The active uranium neutron coincidence collar provides a means of non-destructively assaying the fissile linear density of Light Water Reactor fresh fuel assemblies containing low enriched uranium. These neutron collars can operate in two modes: a thermal and a fast mode. In fast mode, a neutron collar has an added cadmium (Cd) liner in the sample cavity of the detector to reduce the impact of the burnable poison (thermal neutron absorber) on the detector signal (doubles). The main advantage for operating in fast mode is a detected signal that is less dependent of the burnable neutron poison content and thus less dependent on facility operator declarations. The drawback is that operating in fast mode requires a longer measurement time (similar to hour vs tens of minutes for thermal mode) to achieve the statistically needed precision in the measurements. The trend in the modern reactor fuel assemblies is moving to higher burnup by using higher initial enrichment and, consequently, a higher number of burnable poison rods to compensate the initial neutron reactivity. The increase of the burnable poison loading has motivated the development of a new generation of high efficiency fast neutron collars to allow practical measurements in-field by nuclear inspectors. This paper describes the development and performance evaluation of a new generation of neutron collars, for both boiling water reactor (BWR) and pressurized water reactor (PWR) fuels, jointly developed between the US Department of Energy, through Los Alamos National Laboratory, and the Euratom Safeguards Directorate of the European Commission. We present here calibrations with reference fuel assemblies at Los Alamos National Laboratory as well as the results of in-field measurement campaigns in fuel fabrication plants with modern commercial fuel assemblies. The experimental results show that a typical PWR verification can be made in a total time of 30 min with an uncertainty in the measured mass of 2% at one standard deviation (1 sigma). A BWR verification can be made in 47 min with an uncertainty in the measured mass of 1.9% at 1 sigma, or a total time of 20 min with 1 sigma uncertainty in the measured mass of 2.5%.

The Fork detector is widely used by the safeguards inspectorate of the European Atomic Energy Community (EURATOM) and the International Atomic Energy Agency (IAEA) to verify spent nuclear fuel. Fork measurements are routinely performed for safeguards prior to dry storage cask loading. Additionally, spent fuel verification will be required at the facilities where encapsulation is performed for acceptance in the final repositories planned in Sweden and Finland. The use of the Fork detector as a quantitative instrument has not been prevalent due to the complexity of correlating the measured neutron and gamma ray signals with fuel inventories and operator declarations. A spent fuel data analysis module based on the ORIGEN burnup code was recently implemented to provide automated real-time analysis of Fork detector data. This module allows quantitative predictions of expected neutron count rates and gamma units as measured by the Fork detectors using safeguards declarations and available reactor operating data. This paper describes field testing of the Fork data analysis module using data acquired from 339 assemblies measured during routine dry cask loading inspection campaigns in Europe. Assemblies include both uranium oxide and mixed-oxide fuel assemblies. More recent measurements of 50 spent fuel assemblies at the Swedish Central Interim Storage Facility for Spent Nuclear Fuel are also analyzed. An evaluation of uncertainties in the Fork measurement data is performed to quantify the ability of the data analysis module to verify operator declarations and to develop quantitative go/no-go criteria for safeguards verification measurements during cask loading or encapsulation operations. The goal of this approach is to provide safeguards inspectors with reliable real-time data analysis tools to rapidly identify discrepancies in operator declarations and to detect potential partial defects in spent fuel assemblies with improved reliability and minimal false positive alarms. The results are summarized, and sources and magnitudes of uncertainties are identified, and the impact of analysis uncertainties on the ability to confirm operator declarations is quantified.

The Next Generation Safeguards Initiative Spent Fuel (NGSI-SF) Project started in 2009 with the intent to integrate nondestructive assay (NDA) signals in order to improve safeguards verification ca ...

The purpose of the Next Generation Safeguards Initiative (NGSI)–Spent Fuel (SF) project is to strengthen the technical toolkit of safeguards inspectors and/or other interested parties. The NGSI–SF team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detect the diversion or replacement of pins; (3) estimate the plutonium mass [which is also a function of the variables in (1)]; (4) estimate the decay heat; and (5) determine the reactivity of spent fuel assemblies. Since August 2013, a set of measurement campaigns has been conducted at the Central Interim Storage Facility for Spent Nuclear Fuel (Clab), in collaboration with Swedish Nuclear Fuel and Waste Management Company (SKB). One purpose of the measurement campaigns was to acquire passive gamma spectra with high-purity germanium and lanthanum bromide scintillation detectors from Pressurized Water Reactor and Boiling Water Reactor spent fuel assemblies. The absolute 137Cs count rate and the 154Eu/137Cs, 134Cs/137Cs, 106Ru/137Cs, and 144Ce/137Cs isotopic ratios were extracted; these values were used to construct corresponding model functions (which describe each measured quantity’s behavior over various combinations of burnup, cooling time, and initial enrichment) and then were used to determine those same quantities in each measured spent fuel assembly. The results obtained in comparison with the operator declared values, as well as the methodology developed, are discussed in detail in the paper.

A project to research the application of nondestructive assay (NDA) to spent fuel assemblies is underway. The research team comprises the European Atomic Energy Community (EURATOM), embodied by the European Commission, DG Energy, Directorate EURATOM Safeguards; the Swedish Nuclear Fuel and Waste Management Company (SKB); two universities; and several United States national laboratories. The Next Generation of Safeguards Initiative–Spent Fuel project team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detect the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. This study focuses on spectrally resolved gamma-ray measurements performed on a diverse set of 50 assemblies [25 pressurized water reactor (PWR) assemblies and 25 boiling water reactor (BWR) assemblies]; these same 50 assemblies will be measured with neutron-based NDA instruments and a full-length calorimeter. Given that encapsulation/repository and dry storage safeguards are the primarily intended applications, the analysis focused on the dominant gamma-ray lines of 137Cs, 154Eu, and 134Cs because these isotopes will be the primary gamma-ray emitters during the time frames of interest to these applications. This study addresses the impact on the measured passive gamma-ray signals due to the following factors: burnup, initial enrichment, cooling time, assembly type (eight different PWR and six different BWR fuel designs), presence of gadolinium rods, and anomalies in operating history. To compare the measured results with theory, a limited number of ORIGEN-ARP simulations were performed.

