Successful demonstration of an implosion that meets the physics metrics for ignition on the National Ignition Facility (NIF) in August 2021 and demonstration of target energy gain G > 1 in December 2022 represented the culmination of more than a decade of research on the NIF. An in-depth analysis of the key ignition metrics achieved on the NIF over the past decade shows sustained progress toward identifying and mitigating degradation effects. Ignition implosions on the NIF have progressed from early experiments whose compressed fuel conditions were degraded by a factor of 10–20 below the ignition threshold with yields of only 1%–2% of the laser energy, to current experiments that significantly exceed the ignition threshold and in the best experiments achieve yields greater than twice the laser energy. It is very likely that NIF can get more than 20 MJ of yield and possibly 50–70 MJ yields when fully optimized at an ultraviolet laser energy of 2.6 MJ following the completion of the NIF Extended Yield Capability Project. Achieving these higher yields will also require improvements to capsules at larger size and possibly with alternate materials, as well as an improved understanding of hohlraum and capsule physics. Now that NIF has achieved ignition, the design of a Next Generation High Energy Density Facility that could achieve the National Nuclear Security Administration long-term goal of substantially higher yields than the NIF can proceed with a more confident physics base. We evaluate these opportunities including possible applications for inertial fusion energy and likely challenges to achieving this level of performance over the next decade.

For many decades, the running joke in fusion research has been that 'fusion' is thirty years away and always will be. Yet, these past few years we find ourselves in a position where we can now talk about the milestones of burning plasmas, fusion ignition, and target energy gain greater than unity (scientific breakeven) in the past tense. Fusion is no longer a joke! Yet getting to fusion ignition, the tipping-point of thermonuclear instability resulting in an explosive increase in ion thermal temperature and fusion reaction-rate, and scientific breakeven (target gain, G(target)= fusion yield/deposited laser energy >1, in the laser-driven inertial confinement fusion context) has not been easy. In this publication we discuss our present understanding of the physics and technological challenges surrounding ignition and Gain as well as highlight some outstanding problems that still need resolution.

Ignition and gain greater than unity has been achieved in inertial confinement fusion (ICF) implosions at the National Ignition Facility (NIF). These accomplishments required implosions that produced high hotspot pressures that are inertially confined by a dense shell of DT fuel. However, even in the burning and igniting plasma regime, 3D asymmetries can reduce the coupling of shell kinetic energy to the hotspot harming the overall implosion performance and truncating burn. Likewise, the overall scale of the implosion can be minimized by maintaining a high efficiency of energy coupling from the imploding shell to the hotspot. Recent experiments commonly show signs of significant 3D asymmetry that manifest as high hotspot velocity or asymmetry in the self-emission and scattered neutron images. While modeling 3D asymmetries in implosion with full scale hydrodynamic simulations is often performed, it is labor intensive and computationally costly. Therefore, 3D simulation is applied only in special cases like experiments of particular interest. To enable a wider survey of 3D post-shot analysis, an approximate but computationally inexpensive approach is applied by using multiple rocket-pistons discretizing the spherical implosion. These rocket-pistons are coupled together through the central hotspot pressure using the power balance equations. The approach is similar to that reported by Springer [Springer et al., Nuclear Fusion 59 (3) (2019)] with the inclusion of an approximate hohlraum model beginning at the rocket-implosion stage and post-processing of realistic synthetic diagnostic data at the stagnation and peak burn. This rocket piston tool can provide approximate 3D image and diagnostic data that can then be compared quantitively with data enabling new techniques in iterative, forward fitting, and machine learning to interpreting measurements.

Indirect Drive Inertial Confinement Fusion Experiments on the National Ignition Facility (NIF) have achieved a burning plasma state with neutron yields exceeding 170 kJ, roughly 3 times the prior record and a necessary stage for igniting plasmas. The results are achieved despite multiple sources of degradations that lead to high variability in performance. Results shown here, for the first time, include an empirical correction factor for mode-2 asymmetry in the burning plasma regime in addition to previously determined corrections for radiative mix and mode-1. Analysis shows that including these three corrections alone accounts for the measured fusion performance variability in the two highest performing experimental campaigns on the NIF to within error. Here we quantify the performance sensitivity to mode-2 symmetry in the burning plasma regime and apply the results, in the form of an empirical correction to a 1D performance model. Furthermore, we find the sensitivity to mode-2 determined through a series of integrated 2D radiation hydrodynamic simulations to be consistent with the experimentally determined sensitivity only when including alpha-heating. Recent improvements in the indirect-drive inertial confinement fusion experiments include the achievement of burning plasma state. Here the authors report the scaling of neutron yield in a burning plasma of Deuterium-Tritium fusion reaction by including the mode-2 asymmetry.

