Recent developments to the M3D-C1 code enable higher fidelity modeling of disruptions, and can be applied in the design verification of reactor-scale tokamaks. Among these new capabilities is a method to mesh conducting vessel structures such as coils and passive plates, packing of the toroidal mesh around gas injectors, as well as anisotropic resistivity inside the vessel structures. We present extended-magnetohydrodynamic (MHD) simulations of disruption mitigation via massive gas injection (MGI) in SPARC. The goal of this study is to inform the disruption mitigation layout of SPARC and aid in the design of an effective gas injector configuration. Fully three-dimensional simulations with M3D-C1 are carried out for various injector configurations with the primary goal of determining the effect of different MGI parameters on heat loads and vessel forces. The simulations include a model for impurity ionization, recombination, advection and radiation, as well as spatially resolved conducting structures around the plasma. A localized mixture of deuterium and neon with a small toroidal and poloidal width is injected in up to six locations. We demonstrate that M3D-C1 can model a rapid shutdown via MGI using narrow and more realistic gas plumes than in previous simulations. As a result of the q = 1 surface in the SPARC baseline case a sawtooth is observed early in the simulations. Despite the sawtooth and the onset of edge MHD instabilities, the impurity distribution remains localized around the injector locations, but enables a radiative shutdown of the plasma. We find that using the maximum of six gas injectors results in a lower peaking factor and leads to a more even distribution of radiation toroidally than using two injectors.

Diffusive transport processes in magnetized plasmas are highly anisotropic, with fast parallel transport along the magnetic field lines sometimes faster than perpendicular transport by orders of magnitude. This constitutes a major challenge for describing non-grid-aligned magnetic structures in Eulerian (grid-based) simulations. The present paper describes and validates a new method for parallel diffusion in magnetized plasmas based on the anti-symmetry representation [Halpern and Waltz, Phys. Plasmas 25, 060703 (2018)]. In the anti-symmetry formalism, diffusion manifests as a flow operator involving the logarithmic derivative of the transported quantity. Qualitative plane wave analysis shows that the new operator naturally yields better discrete spectral resolution compared to its conventional counterpart. Numerical simulations comparing the new method against existing finite difference methods are carried out, showing significant improvement. In particular, we find that combining anti-symmetry with finite differences in diagonally staggered grids essentially eliminates the so-called "artificial numerical diffusion" that affects conventional finite difference and finite volume methods.

In 2021 JET exploited its unique capabilities to operate with T and D-T fuel with an ITER-like Be/W wall (JET-ILW). This second major JET D-T campaign (DTE2), after DTE1 in 1997, represented the culmination of a series of JET enhancements-new fusion diagnostics, new T injection capabilities, refurbishment of the T plant, increased auxiliary heating, in-vessel calibration of 14 MeV neutron yield monitors-as well as significant advances in plasma theory and modelling in the fusion community. DTE2 was complemented by a sequence of isotope physics campaigns encompassing operation in pure tritium at high T-NBI power. Carefully conducted for safe operation with tritium, the new T and D-T experiments used 1 kg of T (vs 100 g in DTE1), yielding the most fusion reactor relevant D-T plasmas to date and expanding our understanding of isotopes and D-T mixture physics. Furthermore, since the JET T and DTE2 campaigns occurred almost 25 years after the last major D-T tokamak experiment, it was also a strategic goal of the European fusion programme to refresh operational experience of a nuclear tokamak to prepare staff for ITER operation. The key physics results of the JET T and DTE2 experiments, carried out within the EUROfusion JET1 work package, are reported in this paper. Progress in the technological exploitation of JET D-T operations, development and validation of nuclear codes, neutronic tools and techniques for ITER operations carried out by EUROfusion (started within the Horizon 2020 Framework Programme and continuing under the Horizon Europe FP) are reported in (Litaudon et al Nucl. Fusion accepted), while JET experience on T and D-T operations is presented in (King et al Nucl. Fusion submitted).

