Over 97% of all integrated circuits produced today are available only in plastic encapsulated, surface mountable, commercial grade or industrial grade versions. This is especially true for the most advanced technologies, such as high-speed microprocessors. The cost, availability, and functionality advantages of these devices are causing many electronics manufacturers to consider using them in elevated temperature applications such as avionics and automotive electronic systems to ensure early affordable access to leading edge technology. However, manufacturers only guarantee the operation of commercial devices in the 0 to 70/spl deg/C temperature range, and the industrial devices in the -40 to 85/spl deg/C temperature range. This paper describes the first study which addresses the reliability of plastic encapsulated microcircuits (PEMs) in the range from 125 to 300/spl deg/C, well outside the manufacturer's suggested temperature limits. In this study, Motorola MC68332 microcontroller, which is widely used in avionic systems, remained fully functional to 180/spl deg/C. However, this study also revealed that industrial grade, plastic encapsulated MC68332 devices had less than half the lifespan at 180/spl deg/C of similar MC68332 devices packaged in hermetic ceramic packages. In addition to the MC68332, the other nine types of plastic components studied had a shorter lifespan at 180/spl deg/C than their ceramic packaged counterparts. Outgassing of flame retardants with the associated catalysis of the growth of intermetallics was determined to be the principal cause of failure in the plastic components. Further studies conducted on 84-lead PQFP leadframes encapsulated in two different molding compounds revealed that the plastic encapsulant itself begins to lose its ability to insulate leads at temperatures greater than 250/spl deg/C and can actually combust at temperatures greater than 300/spl deg/C. Both insulation resistance degradation and cracking were found to be more prevalent in novalac than biphenyl.

Over 97% of all integrated circuits produced today are available only in plastic encapsulated, surface mountable, commercial grade or industrial grade versions. This is especially true for the most advanced technologies, such as high-speed microprocessors. The cost, availability, and functionality advantages of these devices are causing many electronics manufacturers to consider using them in elevated temperature applications such as avionics and automotive under-hood electronic systems to ensure early affordable access to leading edge technology. However, manufacturers only guarantee the operation of commercial devices in the 0 degrees C to 70 degrees C temperature range, and industrial devices in the -40 degrees C to 85 degrees C temperature range.This paper describes the first study which addresses the reliability of plastic encapsulated microcircuits (PEMs) in the range from 125 degrees C to 300 degrees C, well outside the manufacturer's suggested temperature limits. Previous work has indicated that PEMs sold for use in the commercial and industrial temperature ranges can often operate within the manufacturer's suggested electrical parameter specifications at much higher temperatures. For example, in this study the Motorola MC68332 microcontroller, which is widely used in avionic systems, remained fully functional to 180 degrees C. This is in accordance with previous work that indicated no fundamental constraints to the operation of silicon devices at temperatures up to 200 degrees C. However, this study also revealed that industrial grade, plastic encapsulated MC68332 devices had less than half the lifespan at 180 degrees C than similar MC68332 devices packaged in hermetic ceramic packages. In addition to the MC68332, the other nine types of plastic components studied had a shorter lifespan at 180 degrees C than their ceramic packaged counterparts. Outgassing of flame-retardants with the associated catalysis of the growth of intermetallics was determined to be the principal cause of failure in the plastic components.Further studies conducted on 84-lead plastic quad flatpack (PQFP) leadframes encapsulated in two different molding compounds revealed that the plastic encapsulant itself begins to lose its ability to insulate leads at temperatures greater than 250 degrees C and can actually combust at temperatures greater than 300 degrees C. Both insulation resistance degradation and cracking were found to be more prevalent in novalac than biphenyl. In summary, these studies have shown that while plastic encapsulated microelectronics can operate at temperatures above 125 degrees C, they have less than half the life of ceramic microcircuits sit 180 degrees C and they begin to show signs of insulation resistance degradation after 300 hours at 250 degrees C. (C) Published by Elsevier Science Ltd.

Over 97% of all integrated circuits produced today are available only in plastic encapsulated, surface mountable, commercial grade or industrial grade versions. This is especially true for the most advanced technologies, such as high-speed microprocessors. The cost, availability, and functionality advantages of these devices are causing many electronics manufacturers to consider using them in elevated temperature applications such as avionics and automotive under-hood electronic systems to ensure early affordable access to leading edge technology. However, manufacturers only guarantee the operation of commercial devices in the 0°C to 70°C temperature range, and the industrial devices in the -40°C to 85°C temperature range. This paper describes the first study which addresses the reliability of plastic encapsulated microcircuits (PEMs) in the range from 125°C to 300°C, well outside the manufacturer's suggested temperature limits. Previous work has indicated that PEMs sold for use in the commercial and industrial temperature ranges can often operate within the manufacturer's suggested electrical parameter specifications at much higher temperatures. For example, in this study, a Motorola MC68332 microcontroller, which is widely used in avionic systems, remained fully functional to 180°C. This is in accordance with previous work that indicated no fundamental constraints to the operation of silicon devices at temperatures up to 200°C. However, this study also revealed that industrial grade, plastic encapsulated MC68332 devices had less than half the lifespan at 180°C of similar MC68332 devices packaged in hermetic ceramic packages. In addition to the MC68332, the other nine types of plastic components studied had a shorter lifespan at 180°C than their ceramic packaged counterparts. Outgassing of flame retardants with the associated catalysis of the growth of intermetallics was determined to be the principal cause of failure in the plastic components. Further studies conducted on 84-lead PQFP leadframes encapsulated in two different molding compounds revealed that the plastic encapsulant itself begins to lose its ability to insulate leads at temperatures greater than 250°C and can actually combust at temperatures greater than 300°C. Both insulation resistance degradation and cracking were found to be more prevalent in novalac than biphenyl. In summary, these studies have shown that while plastic encapsulated microelectronics can operate at temperatures above 125°C, they have less than half the life of ceramic microcircuits at 180°C and they begin to show signs of insulation resistance degradation after 300 hours at 250°C.