Zinc dialkyldithiophosphate (ZDDP), as the most prominent lubrication additive, forms tribofilms consisting primarily of zinc phosphate glasses containing sulfides. As sulfur is linked to environmental concerns, sulfur-free zinc phosphate coatings have been sputtered from a Zn3(PO4)2 target and investigated here. Based on the bridging to non-bridging oxygen ratio, determined by X-ray photoelectron spectroscopy (XPS), the as deposited coatings are classified as metaphosphates. As the annealing temperature is increased, the chain lengths are reduced, as witnessed by XPS data indicated by a loss of phosphorus and oxygen of the coating surface, likely due to hydrolysis with water from the atmosphere. Transmission electron microscopy energy-dispersive X-ray spectroscopy line scans show that the XPS-revealed composition change of the coating surface upon annealing occurs over the whole thickness of the coating. This alteration in composition and chain length reductions causes a rise in hardness, reduced Young's modulus, and wear resistance. Therefore, the properties of the artificial zinc phosphate tribofilms can be tailored via a thermally stimulated composition change, causing an alternation in chain length from meta- to orthophosphate and thereby enabling the design of coatings with desired mechanical properties.
In this work, we study the reaction-controlled dual bubbles ripening on a heterogeneous substrate with high surface wettability hysteresis, where the bubbles evolve with constant contact radius but varied contact angle. We first theoretically derived the governing kinetic equation of bubble curvature radius $R_B$ , based on which we surprisingly found three possible ripening processes under six different conditions, i.e. the classical Ostwald ripening (the bubble with the larger curvature radius $R_B$ exhibits an increase in $R_B$ , while the bubble with the smaller curvature radius $R_B$ experiences a decrease in $R_B$ ), the reversed ripening (converse to Ostwald ripening), and the consistent ripening ( $R_B$ of both bubbles increases or reduces consistently). Further analyses from the aspects of chemical potential and free energy lead to an interesting finding that the $R_B$ of two bubbles finally reach egalitarianism, independently of different ripening processes. Numerical results obtained from two-phase lattice Boltzmann modelling demonstrate excellent agreement with theoretical predictions, specifically concerning the kinetic equation, the various ripening processes, and the egalitarianism of bubble radii $R_B$ after ripening completion.
Reservoir heterogeneity is a great challenge for CO2 Enhanced Oil Recovery (EOR), causing early breakthrough and a restricted swept area. The successful application of CO2 EOR in mature fields requires development of high-resolution geological models. Therefore, a field-scale calibration of a three-phase compositional model, incorporating multiphase production data, is necessary. The calibration workflow follows a two-stage process: global and local. In the global stage, field target rates and average pressure behavior are matched by adjusting permeability. The focus of this paper is the local stage, where the updated permeability field from the global step is further refined at cell level by a streamline-based Generalized Travel-Time Inversion (GTTI) to match well-level historical water cut (WCT) and gas oil ratio (GOR) simultaneously. The proposed method is applied to a mature field in West Texas, a compositional model with over one million active cells and 286 wells, across decades of production-injection history from primary depletion to tertiary recovery. Following the initial field constraints matching process, we achieve a satisfactory WCT matching during the waterflooding period. Subsequent fine calibration, conducted via the streamline-based method, primarily focuses on the CO2 EOR period under complex well schedules, including well conversions between producer to injector, shut-in, and reopening. Furthermore, utilizing cumulative gas production (GPT) instead of GOR for the estimation of the best time shift required for GTTI serves to eliminate the influence of high frequency changes and well shut-in periods. This approach enhances the inversion process, as GTTI performs best with continuous and monotonic production histories.
Time-Lapse (4D) seismic data offers a comprehensive spatial view of reservoir, while production data provides localized insights from individual wells. Both of them are essential for understanding reservoir heterogeneity, monitoring fluid movements, and improving reservoir management strategies. This study presents an effective and efficient integration approach that combines seismic and production data using streamline for heterogeneous geologic models. In the proposed approach, water saturation change (dSw) is considered as the matching objective for 4D data integration, while water cut (WCT) is treated as the matching goal for production data integration. A commercial finite-difference flow simulator is used for reservoir simulation to generate time-dependent velocity fields, from which streamlines are computed. The sensitivities of dSw and WCT to absolute permeability at individual grid are computed by efficient analytical streamline techniques. Finally, the sparse-least-square-regression method is used to minimize the misfit between simulation results and observed data by tuning the permeability field at the cell level. Practical feasibility of the proposed approach is demonstrated using a 2D synthetic case and applied to SPE benchmark Brugge field case. In both cases, three scenarios are discussed: 1) model calibration using production data only; 2) model calibration using 4D data only; 3) model calibration using both production and 4D data simultaneously. These scenarios investigate the improvements in estimating permeability distribution, water saturation evolution, and production data responses. The advantages of incorporating time-lapse variations are highlight by identifying the spatial continuity of reservoir heterogeneity, while the addition of production data ensures practical applicability by aligning the model with observed production behavior. The proposed method provides the theoretical basis and a practical framework for the integration of production and 4D data into heterogeneous geologic models.
Additive manufacturing has a significant role in the development of medical devices. Artificial hip and knee joints are two examples of 3D‐printed models that have revolutionized medicine. This work presents the 3D‐printed model designed according to the dog's leg peculiarities. The goal is to use this 3D model developed in order to manufacture a medical device that monitors specific parameters regarding a dog's articulation state of health. By using this approach, unnecessary animal testing can be avoided, thus reducing the ethical concerns associated with such practices. The monitoring device will integrate multiple sensors, such as temperature, vibration, and humidity sensors. The device will also feature a data transmission module to enable the storage of collected patient data in a database. The modeling and simulation parameters used to make the 3D model are presented in addition to the architecture of the monitoring device. Also, the time, material costs, and layer thickness are parameters that will be discussed in the paper.