The next generation of large tokamaks, including ITER, will be equipped with a disruption mitigation system (DMS) that can be activated if a disruption is deemed to be imminent. Introducing impurities by pellet (large or shattered) or massive gas injection has been shown to be an effective mitigation mechanism on many tokamaks. The goal of the mitigation is to lessen the thermal and electromagnetic loads from the disruption without generating enough high-energy (runaway) electrons to damage the device. Variations of this mitigation process with impurity injection are presently being tested on many experiments. We have modeled one such impurity injection experiment on DIII-D using the M3D-C1 nonlinear 3D extended MHD code (Jardin et al 2012 Comput. Sci. Discovery 6 014002), The model includes an argon large pellet injection and ablation model, impurity ionization, recombination, and radiation, and runaway electron formation and subsequent evolution, including both Dreicer and avalanche sources. We obtain reasonable agreement with the experimental results for the timescale of the thermal and current quench and for the magnitude of the runaway electron plateau formed during the mitigation. This is the first 3D full MHD simulation with pellets and REs to simulate the disruption process and it also provides a partial validation of the M3D-C1 DMS model.

In ITER, pellets are calculated to require more than 8 times the mass than currently planned to reliably trigger edge-localized modes (ELMs). Unmitigated heat flux impulses from ELMs are intolerable in ITER at full power and current. Therefore, ITER operation relies on multiple approaches to control ELM heat fluxes. One method is pellet ELM pacing to instigate small rapid ELMs with low heat flux. Predicting the performance of pellet pacing is critical for ITER, which is expected to operate in a regime with a low-collisionality, peeling-limited pedestal. However, to trigger ELMs the local pressure increase in the expanding pellet cloud pushes the equilibrium over the ballooning stability limit. In this work, linear and nonlinear M3D-C1 simulations are used to predict pellet mass thresholds in DIII-D discharges and ITER scenarios with peeling-limited pedestals. It is found that the distance of the equilibrium's operational point from the ballooning branch of the pedestal stability boundary strongly changes thresholds. Linear M3D-C1 simulations find a strong dependence of the pellet mass threshold on the poloidal injection location for ITER's 15 MA, Q = 10 scenario. The required pellet mass at the planned injection locations is 8 to 17 times larger than currently considered. However, such linear simulations do not include pellet ablation physics or time evolution of density and temperature. A new scheme of 2D nonlinear simulations, coupled with linear stability analysis at various steps throughout the nonlinear time evolution, was developed to include such physics and improve on the linear results. These new nonlinear-to-linear simulations confirm previous findings. This result suggests that pellet ELM triggering in ITER could require pellets much larger than those currently planned, which makes ELM-pacing operationally challenging. On the other hand, fueling pellets injected from the high-field side will likely not unintentionally trigger ELMs in an otherwise ELM-stable plasma.

The DIII-D tokamak has elucidated crucial physics and developed projectable solutions for ITER and fusion power plants in the key areas of core performance, boundary heat and particle transport, and integrated scenario operation, with closing the core-edge integration knowledge gap being the overarching mission. New experimental validation of high-fidelity, multi-channel, non-linear gyrokinetic turbulent transport models for ITER provides strong confidence it will achieve Q 10 operation. Experiments identify options for easing H-mode access in hydrogen, and give new insight into the isotopic dependence of transport and confinement. Analysis of 2,1 islands in unoptimized low-torque IBS demonstration discharges suggests their onset time occurs randomly in the constant beta phase, most often triggered by non-linear 3-wave coupling, thus identifying an NTM seeding mechanism to avoid. Pure deuterium SPI for disruption mitigation is shown to provide favorable slow cooling, but poor core assimilation, suggesting paths for improved SPI on ITER. At the boundary, measured neutral density and ionization source fluxes are strongly poloidally asymmetric, implying a 2D treatment is needed to model pedestal fuelling. Detailed measurements of pedestal and SOL quantities and impurity charge state radiation in detached divertors has validated edge fluid modelling and new self-consistent 'pedestal-to-divertor' integrated modeling that can be used to optimize reactors. New feedback adaptive ELM control minimizes confinement reduction, and RMP ELM suppression with sustained high core performance was obtained for the first time with the outer strike point in a W-coated, compact and unpumped small-angle slot divertor. Advances have been made in integrated operational scenarios for ITER and power plants. Wide pedestal intrinsically ELM-free QH-modes are produced with more reactor-relevant conditions, Low torque IBS with W-equivalent radiators can exhibit predator-prey oscillations in T-e and radiation which need control. High-beta(P) scenarios with q(min) > 2, q(95)-7.9, beta(N) > 4, beta(T)-3.3% and H-98y2 > 1.5 are sustained with high density ((n) over bar = 7E19 m(-3), f(G)-1) for 6 tau(E), improving confidence in steady-state tokamak reactors. Diverted NT plasmas achieve high core performance with a non-ELMing edge, offering a possible highly attractive core-edge integration solution for reactors.

