Imaging methods by the means of optical sensors are applied in diverse scientific areas such as medical research and diagnostics, aerodynamics, environmental analysis, or marine research. After a general introduction to the field, this review is focused on works published between 2012 and 2022. The covered topics include planar sensors (optrodes), nanoprobes, and sensitive coatings. Advanced sensor materials combined with imaging technologies enable the visualization of parameters which exhibit no intrinsic color or fluorescence, such as oxygen, pH, CO2, H2O2, Ca2+, or temperature. The progress on the development of multiple sensors and methods for referenced signal read out is also highlighted, as is the recent progress in device design and application formats using model systems in the lab or methods for measurements' in the field.

Lanthanide-doped NaYF4 upconversion nanoand microcrystals were synthesized via a facile solvothermal approach. Thereby, the influence of volume ratios of ethylene glycol (EG)/H2O, molar ratios of NH4F/RE 3+ (RE represents the total amount of Y and rare-earth dopant ions), Gd ion contents, types of activator dopant ions, and different organic co-solvents on the crystal phase, size, and morphology of the resulting particles were studied systematically. A possible formation mechanism for the growth of crystals of different morphology is discussed. Our results show that the transition from the αto the β-phase mainly depends on the volume ratio of EG/H2O and the molar ratio of NH4F/RE , while the morphology and size could be controlled by the type of organic co-solvent and Gd dopant ions. Furthermore, the reaction time has to be long enough to convert αNaYF4 into β-NaYF4 during the growth process to optimize the upconversion luminescence. The formation of larger βNaYF4 crystals, which possess a higher upconversion luminescence than smaller particles, proceeds via intermediates of smaller crystals of cubic structure. In summary, our synthetic approach presents a facile route to tailor the size, crystal phase, morphology, and luminescence features of upconversion materials.

In this communication a novel concept for pH sensing is introduced which is specifically adapted to monitor carbonation induced corrosion in concrete structures. The method is based on a ratiometric measurement principle, exploiting the pH sensitive colour switching of thymol blue in the basic pH regime and the emissive properties of two different (Zn)CdSe/ZnS core shell quantum dots. The transition point of thymol blue in a Hydrogel D4 matrix was determined to be at around pH 11.6, which fits ideally to the intended application. Next to the fundamental spectroscopic characterization of the ratiometric response, a new design for a sensor head, suitable for the incorporation into concrete matrices is presented. Toward this, a manufacturing process was developed which includes the preparation of a double layer of polymers containing either thymol blue or a quantum dot mixture inside a porous ceramic tube. Results of a proof-of-priciple performance test of the sensor head in solutions of different pH and in cement specimens are presented, with encouraging results paving the way for future field tests in concrete.

An emerging class of inorganic optical reporters are near-infrared (NIR) excitable lanthanide-based upconversion nanoparticles (UCNPs) with multicolor emission and long luminescence lifetimes in the range of several hundred microseconds. For the design of chemical sensors and optical probes that reveal analyte-specific changes in their spectroscopic properties, these nanomaterials must be combined with sensitive indicator dyes that change their absorption and/or fluorescence properties selectively upon interaction with their target analyte, utilizing either resonance energy transfer (RET) processes or reabsorption-related inner filter effects. The rational development of UCNP-based nanoprobes for chemical sensing and imaging in a biological environment requires reliable methods for the surface functionalization of UCNPs, the analysis and quantification of surface groups, a high colloidal stability of UCNPs in aqueous media as well as the chemically stable attachment of the indicator molecules, and suitable instrumentation for the spectroscopic characterization of the energy-transfer systems and the derived nanosensors. These topics are highlighted in the following feature article, and examples of functionalized core-shell nanoprobes for the sensing of different biologically relevant analytes in aqueous environments will be presented. Special emphasis is placed on the intracellular sensing of pH.

The design of anion-sensitive probes with sufficient sensitivity and selectivity is a demanding task inanalytical sciences and chemical sensor technology. The reversible binding of anions to lanthanide centers is a possible approach for the development of molecular anion sensors, as reversibility is a prerequisite for continuous sensing and monitoring of enzymatic reactions. Some anion species lead to a strong increase of luminescence intensities and lifetimes by the replacement of luminescence quenching water molecules, though the selectivity of the luminescence response is still a major problem. We synthesized a series of positively charged pyridyl-based multidentate europium complexes (five-, four- and three dentate) including sensitizing chromophores and studied their luminescence intensity and lifetime responses to different polyphosphates, pyrophosphate, phosphate anions, and carboxyanions. The results revealed that the number and symmetry of the binding sites have a significant impact on the response. The five-dentate complex was used for the real-time monitoring of the activity of the ATP hydrolyzing enzyme apyrase.

