Filter-based spectral systems are highly competitive due to their compactness, simplicity, and well-defined spectral characteristics. However, their primary drawback remains low detection efficiency. This work explores various strategies to enhance detection efficiency. While an additional row of beamsplitters can significantly improve illumination, alternative folded beam path designs—eliminating the need for beamsplitters—prove to be far more effective. Additionally, a novel approach utilizing a freeform mirror is introduced, enabling differential adjustment of detection efficiency across different spectral regions. For the first time, a comprehensive comparison of these strategies is presented.

To accurately model the specific detection characteristics of spectral sensors based on linear variable filters (LVFs) within an optical design tool, it is essential to consider crucial position-variable spectral properties, such as peak transmittance, central wavelength, half width, or slope steepness. In this context, we propose a straightforward approach, integrating a dynamic link library (DLL) containing all position-dependent spectral properties of the LVF into a commercial optical design software. Exemplary investigations are conducted for an LVF with a detection range of 450-850 nm. For ease of use, the measured position-, wavelength-, and angle-dependent transmission properties of the LVF have been described through a simple yet highly accurate model system. Moreover, to highlight the essential value of this simulation for specific applications, an efficiency-enhancing spectral module is simulated, which is an LVF-mirror arrangement characterized by a multiple-reflected beam path. The introduced optical design tool demonstrates its particular strength by enabling the optimization of the highest detection efficiency for either the short- or long-wavelength range. (c) 2024 Optica Publishing Group under the terms of the Optica Open Access Publishing Agreement

This study demonstrates the concept of an angle-variable compact spectral module. As a key feature, the filter-based module enables highly efficient wavelength-selective light detection by applying the reflective beam path according to the origami example. It was accomplished through inclined mirrors, which allow for different incident angles on the wavelength separating interference filters used in a robust assembly with no moving parts. To experimentally verify the concept, a wavelength range between 550 and 700 nm was detected by 11 spectral channels. These initial results showed the potential to develop easily scalable and application-tailored sensors, which can overcome conventional filter-based sensor approaches that use upright or fixed-angle illumination.

Filter-based spectral detectors convince with their simple concept, an extremely compact and robust design and the possibility to adapt the addressed spectral range and the resolution to the individual application requirements. Unfortunately, these filter-based sensors usually suffer from low detection efficiency. In this contribution we discuss and compare different methods that allow to substantially increase the detection efficiency of filter-based spectral sensors. An initial concept is based on a wavelength-dependent redistribution of the incident light before it reaches the individual filter elements of the array. This approach allows a substantial increase in detection efficiency, but requires additional dichroic elements in the beam path. An alternative approach uses a folded beam path architecture and completely waives additional dichroic elements. This approach is not only suitable for filter-based spectral sensors, but can also be transferred to increase the efficiency of hyperspectral imaging systems.

This paper demonstrates a method to significantly enhance the detection efficiency of filter-based spectral sensors without the use of additional dichroic optics for spectral preselection. The fundamental principle is that light reflected from one interference filter or filter segment can be used consecutively, reducing the overall system losses. The proof-of-concept is presented using two compact optical modules. The first module uses 10 individual filters between 520 and 800 nm, and the second is capable of continuous spectrum acquisition between 450 and 825 nm using a linear variable filter (LVF) as a key element. An efficiency increase factor of up to approximately 100 compared to a common system, where the entire LVF is directly illuminated, was demonstrated.

Optical interferometric sensors have acquired significant importance in metrology and information technology, especially in terms of their potential application in launching size, selectivity, sensitivity, resolution, spectral tuning ranges, efficiency, and cost. However, these demands are often contradictory and counteract one another, and are thus difficult to simultaneously fulfill during their interaction. This review focuses on a detailed comparison of seven different strongly miniaturized sensor concepts investigating the limits of these demands. For the visible and near-infrared spectral range, seven optical sensors were reviewed based on the following methodologies: classical optical transmission and reflection gratings, arrayed waveguide gratings, static Fabry–Pérot (FP) filter arrays, MEMS tunable FP interferometers, MEMS tunable photonic crystals, plasmonic filters, and fiber tip sensors. The comparison between the selected concepts concentrates on (i) the minimum space required for a particular spectral range, (ii) resolution, (iii) the integration in optical fiber technology, (iv) tunability to save space, (v) efficiency in using available light, (vi) multiplexing, (vii) miniaturization limits, and (viii) the potential of nanoimprint for cost reduction. Technologies for enhancing efficiency to obtain more available light and their applicability to the different methodologies were studied.

Optical spectrometers and sensors have gained enormous importance in metrology and information technology, frequently involving the question of size, resolution, sensitivity, spectral range, efficiency, reliability, and cost. Nanomaterials and nanotechnological fabrication technologies have huge potential to enable an optimization between these demands, which in some cases are counteracting each other. This paper focuses on the visible and near infrared spectral range and on five types of optical sensors (optical spectrometers): classical grating-based miniaturized spectrometers, arrayed waveguide grating devices, static Fabry–Pérot (FP) filter arrays on sensor arrays, tunable microelectromechanical systems (MEMS) FP filter arrays, and MEMS tunable photonic crystal filters. The comparison between this selection of concepts concentrates on (i) linewidth and resolution, (ii) required space for a selected spectral range, (iii) efficiency in using available light, and (iv) potential of nanoimprint for cost reduction and yield increase. The main part of this review deals with our own results in the field of static FP filter arrays and MEMS tunable FP filter arrays. In addition, technology for efficiency boosting to get more of the available light is demonstrated.

A method to drastically enhance detection efficiency of a linear variable filter (LVF) sensor across an extended and continuous wavelength range is presented. The efficiency is increased by a wavelength preselection concept, where the incoming light is divided into partial spectra to reduce otherwise unavoidable reflection losses of filter-based spectrometers. The simple but effective setup uses selected and successively arranged dichroic beamsplitters, which ensures an optimized compromise between efficiency enhancement and minimum increasing complexity. When connected to a two-dimensional camera and combined with a tilted LVF, this compact optical system allows the continuous recording of the full wavelength range between 450 and 850 nm with a resolution of similar to 19 nm at 508.6 nm. An efficiency enhancement factor of up to 5.7 is achieved in comparison to a conventional LVF setup. The working principle was verified by measuring the reflection spectra of different natural and artificial green leaves. The proposed approach for increasing the efficiency can be miniaturized and applied to a broad range of other filter-based sensors. (C) The Authors. Published by SPIE under a Creative Commons Attribution 4.0 International License.

A method that significantly increases the detection efficiency of filter array-based spectral sensors is proposed. The basic concept involves a wavelength-dependent redistribution of incident light before it reaches the filter elements located in front of the detector. Due to this redistribution, each filter element of the array receives a spatially concentrated amount of a pre-selected and adjusted spectral partition of the entire incident light. This approach can be employed to significantly reduce the reflection and absorption losses of each filter element. The proof-of-concept is demonstrated by a setup that combines a series of consecutively arranged dichroic filters with Fabry–Perot filter arrays. Experimentally, an efficiency increase by a factor larger than 4 compared to a reference system is demonstrated. The optical system is a non-imaging spectrometer, which combines the efficiency enhancement module with the filter arrays, is compact ( 17.5 m m × 17.5 m m × 7.8 m m ), and integrated completely inside the CCD camera mount.