The Fusion Synthesis Engine (FUSE) is a state-of-the-art software suite designed to revolutionize fusion power plant design. FUSE integrates first-principle models, machine learning, and reduced models into a unified framework, enabling comprehensive simulations that go beyond traditional 0D systems studies. FUSE's modular structure supports a hierarchy of model fidelities, from steady-state to time-dependent simulations, allowing for both pre-conceptual design and operational scenario development. This framework accelerates the design process by enabling self-consistent solutions across physics, engineering, and control systems, minimizing the need for iterative expert evaluations. Leveraging modern software practices and parallel computing, FUSE also provides multi-objective optimization, balancing cost, efficiency, and operational constraints. Developed in Julia, FUSE is fully open-source under the Apache 2.0 license, promoting transparency and collaboration within the fusion research community.

Experiments on the DIII-D tokamak demonstrate that edge localized mode (ELM) stability can be manipulated using localized electron cyclotron current drive (ECCD) in conjunction with resonant magnetic perturbations (RMPs). The injection of counter-plasma-current edge ECCD reduces the RMP amplitude required to suppress ELMs and bifurcates the pedestal into a high-confinement regime with 7 kPA pedestal pressure. This is the first time such a high confinement regime has been accessed through the bifurcation from the ballooning stability branch predicted by existing models. These observations are consistent with modeled ECCD manipulation of magnetic islands induced by the RMPs.

We use the 3D magnetohydrodynamic (MHD) code M3D-C1 [Jardin et al., Comput. Sci. Discovery 5, 014002 (2012)] to examine the MHD stability and subsequent evolution of NSTX shot 129169. This discharge had a period with a non-monotonic safety factor profile, q (reversed shear), which was terminated by a MHD event that abruptly lowered the central safety factor, q0, and greatly reduced the peakedness of the pressure profile. We show that the equilibrium just before the MHD event occurred was linearly unstable to many pressure-driven infernal modes. Modes with toroidal mode number n≥3 all had rational surfaces very close to the minimum value of q. However, a non-resonant pressure-driven (1, 1) mode was also present, and this dominated the nonlinear evolution. The final state in the simulation, after the MHD activity subsided, had a reduced and flattened pressure profile and a nearly monotonic q-profile, in qualitative agreement with experimental results. The initial state was also unstable to the resistive interchange criteria in the reversed-shear region, but the final state was stable everywhere. The “double tearing mode” (DTM) does not appear to play a role in the MHD activity of this discharge. In Appendix A, we show that in a torus, the DTM is strongly stabilized by pressure, but it is destabilized in cylindrical geometry (which has been the most extensively analyzed in the literature).

This paper deals with resistive wall tearing mode (RWTM) disruptions. RWTMs are closely related to resistive wall modes (RWMs). The nonlinear behavior of these modes is strongly dependent on the resistive wall outside the plasma. A conducting wall is highly mitigating for RWTM disruptions. The consequence for ITER, which has a highly conducting wall, is that the thermal quench (TQ) time could be much longer than previously conjectured. Active feedback stabilization is another possible way to mitigate or prevent RWTM disruptions. Simulations of disruptions are reviewed for DIII-D and MST. MST has a longer resistive wall time than ITER, and disruptions are not observed experimentally when MST is operated as a standard tokamak. Simulations indicate that the RWTM disruption time scale is longer than the experimental shot time. In general, edge cooling by tearing mode island overlap or by impurity radiation causes contraction of the current profile, which destabilizes RWTMs. The equilibria studied here have a q = 2 rational surface close to the edge of the plasma, and low edge current density. A sequence of low edge current model equilibria hasmajor disruptions only for a resistive, not ideal, wall, and approximately edge q < 3. This is consistent with typical regimes of tokamak disruption avoidance, suggesting that typical tokamak disruptions could be RWTMs.