Fluorescence imaging microscopy is an essential tool in biomedical research. Meanwhile, various fluorescent probes are available for the staining of cells, cell membranes, and organelles. Though, to monitor intracellular processes and dysfunctions, probes that respond to ubiquitous chemical parameters determining the cellular function such as pH, pO2 , and Ca(2+) are required. This review is focused on the progress in the design, fabrication, and application of photoluminescent nanoprobes for sensing and imaging of pH in living cells. The advantages of using nanoprobes carrying fluorescent pH indicators compared to single molecule probes are discussed as well as their limitations due to the mostly lysosomal uptake by cells. Particular attention is paid to ratiometric dual wavelength nanosensors that enable intrinsic referenced measurements. Referencing and proper calibration procedures are basic prerequisites to carry out reliable quantitative pH determinations in complex samples such as living cells. A variety of examples will be presented that highlight the diverseness of nanocarrier materials (polymers, micelles, silica, quantum dots, carbon dots, gold, photon upconversion nanocrystals, or bacteriophages), fluorescent pH indicators for the weak acidic range, and referenced sensing mechanisms, that have been applied intracellularly up to now. WIREs Nanomed Nanobiotechnol 2016, 8:378-413. doi: 10.1002/wnan.1366 For further resources related to this article, please visit the WIREs website.

Measurement of changes of pH at various intracellular compartments has potential to solve questions concerning the processing of endocytosed material, regulation of the acidification process, and also acidification of vesicles destined for exocytosis. To monitor these events, the nanosized optical pH probes need to provide ratiometric signals in the optically transparent biological window, target to all relevant intracellular compartments, and to facilitate imaging at subcellular resolution without interference from the biological matrix. To meet these criteria we sensitize the surface conjugated pH sensitive indicator via an upconversion process utilizing an energy transfer from the nanoparticle to the indicator. Live cells were imaged with a scanning confocal microscope equipped with a low-energy 980 nm laser excitation, which facilitated high resolution and penetration depth into the specimen, and low phototoxicity needed for long-term imaging. Our upconversion nanoparticle resonance energy transfer based sensor with polyethylenimine-coating provides high colloidal stability, enhanced cellular uptake, and distribution across cellular compartments. This distribution was modulated with membrane integrity perturbing treatment that resulted into total loss of lysosomal compartments and a dramatic pH shift of endosomal compartments. These nanoprobes are well suited for detection of pH changes in in vitro models with high biological background fluorescence and in in vivo applications, e.g., for the bioimaging of small animal models.

The mechanism for red upconversion luminescence of Yb-Er codoped materials is not generally agreed on in the literature. Both two-photon and three-photon processes have been suggested as the main path for red upconversion emission. We have studied beta-NaYF4:Yb-3,Er3+ nanoparticles in H2O and D2O, and we propose that the nanoparticle environment is a major factor in the selection of the preferred red upconversion excitation pathway. In H2O, efficient multiphonon relaxation (MPR) promotes the two-photon mechanism through green emitting states, while, in D2O, MPR is less effective and the three-photon path involving back energy transfer to Yb3+ is the dominant mechanism. For the green upconversion emission, our results suggest the common two-photon path through the F-4(9/2) energy state in both H2O and D2O.

The luminescence intensity ratio (LIR) of the green emissions of the near-infrared excited NaYF4 :Yb3+ ,Er3+ nanocrystals is a promising method for temperature sensing. Here, the influence of excitation power density, excitation pulse length, excitation wavelength, silica shell, and solvent on the LIR and its temperature response is reported. The primary objective is to study the LIR mechanism and the impact of measurement and environmental parameters on the calibration and precision of the LIR. The LIR value is demonstrated to be unaffected by the excitation intensity in the studied range. This result is essential, considering the application feasibility of the LIR method as temperature sensor, where the effective excitation power density depends on the sample matrix and the distance excitation light travels in the sample. The pulsed excitation, however, results in an increase in the LIR value upon short pulse width. Silanization of bare nanocrystals has no effect on the LIR values, but the local warming of H2 O samples under laser exposure results in slightly increased LIR values compared to other solvents; D2 O, oleic acid, and dimethyl sulfoxide. The thermal quenching of luminescence lifetimes of Er3+ emission is proved to be too weak for sensing applications.

