We have demonstrated the world's highest average power, fully diode-pumped, petawatt-class peak power laser, the High-repetition-rate Advanced Petawatt Laser System (HAPLS) [1-3]. These first commissioning results at 16J (stretched) at 3%Hz fully validate projected performance of 30J/30fs (>1PW) at 10Hz. The laser has been operated at this intermediate level at Lawrence Livermore National Laboratory to demonstrate integrated performance of all subsystems and provide benchmarking data to laser performance models before further increasing energy and peak power. Data was obtained during multiple campaigns, exceeding several hours of run time, and a snapshot of 60min of data is shown in Fig. 1. The average pump laser 1ω (1053nm) energy was 97J with an rms stability of 0.7%, 2ω (527nm) energy at the Ti:sapphire power amplifier was 62J, and the average stretched short pulse energy was 16J. A full-aperture diagnostic suite allows simultaneous, single-shot measurement of energy, spectrum, beam quality, and pulse duration at full repetition rate. Single-shot SPIDER retrieved pulse shapes (Fig. 1 inset) with an average pulse duration over 12000 consecutive shots of 28.6fs (rms=1.4fs). The mean pulse duration is consistent with the measured spectral bandwidth and is ∼1.2× the transform limit. All results shown are raw data without filtering or averaging, demonstrating the exceptional pulse characteristics, repeatability, and stability of the entire laser system.

Overview of progress in construction and testing of the laser systems of ELI-Beamlines, accomplished since 2015, is presented. Good progress has been achieved in construction of all four lasers based largely on the technology of diode-pumped solid state lasers (DPSSL). The first part of the L1 laser, designed to provide 200 mJ < 15 fs pulses at 1 kHz repetition rate, is up and running. The L2 is a development line employing a 10 J / 10 Hz cryogenic gas-cooled pump laser which has recently been equipped with an advanced cryogenic engine. Operation of the L3-HAPLS system, using a gas-cooled DPSSL pump laser and a Ti: sapphire broadband amplifier, was recently demonstrated at 16 J / 28 fs, at 3.33 Hz rep rate. Finally, the 5 Hz OPCPA front end of the L4 kJ laser is up running and amplification in the Nd:glass large-aperture power amplifiers was demonstrated.

Large laser systems that deliver optical pulses with peak powers exceeding one Petawatt (PW) have been constructed at dozens of research facilities worldwide and have fostered research in High-Energy-Density (HED) Science, High-Field and nonlinear physics [1]. Furthermore, the high intensities exceeding 1018W/cm2 allow for efficiently driving secondary sources that inherit some of the properties of the laser pulse, e.g. pulse duration, spatial and/or divergence characteristics. In the intervening decades since that first PW laser, single-shot proof-of-principle experiments have been successful in demonstrating new high-intensity laser-matter interactions and subsequent secondary particle and photon sources. These secondary sources include generation and acceleration of charged-particle (electron, proton, ion) and neutron beams, and x-ray and gamma-ray sources, generation of radioisotopes for positron emission tomography (PET), targeted cancer therapy, medical imaging, and the transmutation of radioactive waste [2, 3]. Each of these promising applications requires lasers with peak power of hundreds of terawatt (TW) to petawatt (PW) and with average power of tens to hundreds of kW to achieve the required secondary source flux.

The HAPLS laser system has been commissioned to its first integrated performance milestone, delivering laser pulses with 16J sub-30fs duration at a 3⅓Hz repetition rate. This first all-diode-pumped petawatt-class laser offers the average powers required for secondary source applications.

We present two high bandwidth data transmission and recording systems for the measurement of transient signals during pulsed power and laser produced plasmas. These systems use fiber optic cables to transmit analog data over long distances to high bandwidth digitizing oscilloscopes. One system is based on the direct modulation of a laser diode and has a bandwidth of 1.5GHz. The other system is based upon a Mach-Zehnder modulator and has a bandwidth of 12GHz, and is limited by the photoreceiver. The signals are recorded on commercial digitizing oscilloscopes that have approximately six effective bits. The transmission systems use many off-the-shelf components from the telecommunications industry and thus have a high reliability and a moderate cost. Investigation of the reduction in optical transmission of the fibers during exposure to high dose radiation will also be discussed.

X-ray topography was used to characterize crystals of potassium dihydrogen phosphate and volumes in these crystals that had been damaged by 1 ns, 1064 nm laser pulses. The crystals exhibited a nonuniform distribution of defects: linear dislocation networks, cracks, transition or growth layers, sectors and inclusions at which dislocation networks were initiated. The damaged volumes contained individual domains each composed of a central core of highly disturbed material surrounded by a spherically symmetric radial strain field. There was not an unambiguous correlation between the pre-existing X-ray topography microstructure of a test volume and its laser-damage threshold. In some crystals, thresholds were least in test volumes with a high density of line defect networks. In other crystals, volumes free of defects had the least thresholds. Therefore, some entity not resolvable by X-ray topography, possibly a point defect impurity cluster, was the limiting cause of damage.