Alveolar bone defects following tooth loss, trauma, or pathology compromise implant placement and prosthetic rehabilitation, necessitating effective guided bone regeneration strategies. Therefore, it is of interest to compare the clinical and radiographic outcomes of platelet-rich fibrin (PRF) and resorbable collagen membranes in alveolar defect regeneration. Hence, forty patients were randomly allocated into PRF (n=20) and collagen membrane (n=20) groups, both combined with particulate bone graft, with evaluation of healing parameters and CBCT-based bone gain at baseline and 6 months. Both groups demonstrated significant bone regeneration, with slightly greater horizontal gain in the collagen group, while vertical gain and complication rates showed no statistically significant differences. PRF and collagen membranes exhibit comparable regenerative efficacy, with PRF offering additional advantages of autologous origin, cost-effectiveness, and enhanced soft tissue healing.
Post-operative pain after single-sitting pulpectomy in primary molars significantly affects children's treatment acceptance and subsequent behaviour. Therefore, it is of interest to compare hand versus rotary instrumentation in 80 children (4-9 years) requiring pulpectomy in mandibular primary molars (n=40 each). Pain was assessed using the Wong-Baker FACES scale at 6, 12, 24, 48, and 72 hours post-treatment, alongside analgesic consumption. Rotary instrumentation showed significantly lower pain scores at 6 hours (1.85±1.12 vs 3.20±1.45, p<0.001), 12 hours (1.42±0.98 vs 2.65±1.28, p<0.001), and 24 hours (0.78±0.72 vs 1.55±1.08, p<0.001). Rotary instrumentation reduces post-operative pain compared to hand files, establishing it as the preferred technique for single-visit pulpectomy in pediatric endodontics.
A BSTRACT Aims: To compare and evaluate the pulp volume of permanent molars involving endo-perio lesions (EPLs) versus healthy molars (without EPLs) in patients with type 2 diabetes mellitus (T2DM). Objectives: (1) To determine the pulp volume of teeth with EPL and diabetes mellitus (DM). (2) To determine the pulp volume of healthy molars and DM. (3) To compare and evaluate pulp volume in healthy teeth and teeth with EPLs in DM patients. (4) To evaluate the pulp volume of the tooth in all types of EPLs. (5) To compare and evaluate pulp volume of teeth in >50 years and <50 years of DM patients. Subjects and Methods: Thirty-two patients diagnosed with EPL in any one molar and contralateral healthy molar in the same patient with T2DM were included in the study and were divided into two groups: Group 1 (32) – EPL and Group 2 (32) without EPL. The pulp volume was checked, and cone-beam computed tomography scans were taken for all teeth. DICOM files were evaluated to analyze the pulp volume with the help of ITK-Snap software by an experienced radiologist. Statistical Analysis Used: Data were analyzed using the Statistical Package for the Social Sciences software version 20.0. An independent samples t -test was carried out to compare the pulp volume. Results: A statistically significant difference was present in the pulp volume of healthy and diseased teeth. The pulp volume was much higher in the control group. Conclusions: Within the limitations of the study, it can be concluded that pulp volume is reduced in patients with EPLs and T2DM.
Introduction: Polymethyl Methacrylate (PMMA) is widely used as the material of choice for denture base fabrication due to its favourable handling properties, aesthetics, and cost-effectiveness. However, its low fracture and impact resistance remains a major clinical limitation, often leading to denture failure. Reinforcement of PMMA with fibres such as aramid and glass has been proposed to enhance its mechanical properties. Aim: To compare the impact strength of conventional heat-cure PMMA denture base resin, PMMA-reinforced with aramid fibres, and PMMA-reinforced with glass fibres. Materials and Methods: This in-vitro experimental study was conducted at the Department of Prosthodontics, Maratha Mandal’s Nathajirao G. Halgekar Institute of Dental Sciences and Research Centre, Belagavi, Karnataka, India from a period of 6 month from June 2025 to December 2025. A total of 30 rectangular test specimens were prepared using preformed stainless-steel metal dies (50×10×3 mm) with a 45-degree notch at the center. The specimens were divided into three groups (n=10 each): Group A: Conventional heat-cure PMMA (control), n=10, Group B: PMMA-reinforced with aramid fibres (1% by weight) n=10, Group C: PMMA-reinforced with glass fibres, n=10. A monomer-polymer ratio of 1:2 by weight was used. After reaching the dough stage, the material was packed, processed at 73°C for 30 minutes, bench-cooled, and deflasked. The specimens were tested using an Izod impact strength testing machine with a load of 2.9 joules/m. Impact strength was recorded in joules and kJ/m². Statistical analysis was performed using One-way Analysis of Variance (ANOVA) for overall comparison and the Bonferroni Post-hoc test for intergroup comparison with p≤0.05 was considered statistically significant. Results: The highest impact strength was observed in Group B (aramid fiber reinforced PMMA), followed by Group C (glass fiber reinforced PMMA), and lowest in Group A (control). Statistically significant differences were observed between Group B and Group C (p<0.001) and between Group C and Group A (p =0.021). However, the difference between Group B and Group A was statistically insignificant (p = 0.199). Conclusion: Within the limitations of this in-vitro study, incorporation of 1% by weight aramid fibres into heat-cure PMMA significantly improved the impact strength compared to conventional PMMA. Fiber reinforcement, particularly with aramid fibres, can be considered a promising approach to enhance the fracture resistance of denture base resins.
Background : Dental caries is one of the most common chronic childhood diseases and many decayed teeth are left untreated, especially in underprivileged parts of the world. Silver diamine fluoride (SDF) is widely used in arresting carious lesions for pediatric or uncooperative patients, however, its tendency to induce tooth discoloration poses challenges for subsequent aesthetic restorations. In response, we have pioneered a revolutionary nanoparticle solution that merges silver nanoparticles with a synergistic metal oxide component, amplifying the antibacterial potential of silver while addressing discoloration concerns. Aims and Objectives : Evaluate the antimicrobial efficacy of the novel nanoparticle solution against Streptococcus mutans and compare the tooth discoloration potential with SDF. Materials and Methods : Test -1: Streptococcus mutans were treated with a novel nanoparticle solution (Group 1), SDF (Group 2) and distilled water as a control (Group 3). The antimicrobial effectiveness of each treatment was evaluated by measuring inhibition zones on agar plates. Test-2: Involving 30 extracted human teeth, Group 1 received SDF treatment while Group 2 had nanoparticle solution. Standard digital photographs were taken before/after treatment (immediate, 1 hour, 24 hours, 1 week, 2 weeks) for comparison using the CIELAB system. Results : In Test 1, the Novel Nanoparticle solution exhibited significant S. mutans inhibition. In Test 2, unlike Group 2's SDF causing tooth discoloration, the experimental nanoparticle solution demonstrated significantly lower tooth discoloration compared with 38% SDF. Conclusion : The future of dentistry is bound to be overwhelmed with nanotechnology. The newly formulated nanoparticle solution is one step closer to achieving an optimum agent that drives the balance of desirable properties and exemplifies the synergy of antimicrobial efficacy and aesthetics in our modern dental practice.