This paper investigates the predictive capabilities of TGYRO and TGLF models in assessing the performance of negative triangularity (NT) plasmas compared to positive triangularity (PT) plasmas in fusion devices. TGYRO predicts kinetic profiles, while TGLF analyzes turbulent transport. The study reveals that TGYRO reasonably predicts NT profiles similar to PT, although it overpredicts the high-power scenarios where there is increased experimental MHD activity. TGLF analysis finds reduced linear growth rates in NT and altered flux spectra relative to PT. Additionally, the TGLF SAT0 saturation model is observed to predict high-k transport and a reduction of particle transport with the electron temperature gradient. These findings are further corroborated by core-pedestal modeling using the Stability Transport Equilibrium Pedestal workflow, showing stronger confinement improvements in NT, particularly at higher power densities for the SAT0 saturation model. The study underscores the importance of accurately capturing turbulence saturation mechanisms for NT in order to project its performance accurately in fusion reactors.

This report is in partial fulfillment of deliverable D1.1 Optimization of the SPI model and summarizes axisymmetric ITER SPI parameter scans performed by the NIMROD code for several ITER equilibria. These axisymmetric parameter scans are to assess the sensitivity of various injection parameters in preparation for 3D MHD SPI simulations. The scans are comprised of 5 scenarios: S1 - fragment size scan : 3 uniform pencil beam, 1 distributed size pencil beam S2 - velocity scan : v = [250,500,750]m/s S3 - velocity dispersion scan : dv/v = [0.2,0.4] (linear distribution) S4 - poloidal extent of plume : [15' ,45' ] (linear distribution) (dv/v=0.2) S5 - poloidal injection angle : +/-[20' ,45' ] (dv/v=0.2) These scans are performed with several ITER equilibria representative of the operating range, from low current and thermal energy (H123 5MA, 29MJ Hydrogen H-mode) to high current and high thermal energy (DT24 15MA, 370MJ D-T H-mode).

The STEP (Stability, Transport, Equilibrium, and Pedestal) integrated-modeling tool has been developed in OMFIT to predict stable, tokamak equilibria self-consistently with core-transport and pedestal calculations. STEP couples theory-based codes to integrate a variety of physics, including magnetohydrodynamic stability, transport, equilibrium, pedestal formation, and current-drive, heating, and fueling. The input/output of each code is interfaced with a centralized ITER-Integrated Modelling & Analysis Suite data structure, allowing codes to be run in any order and enabling open-loop, feedback, and optimization workflows. This paradigm simplifies the integration of new codes, making STEP highly extensible. STEP has been verified against a published benchmark of six different integrated models. Core-pedestal calculations with STEP have been successfully validated against individual DIII-D H-mode discharges and across more than 500 discharges of the H98,y2 database, with a mean error in confinement time from experiment less than 19%. STEP has also reproduced results in less conventional DIII-D scenarios, including negative-central-shear and negative-triangularity plasmas. Predictive STEP modeling has been used to assess performance in several tokamak reactors. Simulations of a high-field, large-aspect-ratio reactor show significantly lower fusion power than predicted by a zero-dimensional study, demonstrating the limitations of scaling-law extrapolations. STEP predictions have found promising scenarios for an EXhaust and Confinement Integration Tokamak Experiment, including a high-pressure, 80%-bootstrap-fraction plasma. ITER modeling with STEP has shown that pellet fueling enhances fusion gain in both the baseline and advanced-inductive scenarios. Finally, STEP predictions for the SPARC baseline scenario are in good agreement with published results from the physics basis.

