decrease in the range of 2.69 × 10−3- 0.97 × 10−3mm3/m. Although the heat-treated LPBF-NiTi alloy is 46% harder than the as-built alloy is, the latter has a higher toughness (505 MJ/m3) and greater transformation strain of SIM (0.097). This leads to a coupling effect of heat treatment and sliding speed on the wear resistance. In addition, the wear track morphologies under different sliding speeds are asymmetric due to the 24% greater acceleration at the far end from the motor and the 2.15 mm deviation between the maximum speed position and the geometric center of the track. The wear modes of the as-built and heat-treated samples included adhesive, abrasive and delamination wear. Moreover, the wear morphologies and dominant wear modes change with the frictionally caused heat release induced by the sliding speed.
We present a novel elasticity-inspired data-driven Fourier homogenization network (FHN) theory for periodic heterogeneous microstructures with square or hexagonal arrays of cylindrical fibers. Towards this end, two custom-tailored networks are harnessed to construct microscopic displacement functions in each phase of composite materials, based on the exact Fourier series solutions of Navier’s displacement differential equations. The fiber and matrix networks are seamlessly connected through a common loss function by enforcing the continuity conditions, in conjunction with periodicity boundary conditions, of both tractions and displacements. These conditions are evaluated on a set of weighted collocation points located on the fiber/matrix interface and the exterior faces of the unit cell, respectively. The partial derivatives of displacements are computed effortlessly through the automatic differentiation functionality. During the training of the FHN model, the total loss function is minimized with respect to the Fourier series parameters using gradient descent and concurrently maximized with respect to the adaptive weights using gradient ascent. The transfer learning technique is employed to speed up the training of new geometries by leveraging a pre-trained model. Comparison with finite-element/volume-based unit cell solutions under various loading scenarios showcases the computational capability of the proposed method. The utility of the proposed technique is further demonstrated by capturing the interfacial debonding in unidirectional composites via a cohesive interface model.
With the aim of improving the lifespan of different steel tools by reducing their degradation, CrAlN nitride coatings were investigated. The CrAlN coatings were deposited on X38CrMoV5 steel substrates using the DC reactive magnetron sputtering process under various deposition temperatures between ambient temperature and 300 degrees C. The effects of deposition temperature were systematically explored: XRD, EDS, SEM, optical profilometer, contact angles, nanoindentation, and tribometry were carried out to establish the structural, mechanotribological, and wetting properties' relationship. Results show that the high deposition temperature promotes the growth of (200) CrN preferentially orientation with the appearance of AlN phase. As the deposition temperature increases, the contact angle of the CrAlN surface films changes to a higher hydropholicity and the hardness of the coatings gradually increases to reach a maximum value of 28.1 GPa. The main wear mechanisms of CrAlN coating deposited at 300 degrees C against Al6061 ball are a combination of abrasive and adhesive features. This coating also has the lowest friction coefficient (0.63) and wear rate (1.72 x 10-3 mm3/N.m). Indeed, the preferred deposition temperature of about 300 degrees C could effectively adjust the microstructure and improve the mechanical and tribological properties of CrAlN coatings, thereby indicating its potential as an effective coating material for the protection of X38CrMoV5 steel in industrial fields.