
In order to take away the heat of superconducting cavity and discard the complex liquid helium system by relying only on cryocoolers and heat conduction,the conduction cooling structure of the superconducting cavity was studied.According to the heat transfer requirements,five different cooling structures were preliminarily designed for the 650MHz superconducting cavi-ty,and the heat transfer simulation software was used to simulate the heat transfer,and the influ-ence of different cooling structures,cooling structure materials and contact thermal resistance on the cooling effect was studied.The results show that it is more reasonable to design three cold heads than two cold heads.The length of the thermal link connecting the cold head and the cold ring is approximately linear with the temperature of the superconducting cavity,and the thermal link at the beam tube is conducive to cutting off the heat leakage of the beam tube.The cooling effect of the thermal link material using high-purity aluminum is better than that of high-purity ox-ygen-free copper,and the contact thermal resistance between the thermal link and the cold ring should be controlled below 10 K·cm2/W.
To enhance the freezing properties of droplets,droplet containing silica nanoparti-cles were used,the impact of varying concentrations of SiO2 nanoparticles(5 mg/mL,10 mg/mL,30 mg/mL,50 mg/mL)and different cold surface temperatures(268 K,265 K,263 K)on droplet freezing characteristic(droplet deformation,contact angle,and freezing time)was investigated.The results showed that the freezing time of silica droplets(SiO2-H2O)is affected by the degree of su-percooling and the content of SiO2 nanoparticles.At low supercooling temperature(263 K),10 mg/mL SiO2-H2O accelerates freezing by 34.78%,but at high supercooling temperature(265 K and 263 K),5 mg/mL SiO2-H2O shows delayed freezing by 21.2%and 36.84%,respectively.In addition,SiO2 nanoparticles can intensify the opacification of the initial droplets and reduce the release of bubbles inside the frozen droplets according to the deformation characteristics of the droplets.The interaction between SiO2 nanoparticles and the solid-liquid phase interface cause the longitudinal change rate to be reduced,and the transverse deformation to be enhanced.The drop-lets are more rounded in profile when freezing was completed.
To meet the heat dissipation performance needs of the domain controller chips and the lightweight design requirements of the heat sink simultaneously,a natural convection heat dissi-pation scheme was designed based on the chimney effect.The influence of fin thickness,fin spac-ing,fin height and chimney height on heat dissipation performance was explored based on univariate variable method.The results show that the airflow velocity at the fin air inlet can be significantly el-evated by the introduction of chimney effect,which result in the improvement of the natural heat dis-sipation effect.At the same time,the quality of the radiator and material cost can be reduced.Fur-thermore,the central composite design method was used to construct the response surface for multi-objective optimization design,and the optimal parameter of chimney heat sink was obtained.
In order to study the shear strength characteristics and the ontological relationship of peaty soils,the changes in mechanical properties and the ontological relationship of frozen peaty soils for different freezing temperatures were analyzed based on the indoor triaxial testing equip-ment by taking soils on site.The analysis results show that the damage pattern of frozen remodeled peaty soil changes with the increase of water content,and the plastic change is transformed into brittle change characteristics.The bias stress-strain curve of Kunming Dianchi remodeled peaty soil shows strain-hardening type,and the peak bias stress chang significantly when changing the influencing factors(water content,enclosing pressure,freezing temperature),and the trend of change is linear.The angle of internal friction and cohesion of frozen remodel peat mass with freezing temperature of-5 ℃ and water content of 49%were found at different peripheral pres-sures,which were 121.91 kPa and 29.17°respectively.Parameter of frozen Dianchi remodel peaty soil were measured based on the Duncan-Zhang model and considering different influencing factors(water content,enclosing pressure,freezing temperature),and relevant constitutive models were established under different influencing factors.The theoretical values of the present constitutive model were compared with the actual test values to verify the reasonableness of the present consti-tutive model,and the damage ratio values of frozen remodeled peaty soil were calculated to be in the range of 0.817-0.922,which made the present constitutive model more reliable.
In order to study the problem of along-plane discharge under liquid nitrogen im-pregnation,the along-surface flashover voltage of polytetrafluoroethylene in extremely inhomoge-neous electric fields in liquid nitrogen was measured.The result showed that the along-surface flashover voltage under positive polarity pulse is generally higher than that in negative polarity.Through the analysis of the flash traces,combined with the simulation of electric field distribution and the theoretical study of the along-surface flash mechanism in liquid nitrogen,the reason why the polarity effect of flashover along the surface in liquid nitrogen environment is opposite to that of transformer oil is that the low temperature of liquid nitrogen medium is extremely easy to vaporize,the formation of vaporization layer is easier in the flash process,and the degree of spatial ionization of liquid nitrogen medium is much smaller than that of nitrogen in the gasification layer.