On December 5th, 2022, controlled fusion ignition was demonstrated for the first time at the National Ignition Facility (NIF), a major achievement in the field of Inertial Confinement Fusion (ICF) requiring a multi-decadal effort involving broad national and international collaborations. To drive the fusion ignition reaction with the compressed fuel capsule, that yielded 3.15 MJ of nuclear energy [1], the NIF laser delivered a high-precision pulse shape with 2.05 MJ of ultra-violet (UV) laser energy and a peak power of 440 TW. This laser energy was an increase of similar to 8 % compared to that delivered on the previous "threshold of ignition" record yield experiment (1.37 MJ of yield for 1.89 MJ of laser energy) on August 8th, 2021 [2]. We explain how the results of our extensive research in laser technology and UV optics damage mitigation led to major improvements in the NIF laser, enabling this energy increase along with additional accuracy, precision, and power balance enhancements. Furthermore, we will discuss on-going efforts that have enabled operations at 2.2 MJ of UV energy as well as potential new initiatives to push the laser performance -accuracy and delivered energy- to even higher levels in the future as previously demonstrated on a small subset of NIF beams [3].

We describe our current understanding of the variability and degradation mechanisms observed through a series of five indirectly driven inertial fusion implosions fielded at the National Ignition Facility in the fall of 2021, four of which attempted to reproduce the first experiment to achieve Lawson's criterion for ignition with a thermonuclear yield of 1.35 MJ on August 8, 2021. A large number of absolutely calibrated (imaging, time-resolved, and spectrally resolved) x-ray and neutron diagnostics are fielded on the NIF along multiple lines of sight for each experiment. This allows for a reconstruction of the DT fuel and ablator mix injected into the hotspot around peak burn. We show that nuclear yield variations are well reproduced by numerical modeling when the measured low mode asymmetries and mix mass are included. Furthermore, these observed perturbations during burn are linked to small variations in laser delivery and capsule defects. Stringent specifications are then set to achieve robust ignition with the implosion design studied in this paper. (C) 2024 Author(s).

An indirect -drive inertial fusion experiment on the National Ignition Facility was driven using 2.05 MJ of laser light at a wavelength of 351 nm and produced 3.1 +/- 0.16 MJ of total fusion yield, producing a target gain G = 1.5 +/- 0.1 exceeding unity for the first time in a laboratory experiment [Phys. Rev. E 109, 025204 (2024)]. Herein we describe the experimental evidence for the increased drive on the capsule using additional laser energy and control over known degradation mechanisms, which are critical to achieving high performance. Improved fuel compression relative to previous megajoule-yield experiments is observed. Novel signatures of the ignition and burn propagation to high yield can now be studied in the laboratory for the first time.

On December 5, 2022, an indirect drive fusion implosion on the National Ignition Facility (NIF) achieved a target gain G_{target} of 1.5. This is the first laboratory demonstration of exceeding "scientific breakeven" (or G_{target}>1) where 2.05 MJ of 351 nm laser light produced 3.1 MJ of total fusion yield, a result which significantly exceeds the Lawson criterion for fusion ignition as reported in a previous NIF implosion [H. Abu-Shawareb et al. (Indirect Drive ICF Collaboration), Phys. Rev. Lett. 129, 075001 (2022)PRLTAO0031-900710.1103/PhysRevLett.129.075001]. This achievement is the culmination of more than five decades of research and gives proof that laboratory fusion, based on fundamental physics principles, is possible. This Letter reports on the target, laser, design, and experimental advancements that led to this result.

In this work we present the design of the first controlled fusion laboratory experiment to reach target gain G>1 N221204 (5 December 2022) [Phys. Rev. Lett. 132, 065102 (2024)10.1103/PhysRevLett.132.065102], performed at the National Ignition Facility, where the fusion energy produced (3.15 MJ) exceeded the amount of laser energy required to drive the target (2.05 MJ). Following the demonstration of ignition according to the Lawson criterion N210808, experiments were impacted by nonideal experimental fielding conditions, such as increased (known) target defects that seeded hydrodynamic instabilities or unintentional low-mode asymmetries from nonuniformities in the target or laser delivery, which led to reduced fusion yields less than 1 MJ. This Letter details design changes, including using an extended higher-energy laser pulse to drive a thicker high-density carbon (also known as diamond) capsule, that led to increased fusion energy output compared to N210808 as well as improved robustness for achieving high fusion energies (greater than 1 MJ) in the presence of significant low-mode asymmetries. For this design, the burnup fraction of the deuterium and tritium (DT) fuel was increased (approximately 4% fuel burnup and a target gain of approximately 1.5 compared to approximately 2% fuel burnup and target gain approximately 0.7 for N210808) as a result of increased total (DT plus capsule) areal density at maximum compression compared to N210808. Radiation-hydrodynamic simulations of this design predicted achieving target gain greater than 1 and also the magnitude of increase in fusion energy produced compared to N210808. The plasma conditions and hotspot power balance (fusion power produced vs input power and power losses) using these simulations are presented. Since the drafting of this manuscript, the results of this paper have been replicated and exceeded (N230729) in this design, together with a higher-quality diamond capsule, setting a new record of approximately 3.88MJ of fusion energy and fusion energy target gain of approximately 1.9.