A high-level design study for a new experimental tokamak shows that advances in fusion science and engineering can be leveraged to narrow the gaps in energy confinement and exhaust power handling that remain between present devices and a future fusion pilot plant (FPP). This potential new U.S. facility, an Exhaust and Confinement Integration Tokamak Experiment (EXCITE), will access an operational space close to the projected FPP performance regime via a compact, high-field, high-power-density approach that utilizes advanced tokamak scenarios and high-temperature superconductor magnets. Full-device optimization via system code calculations, physics-based core-edge modeling, plasma control simulations, and finite element structural and thermal analysis has converged on a BT=6 T, IP=5 MA, R0=1.5 m, A=3, D-D tokamak with strong plasma shaping, long-legged divertors, and 50 MW of auxiliary power. Such a device will match several absolute FPP parameters: plasma pressure, exhaust heat flux, and toroidal magnetic field. It will also narrow or close the gap in key dimensionless parameters: toroidal beta, bootstrap fraction, collisionality, and edge neutral opacity. Integrated neutron shielding preserves personnel access by limiting nuclear activation and maximizes experimental run time by reducing site radiation. In addition to design study results and optimization details, parameter sensitivities and uncertainties are also discussed.

We have developed an innovative workflow, Stability, Transport, Equilibrium, and Pedestal (STEP)-zero-dimensional (0D), within the OMFIT integrated modeling framework. Through systematic validation against the International Tokamak Physics Activity global H-mode confinement database, we demonstrated that STEP-0D, on average, predicts the energy confinement time with a mean relative error of less than 19%. Moreover, this workflow showed promising potential in predicting plasmas for proposed fusion reactors such as the affordable, robust, compact (ARC) reactor, the European demonstration power plant (EU-DEMO), and the China fusion engineering test reactor (CFETR) indicating moderate H-factors between 0.9 and 1.2. STEP-0D allows theory-based prediction of tokamak scenarios, beginning with 0D quantities. The workflow initiates with the PRO-create module, generating physically consistent plasma profiles and equilibrium using the same 0D quantities as the IPB98(y,2) confinement scaling. This sets the starting point for the STEP module, which further iterates between theory-based physics models of equilibrium, core transport, and pedestal to yield a self-consistent solution. Given these attributes, STEP-0D not only improves the accuracy of predicting plasma performance but also provides a path toward a novel fusion power plant design workflow. When integrated with engineering and costing models within an optimization, this new approach could eliminate the iterative reconciliation between plasma models of varying fidelity. This potential for a more efficient design process underpins STEP-0D's significant contribution to future fusion power plant development.

The OMFIT STEP (Meneghini et al. , Nucl. Fusion , vol. 10, 2020, p. 1088) workflow has been used to develop inductive and steady-state H-mode core plasma scenario use cases for a $B_0 = 8 \, {\rm T}$ , $R_0 = 4 \, {\rm m}$ machine to help guide and inform future higher-fidelity studies of core transport and confinement in compact tokamak reactors. Both use cases are designed to produce 200 MW or more of net electric power in an up-down symmetric plasma with minor radius $a = 1.4 \, {\rm m}$ , elongation $\kappa = 2.0$ , triangularity $\delta = 0.5$ and effective charge $Z_{{\rm eff}} \simeq 2$ . Additional considerations based on the need for compatibility of the core with reactor-relevant power exhaust solutions and external actuators were used to guide and constrain the use case development. An extensive characterization of core transport in both scenarios is presented, the most important feature of which is the extreme sensitivity of the results to the quantitative stiffness level of the transport model used as well as the predicted critical gradients. This sensitivity is shown to arise from different levels of transport stiffness exhibited by the models, combined with the gyroBohm-normalized fluxes of the predictions being an order of magnitude larger than other H-mode plasmas. Additionally, it is shown that although heating in both plasmas is predominantly to the electrons and collisionality is low, the plasmas remain sufficiently well coupled for the ions to carry a significant fraction of the thermal transport. As neoclassical transport is negligible in these conditions, this situation inherently requires long-wavelength ion gyroradius-scale turbulence to be the dominant transport mechanism in both plasmas. These results are combined with other basic considerations to propose a simple heuristic model of transport in reactor-relevant plasmas, along with simple metrics to quantify coupling and core transport properties across burning and non-burning plasmas.

