Additive manufacturing of metals produces material microstructures which are inherently different from those of wrought materials as they arise from a complex temperature history associated with the additive process. Because of complex microstructure morphologies and spatial heterogeneities, material properties are heterogeneous and reflect underlying microstructure. This paper describes a workflow for simulating the dynamic and spall response of additively manufactured metals. The approach consists of simulating microstructures associated with the additive manufacturing process, methods for representing spatially heterogeneous microstructures on a peridynamics discretization, and a specialized material model for handling dynamic material failure under spall conditions. Material properties are spatially distributed onto the discretization so that microstructure effects arising from additive manufacturing can be systematically incorporated into engineering-scale calculations. Model simulations are compared with laboratory flyer plate test data.

Peridigm is a meshfree peridynamics code written in C++ for use on large-scale parallel computers. It was originally developed at Sandia National Laboratories and is currently managed as an open-source, community driven software project. Its primary features include bond-based, state-based, and non-ordinary state-based constitutive models, bond failure laws, contact, and support for explicit and implicit time integration. To date, Peridigm has been used primarily by methods developers focused on solid mechanics and material failure. Peridigm utilizes foundational software components from Sandia’s Trilinos project and was designed for extensibility. This paper provides an overview of the solution methods implemented in Peridigm , a discussion of its software infrastructure, and demonstrates the use of Peridigm for the solution of several example problems.

This work describes a Metropolis Monte Carlo model for modeling additively manufactured metallic microstructures which employs Bézier curves to formulate melt pool geometry induced by a moving laser heat source. With this formulation, a wide range of melt pool geometries can be modeled and their effects on microstructure morphologies can be evaluated. Melt pool geometries are fit with Bézier curves using melt pool dimensions of width, length, and depth obtained from FEM calculations of the thermal process. Assuming a steady state pool geometry, microstructures are simulated incrementally in the heat affected zone in much the same way an additively manufactured material part is built. The approach is computationally tractable as microstructure simulation is only required in the fusion and heat affected zones, thus requiring less computational resources than would be needed if the entire material/part domain was taken into account. Using the model, microstructures are simulated for LENS™ processed stainless steel. Demonstrations show the model can replicate microstructure morphologies seen in electron beam backscatter diffraction data.

SPPARKS is an open-source parallel simulation code for developing and running various kinds of on-lattice Monte Carlo models at the atomic or meso scales. It can be used to study the properties of solid-state materials as well as model their dynamic evolution during processing. The modular nature of the code allows new models and diagnostic computations to be added without modification to its core functionality, including its parallel algorithms. A variety of models for microstructural evolution (grain growth), solid-state diffusion, thin film deposition, and additive manufacturing (AM) processes are included in the code. SPPARKS can also be used to implement grid-based algorithms such as phase field or cellular automata models, to run either in tandem with a Monte Carlo method or independently. For very large systems such as AM applications, the Stitch I/O library is included, which enables only a small portion of a huge system to be resident in memory. In this paper we describe SPPARKS and its parallel algorithms and performance, explain how new Monte Carlo models can be added, and highlight a variety of applications which have been developed within the code.

Additive manufactured Ti-5Al-5V-5Mo-3Cr (Ti-5553) is being considered as an AM repair material for engineering applications because of its superior strength properties compared to other titanium alloys. Here, we describe the failure mechanisms observed through computed tomography, electron backscatter diffraction (EBSD), and scanning electron microscopy (SEM) of spall damage as a result of tensile failure in as-built and annealed Ti-5553. We also investigate the phase stability in native powder, as-built and annealed Ti-5553 through diamond anvil cell (DAC) and ramp compression experiments. We then explore the effect of tensile loading on a sample containing an interface between a Ti-6Al-V4 (Ti-64) baseplate and additively manufactured Ti-5553 layer. Post-mortem materials characterization showed spallation occurred in regions of initial porosity and the interface provides a nucleation site for spall damage below the spall strength of Ti-5553. Preliminary peridynamics modeling of the dynamic experiments is described. Finally, we discuss further development of Stochastic Parallel PARticle Kinteic Simulator (SPPARKS) Monte Carlo (MC) capabilities to include the integration of alpha ( ? )-phase and microstructural simulations for this multiphase titanium alloy.

material following the heat treatment. The increased flow strength of the additively manufactured material relative to wrought counterparts is found to be due primarily to an increased dislocation density in the as-built material. However, the increased dislocation density does not completely account for the increased strength and it is hypothesized that some of the additional strength is related to the unique AM grain structure.

Thermal spray processes involve the repeated impact of millions of discrete particles, whose melting, deformation, and coating-formation dynamics occur at microsecond timescales. The accumulated coating that evolves over minutes is comprised of complex, multiphase microstructures, and the timescale difference between the individual particle solidification and the overall coating formation represents a significant challenge for analysts attempting to simulate microstructure evolution. In order to overcome the computational burden, researchers have created rule-based models (similar to cellular automata methods) that do not directly simulate the physics of the process. Instead, the simulation is governed by a set of predefined rules, which do not capture the finedetails of the evolution, but do provide a useful approximation for the simulation of coating microstructures. Here, we introduce a new rules-based process model for microstructure formation during thermal spray processes. The model is 3D, allows for an arbitrary number of material types, and includes multiple porositygeneration mechanisms. Example results of the model for tantalum coatings are presented along with sensitivity analyses of model parameters and validation against 3D experimental data. The model's computational efficiency allows for investigations into the stochastic variation of coating microstructures, in addition to the typical process-to-structure relationships.

Grain-scale microstructure evolution during additive manufacturing is a complex physical process. As with traditional solidification methods of material processing (e.g. casting and welding), microstructural properties are highly dependent on the solidification conditions involved. Additive manufacturing processes however, incorporate additional complexity such as remelting, and solid-state evolution caused by subsequent heat source passes and by holding the entire build at moderately high temperatures during a build. We present a three-dimensional model that simulates both solidification and solid-state evolution phenomena using stochastic Monte Carlo and Potts Monte Carlo methods. The model also incorporates a finite-difference based thermal conduction solver to create a fully integrated microstructural prediction tool. The three modeling methods and their coupling are described and demonstrated for a model study of laser powder-bed fusion of 300-series stainless steel. The investigation demonstrates a novel correlation between the mean number of remelting cycles experienced during a build, and the resulting columnar grain sizes.

components and improving the performance of AM materials. The AM fabrication process is characterized by building parts layer by layer using a selective laser melt process guided by a computer. A laser selectively scans and melts metal according to a designated geometry. As the laser scans, metal melts, fuses, and solidifies forming the final geometry in a layerwise fashion. As the laser heat source moves away, the metal cools and solidifies forming metallic microstructures. This work describes a microstructure modeling application implemented in the SPPARKS kinetic Monte Carlo computational framework for simulating the resulting microstructures. The application uses Bzier curves and surfaces to model the melt pool surface and spatial temperature profile induced by moving the laser heat source; it simulates the melting and fusing of metal at the laser hot spot and microstructure formation and evolution when the laser moves away. The geometry of the melt pool is quite flexible and we explore effects of variances in model parameters on simulated microstructures.