Laser-driven Hohlraums filled with gas at lower densities (<0.6 mg/cc) have higher efficiency compared to original ≥ 0.96 mg/cc fill because of reduced backscatter losses [Hall et al., Phys. Plasmas 24, 052706 (2017)]. However, using low-density filled Hohlraums with longer drive required for lower adiabat implosions, and hence potentially higher inertial confinement fusion gain designs, has been challenging since the Hohlraum wall blow-off is less tamped, thus altering the laser beam absorption regions and drive symmetry. A series of NIF experiments using optimized pulse shaping, beam pointing, and temporal phasing have demonstrated, through imaging of the Hohlraum and capsule dynamics, that a symmetric implosion using a 14-ns low-adiabat drive pulse {2× longer than high-density-carbon ablator designs using low gas-fill density Hohlraums [Divol et al., Phys. Plasmas 24, 056309 (2017)]} is possible in a low backscatter loss 0.45 mg/cc He-filled Hohlraum. The ingress of the Hohlraum walls was mitigated by revisiting the adiabat-shaped design [Clark et al., Phys. Plasmas 21, 112705 (2014)] that uses a low-power (1 TW) trough that delays the wall expansion. Low-mode P2 and P4 drive asymmetry swings caused by the drift of the laser spots were essentially zeroed out by employing temporal beam phasing between cones of beams [Turner et al., Phys. Plasmas 7, 333 (2000)]. The results also indicate an improved coupling efficiency of ∼30% compared to an earlier design using higher density filled Hohlraums and pave the way for revisiting low-adiabat, high convergence drives using CH ablators.

Inertial confinement fusion ignition requires high inflight shell velocity, good energy coupling between the hotspot and shell, and high areal density at peak compression. Three-dimensional asymmetries caused by imperfections in the drive symmetry or target can grow and damage the coupling and confinement. Recent high-yield experiments have shown that low-mode asymmetries are a key degradation mechanism and contribute to variability. We show the experimental signatures and impacts of asymmetry change with increasing implosion yield given the same initial cause. This letter has implications for improving robustness to a key degradation in ignition experiments.

The change in the power balance, temporal dynamics, emission weighted size, temperature, mass, and areal density of inertially confined fusion plasmas have been quantified for experiments that reach target gains up to 0.72. It is observed that as the target gain rises, increased rates of self-heating initially overcome expansion power losses. This leads to reacting plasmas that reach peak fusion production at later times with increased size, temperature, mass and with lower emission weighted areal densities. Analytic models are consistent with the observations and inferences for how these quantities evolve as the rate of fusion self-heating, fusion yield, and target gain increase. At peak fusion production, it is found that as temperatures and target gains rise, the expansion power loss increases to a near constant ratio of the fusion self-heating power. This is consistent with models that indicate that the expansion losses dominate the dynamics in this regime.

An inertial fusion implosion on the National Ignition Facility, conducted on August 8, 2021 (N210808), recently produced more than a megajoule of fusion yield and passed Lawson's criterion for ignition [Phys. Rev. Lett. 129, 075001 (2022)10.1103/PhysRevLett.129.075001]. We describe the experimental improvements that enabled N210808 and present the first experimental measurements from an igniting plasma in the laboratory. Ignition metrics like the product of hot-spot energy and pressure squared, in the absence of self-heating, increased by ∼35%, leading to record values and an enhancement from previous experiments in the hot-spot energy (∼3×), pressure (∼2×), and mass (∼2×). These results are consistent with self-heating dominating other power balance terms. The burn rate increases by an order of magnitude after peak compression, and the hot-spot conditions show clear evidence for burn propagation into the dense fuel surrounding the hot spot. These novel dynamics and thermodynamic properties have never been observed on prior inertial fusion experiments.

A new additional wavelength-tuning capability has been implemented on the National Ignition Facility (NIF) laser allowing for unprecedented control of crossed-beam energy transfer (CBET) between all groups of beams for better performance of indirect-drive inertial confinement fusion (ICF) ignition experiments. In particular, this advance allows for negation and reversal of flow-induced CBET and the rebalancing of the intensity of different groups of beams within an indirect-drive (ICF) hohlraum. Experiments conducted at the NIF using a 1.1 MJ laser pulse with peak power of 390 TW demonstrate this high level of control through measurements of the precise changes to stimulated Brillouin scattering, typically driven by flow-induced CBET at the end of the pulse. Additionally, this new capability is shown to be able to predictably control gold-wall plasma expansion in the target driven by early-time flow-induced CBET. Estimates of early-time CBET from the wall expansion are shown to be consistent with simulation expectations. This new additional capability to control symmetry and backscatter expands the design space of current experiments and provides extra margin for increased laser energy in near-future experiments.