This report is in partial fulfillment of deliverable D1.3 Code Validation (DIII-D). These simulations focus on thermal quench phase of the SPI mitigation and are not typically carried beyond it to the current spike and subsequent current quench. NIMROD SPI simulations[1] are validated against DIII-D experiments. The target plasma for these simulations is DIII-D 160606@02990ms.

Nonlinear 3D MHD simulations of shattered-pellet injection (SPI) in JET show prototypical SPI-driven disruptions using the M3D-C1 and NIMROD extended-MHD codes. Initially, radiation-driven thermal quenches are accelerated by MHD activity as the pellet crosses rational surfaces, leading to a radiation spike, global stochasticization of the magnetic field, and a complete thermal quench. Eventually, current quenches, preceded by a current spike are seen as the Ohmic heating becomes equal to the radiative cooling. The results are qualitatively similar for both a single monolithic pellet, pencil-beam model, and a realistic shatter to represent the SPI plume. A scan in viscosity from 500 to 2000 m 2 s −1 for MHD simulations finds that reducing viscosity increases MHD activity and decreases thermal quench time slightly. A realistic cloud of fragments modeling shows that mixed-D–Ne pellet travels deeper into the plasma core before the thermal quench. At the slow pellet speeds, the pellet is found to be moving slowly enough inward that even the 5% neon in the mixed pellet is enough to effectively radiate the thermal energy available. Radiation toroidal peaking is predicted to be at levels consistent with experimental observations and reduced as the pellet travels deeper into the plasma. These simulations lay the ground work for more-sophisticated validative and predictive modeling of SPI in JET using both M3D-C1 and NIMROD.

The effect of n = 1 magnetic perturbations (MPs) on prompt fast ion losses in DIII-D has been investigated using the light ion beam probe technique. The effect of normalized beta, β n , and the plasma response to the MPs is studied for several MP spectra. Magnetics data show a strong dependence of plasma response to β n that depends on the phase difference in perturbation coils, Δ ϕ U L . For most phases, the response increases with β n , however, the response is suppressed for phases between 180 ∘ and 240 ∘ . Experimental data from scintillator based fast ion loss detectors shows that relative fluctuation of lost ions (20%–30% of the steady signal) does not diminish across the L- to H-mode transition for Δ ϕ U L = 240 ∘ , despite the 34% decrease in radial response field and 50% decrease in poloidal response field. Simulations of the DIII-D discharges using M3D-C1 and ASCOT5 find that prompt losses from neutral beam injection in each investigated case hit the first wall at several concentrated locations: the vessel floor, midplane diagnostic ports, vessel ceiling, and inner wall. Simulated losses from co-injection neutral beams are born outside the last closed flux surface, corresponding to radial orbit displacements of 3–6 cm due to the MPs.

Disruptions are a serious problem in tokamaks, in which thermal and magnetic energy confinement is lost. This paper uses data from the DIII-D experiment, theory, and simulations to demonstrate that resistive wall tearing modes (RWTM) produce the thermal quench (TQ) in a typical locked mode shot. Analysis of the linear RWTM dispersion relation shows the parameter dependence of the growth rate, particularly on the resistive wall time. Linear simulations of the locked mode equilibrium show that it is unstable with a resistive wall, and stable with an ideally conducting wall. Nonlinear simulations demonstrate that the RWTM grows to sufficient amplitude to cause a complete thermal quench. The RWTM growth time is proportional to the thermal quench time. The nonlinearly saturated RWTM magnetic perturbation amplitude agrees with experimental measurements. The onset condition is that the q = 2 rational surface is sufficiently close to the resistive wall. Collectively, this identifies the RWTM as the cause of the TQ. In ITER, RWTMs will produce long TQ times compared to present-day experiments. ITER disruptions may be significantly more benign than previously predicted.