A strongly fluorescent organic semiconducting polymer doped with a highly temperature dependent fluorescent europium(III) complex is converted into a nanosized material that is capable of optically sensing temperature ( T ) in the range from 0 to 50 °C via two‐photon excitation at 720 nm. The nanosensors are prepared from a blue‐fluorescent polyfluorene that acts as both a light‐harvesting antenna (to capture two‐photon energy) and an energy donor in a fluorescence resonance energy transfer (FRET) system. The photonic energy absorbed by the polymer is transferred to the T ‐sensitive red‐luminescent europium complex contained in the nanoparticles. The close spatial proximity of the donor and the acceptor warrants efficient FRET. A poly(ethylene glycol)‐ co ‐poly(propylene oxide) block copolymer is also added to render the particles biocompatible. It is shown that T can be calculated from a) the intensity of the luminescence of the europium complex, b) the ratio of the intensities of the red and blue luminescence, or c) the T ‐dependent luminescence lifetime of the Eu(III) complex.

The demand for photostable luminescent reporters that absorb and emit light in the red to near-infrared (NIR) spectral region continues in biomedical research and bioanalysis. In recent years, classical organic fluorophores have increasingly been displaced by luminescent nanoparticles. These consist of either polymer or silica based beads that are loaded with luminescent dyes, conjugated polymers, or inorganic nanomaterials such as semiconductor nanocrystals (quantum dots), colloidal clusters of silver and gold, or carbon dots. Among the inorganic materials, photon upconversion nanocrystals exhibit a high potential for application to bioimaging or biomolecular assays. They offer an exceptionally high photostability, can be excited in the NIR, and their anti-Stokes emission enables luminescence detection free of background and perturbing scatter effects even in complex biological samples. These lanthanide doped inorganic crystals have multiple emission lines that can be tuned by the selection of the dopants.This review article is focused on the applications of functionalized photon upconversion nanoparticles (UCNPs) to chemical sensing. This is a comparatively new field of research activity and mainly directed at the sensing and imaging of ubiquitous chemical analytes in biological samples, particularly in living cells. For this purpose, the particles have to be functionalized with suitable indicator dyes or recognition elements, as they do not show an intrinsic or specific luminescence response to most of these analytes (e.g. pH, oxygen, metal ions). We describe the strategies for the design of such responsive nanocomposites utilizing either luminescence resonance energy transfer or emission-reabsorption (inner filter effect) mechanisms and also highlight examples for their use either immobilized in sensor layers or directly as nanoprobes for intracellular sensing and imaging.

The synthesis of novel Eu complexes with 1,3-di(thienyl)propane-1,3-diones as ligands as well as their luminescence properties in different polymers are reported. The new temperature sensitive paints (TSPs) exhibit not only exceptional high temperature sensitivity over a wide range of temperatures but are also characterized by negligible pressure sensitivity and marked photostability. This is why they are outstandingly suitable for applications, e.g. in aerodynamics and hydrodynamics. (C) 2015 Elsevier B.V. All rights reserved.

We have studied the mechanisms of water-based quenching of the upconversion photoluminescence of upconverting nanophosphors (UCNPs) via luminescence decay measurements for a better understanding of the non-radiative deactivation pathways responsible for the relatively low upconversion luminescence efficiency in aqueous solutions. This included both upconversion luminescence measurements and the direct excitation of emissive energy states of Er3+ and Yb3+ dopants in NaYF4:Yb3+, Er3+ UCNPs by measuring the decays at 550 and 655 nm upon 380 nm excitation and at 980 nm upon 930 nm excitation, respectively. The luminescence intensities and decays were measured from both bare and silanized NaYF4:Yb3+, Er3+ and NaYF4:Yb3+, Tm3+ UCNPs in H2O and D2O. The measurements revealed up to 99.9% quenching of the upconversion photoluminescence intensity of both Er3+ and Tm3+ doped bare nanophosphors by water. Instead of the multiphonon relaxation of excited energy levels of the activators, the main mechanism of quenching was found to be the multiphonon deactivation of the Yb3+ sensitizer ion caused by OH-vibrations on the surface of the nanophosphor. Due to the nonlinear nature of upconversion, the quenching of Yb3+ has a higher order effect on the upconversion emission intensity with the efficient Yb-Yb energy migration in the similar to 35 nm nanocrystals making the whole nanophosphor volume susceptible to surface quenching effects. The study underlines the need of efficient surface passivation for the use of UCNPs as labels in bioanalytical applications performed in aqueous solutions.