Previously, hydrodynamic simulations [Clark et al., Phys. Plasmas 23, 072707 (2016)] suggested that precisely tailoring the capsule ablator thickness (shimming) could counterbalance cylindrical Hohlraum Legendre P4 drive asymmetries at the capsule in laser indirect drive implosions. As a result, the stagnated deuterium–tritium (DT) fuel areal density P4 asymmetry is reduced, potentially resulting in a nuclear yield increase. Inflight radiographs of various level of shimmed capsules with plastic (CH) ablators showed that shims can indeed control the in-flight capsule shell P4 asymmetry, with a linear sensitivity to shim amplitude that is close to analytic estimates and simulations. Furthermore, the stagnated DT fuel areal density P4 asymmetry inferred from downscattered neutron imaging was reduced when the capsule shim was applied, in agreement with simulations matching the inflight shell asymmetry. A nuclear yield improvement via shim was not observed, as predicted, likely due to implosion instabilities and as built capsule shim deviations from an ideal P4 shape.

For more than half a century, researchers around the world have been engaged in attempts to achieve fusion ignition as a proof of principle of various fusion concepts. As recently reported, a burning plasma state, where the alpha-heating in the plasma is the primary source of heating, was achieved in laboratory experiments. Following the Lawson criterion, an ignited plasma is one where the fusion heating power is high enough to overcome all the physical processes that cool the fusion plasma, creating a positive thermodynamic feedback loop with rapidly increasing temperature. In inertially confined fusion, ignition is a state where the fusion plasma can begin ``burn propagation'' into surrounding cold fuel, enabling the possibility of high energy gain. While ``scientific breakeven'' (i.e. unity target gain) has not yet been achieved, this talk reports the first controlled fusion experiment on the National Ignition Facility to produce capsule gain greater than unity (here 5.8) and reach ignition by many different formulations of the Lawson criterion. In the talk, we will discuss some key basic physics inertial confinement fusion (ICF) principles behind the burning plasma and ignition results as well as discuss future challenges.

Obtaining a burning plasma is a critical step towards self-sustaining fusion energy 1 . A burning plasma is one in which the fusion reactions themselves are the primary source of heating in the plasma, which is necessary to sustain and propagate the burn, enabling high energy gain. After decades of fusion research, here we achieve a burning-plasma state in the laboratory. These experiments were conducted at the US National Ignition Facility, a laser facility delivering up to 1.9 megajoules of energy in pulses with peak powers up to 500 terawatts. We use the lasers to generate X-rays in a radiation cavity to indirectly drive a fuel-containing capsule via the X-ray ablation pressure, which results in the implosion process compressing and heating the fuel via mechanical work. The burning-plasma state was created using a strategy to increase the spatial scale of the capsule 2 , 3 through two different implosion concepts 4 – 7 . These experiments show fusion self-heating in excess of the mechanical work injected into the implosions, satisfying several burning-plasma metrics 3 , 8 . Additionally, we describe a subset of experiments that appear to have crossed the static self-heating boundary, where fusion heating surpasses the energy losses from radiation and conduction. These results provide an opportunity to study α-particle-dominated plasmas and burning-plasma physics in the laboratory.

We present the design of the first igniting fusion plasma in the laboratory by Lawson's criterion that produced 1.37 MJ of fusion energy, Hybrid-E experiment N210808 (August 8, 2021) [Phys. Rev. Lett. 129, 075001 (2022)10.1103/PhysRevLett.129.075001]. This design uses the indirect drive inertial confinement fusion approach to heat and compress a central "hot spot" of deuterium-tritium (DT) fuel using a surrounding dense DT fuel piston. Ignition occurs when the heating from absorption of α particles created in the fusion process overcomes the loss mechanisms in the system for a duration of time. This letter describes key design changes which enabled a ∼3-6× increase in an ignition figure of merit (generalized Lawson criterion) [Phys. Plasmas 28, 022704 (2021)1070-664X10.1063/5.0035583, Phys. Plasmas 25, 122704 (2018)1070-664X10.1063/1.5049595]) and an eightfold increase in fusion energy output compared to predecessor experiments. We present simulations of the hot-spot conditions for experiment N210808 that show fundamentally different behavior compared to predecessor experiments and simulated metrics that are consistent with N210808 reaching for the first time in the laboratory "ignition."