
. The PLC is widely used as a controller with input in the form of switches and sensors and output in the form of coils. PLC can be connected with HMI to facilitate the operation of the PLC. The usual HMI is installed on a PLC in the form of a stand-alone PC HMI and HMI that is connected via serial cable or Ethernet cable. The HMI in the form of wireless is rarely found. In this paper, will show the use of HMI connected with Bluetooth (BT) on the Outseal PLC (locally made PLC). The PLC is programmed with standard ladder diagram. Selector 4 channels with input in the form of switches and output in the form of coils (lights). Lights can be selected via the switch. Difficulties in the PLC with input using the switch are not easily changed from afar. HMI designed has facilities available for ALL OFF, ALL ON and TOGGLE mode. The HMI uses a smart phone with HMI modbus apk for android. The Smart phone screen can be used as a monitor and is a touch screen for input. Screen size of 5.5 inch, pixel size of 720 1280 is capable of displaying 7 switches and 4 indicators
In this research, the design of close loop BLDC motor speed control was designed with several simulation test conditions and also discuss the differences of boost converter with Fuzzy control and boost converter without Fuzzy control. The BLDC motor specifications used in this research are 3 phase, constant voltage is 80 V_peak L-L / krpm and the moment of inertia is 0.000553 J (kgm2). The specifications of the solar were Canadian CS5T 130M with a maximum power=129W. The test results on the boost converter without using Fuzzy controls have fluctuating voltages. Whereas when using PID controls, the output voltage is stable and the voltage is±100 V. In simulation, PID control circuits have THD values amounting to 3.12%, which corresponds to the standards specified by IEEE for voltages below 1 kV=<5%. The simulation test results with several conditions have made a difference in the results of the motor speed response. Based on the results of the simulation test, it is known that the speed control with the PID control circuit has better results compared to the open loop circuit.
Biodiesel has chemical and physical properties similar to petroleum diesel so that it becomes one of the alternative energies. In this research, biodiesel was produced with esterification and transesterification reactions by assisted zirconia catalyst. Zirconia catalyst was prepared from zirconia sand as natural resources in Indonesia. Th physical and chemical process was used in preparation of catalyst. The catalyst was characterized with XRD and SEM anaysis. Zirconia catalysts used have tetragonal crystal structure and are amfortable. Biodiesel production is carried out at 60 C with simultaneous transesterification esterification. Analysis of changes in chemical structure and formation of FAME were analyzed using GC-MS. The results of this study are the greater the percent weight added, the higher the value of FAME and the lower biodiesel obtained has density, viscosity and FFA contents. Biodiesel product was similar with SNI of biodiesel.
In an attempt to reduce the number of casualties when natural disasters occurred, the existence of reliable disaster response is becoming urgency. Nevertheless, earlier references in disaster management field are rarely discussing this importance issue. In narrowing down this research gap, in this paper we presented a framework in designing anticipatory Failure Mode and Effect Analysis (FMEA) in preparing anticipatory action preventing derailment of humanitarian response operation. An introduction and procedures to implement anticipatory failure mode and effect analysis is presented using case example. The result of applying the model enable to indicate potential riskiest failure to be alleviated. Potential research opportunities from this study are also presented.
The traditional motifs on the official uniforms of the Sragen District Civil Servants that have been used today are less attractive to users. The selection of uniform motifs does not consider consumer preferences. This study aims to develop traditional textile motifs based on consumer preferences. Consumer preferences are collected, and changed to technical requirements. Then, discover which of the components have the biggest impact on meeting the product design requirements and determine the desired component specifications to be implemented by the goyor woven SMEs in Sukoharjo. The application of design engineering uses Quality Function Deployment (QFD) level 2 in form of House of Quality (HOQ) and uses the Operating Process Chart (OPC) to identify the parts needed. The HOQ of QFD Level 2 matrix gives information about critical component and the priority of the critical component, also determine the desired component specifications. The critical components that have impacted the most on meeting the design requirement are weft thread (benang pakan) and warp thread (benang lusi). Weft threads and warp threads use the rayon thread with a size of 42/2. The second priority is the proportion of motifs. The proportion of motifs made with a size of 10-15 cm with a distance between motifs no more than 1 cm.