We report on the use of a sprayable and thermogelating biomaterial (Poloxamer (TM); a.k.a. Pluronic (TM)) in optical imaging of pH values, local oxygen and temperature. The material is highly biocompatible and easy to handle. We also show that the material is well permeable to oxygen (thus making it a good choice for use in oxygen sensors), and is stable in liquid solution and at elevated temperature. We demonstrate its applicability in optical sensors for oxygen, pH and temperature. This was accomplished by incorporating appropriate luminescent probes in various kinds of microparticles (which act as hosts for the probes and prevent dye leaching and aggregation), and then dispersing the microparticles in the thermogelating polymer. The resulting sensor gels were deposited on the surface of interest via spraying at temperatures of <20 degrees C At these temperatures, the gels adhere well to the target, even on uneven surfaces such as skin, wounds, and bacterial cultures. If temperature is risen to above 25 degrees C, the gels form a thin and soft but solid sensing layer which, however, can be simply removed from surface of interest by cooling and wiping it off, or by washing with water. Sprayable thermogelating sensors present obvious advantages over other sensors by not causing damage to the surface of interest. In our perception, the sensing materials also have wide further applicability in sensors for other species including clinically relevant gases, enzyme substrates (such as glucose or lactate) and ions. (C) 2015 Elsevier B.V. All rights reserved.

The intention of this compilation of articles was to introduce brand-new developments in the field of chemical imaging which have not been discussed in previous review articles. These include the design of new sensor nanomaterials based on photon uponversion crystals which convert near-infrared excitation light into sensor signals in the visible wavelength range highlighted by Christ and Schaferling. Sun, Ungerbock and Mayr describe the state of the art in oxygen imaging in microreactors and microfluidic devices. Miniaturized sensors for the imaging of oxygen, pH and temperature in microchips, microfluidic platforms and microbioreactors are reviewed by Pfeiffer and Nagl. Furthermore, Dmitriev and Papkovsky present a critical assessment of the applicability of probes for intracellular oxygen sensing. I hope these articles provide an interesting insight into advanced luminescent sensor materials and the applications of optical micro- and nanosensors in fluorescence imaging today and will be inspiring for the reader. Finally, I would like to thank all authors and referees for spending their time to enable this collection of articles.

A luminescent probe for determination of pH was designed based on a Forster resonance energy transfer (FRET) system, combining a europium chelate as the donor and carboxynaphtho-fluorescein as a pH sensitive acceptor. The FRET system enables referenced pH detection in an exceptional broad dynamic range from pH 3 to 9.

The design of photoluminescent molecular probes for the selective recognition of anions is a major challenge for the development of optical chemical sensors. The reversible binding of anions to lanthanide centers is one promising option for the realization of anion sensors, because it leads in some cases to a strong luminescence increase by the replacement of quenching water molecules. Yet, it is an open problem to gain control of the sensitivity and selectivity of the luminescence response. Primarily, the selective detection of (poly)phosphate species such as nucleotides has emerged as a demanding task, because they are involved in many biological processes and enzymatic reactions. We designed a series of pyridyl-based multidentate europium complexes (seven-, six-, and five-dentate) including sensitizing chromophores and studied their luminescence intensity and lifetime responses to different (poly)phosphates (adenosine triphosphate (ATP), adenosine diphosphate (ADP), adenosine monophosphate (AMP), cyclic adenosine monophosphate (cAMP), pyrophosphate, and phosphate anions), and carboxyanions (citrate, malate, oxalacetate, succinate, α-ketoglutarate, pyruvate, oxalate, carbonate). The results reveal that the number of free coordination sites has a significant impact on the sensitivity and selectivity of the response. Because of its reversibility, the lanthanide probes can be applied to monitor the activity of ATP-consuming enzymes such ATPases and apyrases, which is demonstrated by means of the five-dentate complex.