A project to research the application of non-destructive assay (NDA) techniques for spent fuel assemblies is underway at the Central Interim Storage Facility for Spent Nuclear Fuel (for which the S ...

This research focused on the analysis of a set of stationary passive gamma measurements taken on the spent nuclear fuel assemblies from a boiling water reactor (BWR) using pulse height analysis data acquisition. The measurements were performed on 25 different BWR assemblies in 2014 at Sweden's Central Interim Storage Facility for Spent Nuclear Fuel (Clab). This study was performed as part of the Next Generation of Safeguards Initiative Spent Fuel project to research the application of nondestructive assay (NDA) to spent fuel assemblies. The NGSI-SF team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay (NDA) measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detect the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. The final objective of this project is to quantify the capability of several integrated NDA instruments to meet the aforementioned goals using the combined signatures of neutrons, gamma rays, and heat.This report presents a selection of the measured data and summarizes an analysis of the results. Specifically, trends in the count rates measured for spectral lines from the following isotopes were analyzed as a function of the declared burnup and cooling time: Cs-137, Eu-154, Cs-134, and to a lesser extent, Ru-106 and Ce-144. From these measured count rates, predictive algorithms were developed to enable the estimation of the burnup and cooling time. Furthermore, these algorithms were benchmarked on a set of assemblies not included in the standard assemblies set used by this research team. Published by Elsevier B.V.

A project to research the application of non-destructive assay (NDA) to spent fuel assemblies is underwayamong a team comprised of the European Commission, DG Energy, Directorate Safeguards; the Sw ...

Neutron coincidence counting and neutron multiplicity counting are standard techniques for mass determination of fissile materials in nuclear safeguards applications. The preferred neutron detector layout incorporates 3He gas proportional counters in a cylindrical polyethylene moderator block with a central sample cavity. The detector tubes are embedded in the polyethylene in a ring shape approximating a 4 geometry. This standard layout has been adopted in several detector designs such as the High Level Neutron Coincidence Counter (HLNCC-II). The recent worldwide shortage of 3He gas has prompted research into alternative detection technologies for neutrons. An obvious candidate from a physics point of view is 10B due to the high thermal neutron cross section and the inexpensive enrichment process of the 10B isotope. An important advantage includes the fact that when in form of boron trifluoride gas this neutron detector the can replace 3He gas tubes while maintaining other standard counter materials, the well counter design, and even the detector electronics. The toxicity of the BF3 gas however has been mentioned as a potential problem for using this neutron detector is large size neutron coincidence or multiplicity counters in nuclear facilities. The paper describes the newly developed prototype well counter based on BF3 detector tubes including a discussion of results of test bed experiments and Monte Carlo simulations carried out to reach the final design. The objective to build a working counter with same cavity dimensions as the standard HLNCC but with neutron detection efficiency high enough to allow neutron multiplicity counting in practical applications was achieved. The paper shows initial results of measurements with the counter as well as the measured assay parameters. The paper also shows how the issue of the toxicity of the gas has been addressed in the design of the new counter. URI: Authors: PEDERSEN Bent CROCHEMORE Jean-Michel MOSCONI Marita MAYOROV Valeriy TAGZIRIA Hamid OCHERASHVILI Aharon ROESGEN Eric SCHWALBACH Peter Publication Year: 2015 Science Areas: Nuclear safety and security [1]

Nondestructive Assay Data Integration with the SKB-50 Assemblies - Starting with Passive Gamma and Total Neutron Data

The Swedish Nuclear Fuel and Waste Management Company (SKB), European Atomic Energy Community (Euratom), two universities and several U.S. Department of Energy Laboratories have joined in a collaborative research effort to determine the capability of non-destructive assay (NDA) techniques to meet the combined needs of the safeguards community and the Swedish encapsulation and repository facilities operator SKB. These needs include partial defect detection, heat quantification, assembly identification (initial enrichment, burnup and cooling time), and Pu mass and reactivity determination. The experimental component of this research effort involves the measurement of 50 assemblies at the Central Storage of Spent Nuclear Fuel (Clab) facility in Sweden, 25 of which were irradiated in Pressurized Water Reactors and 25 in Boiling Water Reactors. The experimental signatures being measured for all assemblies include spectral resolved gammas (HPGe and LaBr3), time correlated neutrons (Differential Die-away Self Interrogation), time-varying and continuous active neutron interrogation (Differential Die-away and an approximation of Californium Interrogation Prompt Neutron), total neutron and total gamma fluxes (Fork Detector), total heat (assembly length calorimeter) and possibly the Cerenkov light emission (Digital Cerenkov Viewing Device). This paper fits into the IAEA’s Department of Safeguards Long-Term R&D Plan in the context of developing “more sensitive and less intrusive alternatives to existing NDA instruments to perform partial defect test on spent fuel assembly prior to transfer to difficult to access storage,” as well as potentially supporting pyrochemical processing. The work describes the specific measured signatures, the uniqueness of the information contained in these signatures and why a data mining approach is being used to combine the various signatures to optimally satisfy the various needs of the collaboration. This paper will address efficient and effective verification strategies particularly in the context of encapsulation and repository facilities.