As Moore's law is running to its physical limit, tomorrow's electronic systems can be leveraged to a higher value by integrating "More than Moore" technologies into CMOS digital circuits. The hybrid heterostructure composed of two-dimensional (2D) semiconductors and molecular materials represents a powerful strategy to confer new properties to the former components, realize stimuli-responsive functional devices, and enable diversification in "More than Moore" technologies. Here, an ionic liquid (IL) gated 2D MoS2 field-effect transistor (FET) with molecular functionalization is fabricated. The suitably designed ferrocene-substituted alkanethiol molecules not only improve the FET performance, but also show reversible electrochemical switching on the surface of MoS2 . Field-effect mobility of monolayer MoS2 reaches values as high as ≈116 cm2 V-1 s-1 with Ion /Ioff ratio exceeding 105 . Molecules in their neutral or charged state impose distinct doping effect, efficiently tuning the electron density in monolayer MoS2 . It is noteworthy that the joint doping effect from IL and switchable molecules results in the steep subthreshold swing of MoS2 FET in the backward sweep. These results demonstrate that the device architecture represents an unprecedented and powerful strategy to fabricate switchable 2D FET with a chemically programmed electrochemical signal as a remote control, paving the road toward novel functional devices.

The pervasiveness of information technologies is generating an impressive amount of data, which need to be accessed very quickly. Nonvolatile memories (NVMs) are making inroads into high-capacity storage to replace hard disk drives, fuelling the expansion of the global storage memory market. As silicon-based flash memories are approaching their fundamental limit, vertical stacking of multiple memory cell layers, innovative device concepts, and novel materials are being investigated. In this context, emerging 2D materials, such as graphene, transition metal dichalcogenides, and black phosphorous, offer a host of physical and chemical properties, which could both improve existing memory technologies and enable the next generation of low-cost, flexible, and wearable storage devices. Herein, an overview of graphene and related 2D materials (GRMs) in different types of NVM cells is provided, including resistive random-access, flash, magnetic and phase-change memories. The physical and chemical mechanisms underlying the switching of GRM-based memory devices studied in the last decade are discussed. Although at this stage most of the proof-of-concept devices investigated do not compete with state-of-the-art devices, a number of promising technological advancements have emerged. Here, the most relevant material properties and device structures are analyzed, emphasizing opportunities and challenges toward the realization of practical NVM devices.

Two-dimensional (2D) transition-metal dichalcogenides (TMDs) recently emerged as novel materials displaying a wide variety of physicochemical properties that render them unique scaffolds for high-performance (opto)electronics. The controlled physisorption of molecules on the TMD surface is a viable approach for tuning their optical and electronic properties. Solvents, made of small aromatic molecules, are frequently employed for the cleaning of the 2D materials or as a "dispersant" for their chemical functionalization with larger (macro)molecules, without considering their potential key effect in locally modifying the characteristics of 2D materials. In this work, we demonstrate how the electronic and optical properties of a mechanically exfoliated monolayer of MoS2 and WSe2 are modified when physically interacting with small aromatic molecules of common solvents. Low-temperature photoluminescence (PL) spectra recorded at 78 K revealed that physisorbed benzene derivatives could modulate the charge carrier density in monolayer TMDs, hence affecting the switching between a neutral exciton and trion (charged exciton). By combining experimental evidence with density functional theory calculations, we confirm that charge-transfer doping on TMDs depends not only on the difference in chemical potential between molecules and 2D materials but also on the thermodynamic stability of physisorption. Our results provide unambiguous evidences of the great potential of optical and electrical tuning of monolayer MoS2 and WSe2 by physisorption of small aromatic solvent molecules, which is highly relevant for both fundamental studies and device application purposes.

Stimuli-responsive hybrid van der Waals heterostructures (vdWHs), composed of organic molecular switches superimposed on inorganic 2D materials (2DMs), can combine the outstanding physical properties of the latter components with the virtually infinite variety of tunable functionality of molecules, thereby offering an efficient protocol for the development of high-performance multifunctional materials and devices. The use of light as a remote control to modulate the properties of semiconducting 2DMs when interfaced with photochromic molecules suffers from both the limitation associated with the persistent photoconductivity characterizing the 2DMs and the finite thermal stability of the photochromic molecule in its different states. Here, we have devised a universal approach toward the fabrication of optically switchable electronic devices comprising a few nanometers thick azobenzene (AZO) layer physisorbed on 2D semiconductors supported on a trap-free polymer dielectric. The joint effect of the improved 2D/dielectric interface, the molecule's light-modulated dipolar doping, and the high thermal stability of cis-AZO offers the highest control over the reversible and efficient charge carrier tuning in 2D semiconductors with a preserved high performance in 2D field-effect transistors, as quantified in terms of carrier mobility and Ion/ Ioff ratio. The device has the potential to operate as an optical memory with four current levels and long retention time (>15 h). Furthermore, by using a CMOS-compatible micropatterning process, the photoswitchable resistor-diode transition has been achieved on hybrid lateral heterojunction devices. Our approach is of general applicability toward the generation of high-performance hybrid vdWHs for the emergence of functional and responsive devices.

The spatially precise integration of arrays of micropatterned two-dimensional (2D) crystals onto three-dimensionally structured Si/SiO2 substrates represents an attractive, low-cost system-on-chip strategy toward the realization of extended functions in silicon microelectronics. However, the reliable integration of such atomically thin arrays on planar patterned surfaces has proven challenging due to their poor adhesion to underlying substrates, as ruled by weak van der Waals interactions. Here, we report on an integration method utilizing the flexibility of the atomically thin crystals and their physical subsidence in liquids, which enables the reliable fabrication of the micropatterned 2D materials/Si arrays. Our photodiode devices display peak sensitivity as high as 0.35 A/W and external quantum efficiency (EQE) of ∼90%. The nano-subsidence technique represents a viable path to on-chip integration of 2D crystals onto silicon for advanced microelectronics.

The original version of this article incorrectly listed an affiliation of Sara Bonacchi as 'Present address: Institut National de la Recherche Scientifique (INRS), EMT Center, Boulevard Lionel-Boulet, Varennes, QC, J3X 1S2, 1650, Canada', instead of the correct 'Present address: Department of Chemical Sciences - University of Padua - Via Francesco Marzolo 1 - 35131 Padova - Italy'. And an affiliation of Emanuele Orgiu was incorrectly listed as 'Present address: Department of Chemical Sciences, University of Padua, Via Francesco Marzolo 1, Padova, 35131, Italy', instead of the correct 'Present address: Institut National de la Recherche Scientifique (INRS), EMT Center, Boulevard Lionel-Boulet, Varennes, QC, J3X 1S2, 1650, Canada'. This has been corrected in both the PDF and HTML versions of the article.

Two-dimensional (2D) transition metal dichalcogenides (TMDs) are continuously attracting attention for both fundamental studies and technological applications. The physical and chemical properties of ultrathin TMD sheets are extraordinarily different from those of the corresponding bulk materials and for this reason their production is a stimulating topic, especially when the preparation method enables to obtain a remarkable yield of nanosheets with large area and high quality. Herein, we present a fast ( < 1 h) electrochemical exfoliation of molybdenum disulfide (MoS2) via lithium-ion intercalation, by using a solution of lithium chloride in dimethyl sulfoxide (DMSO). Unlike the conventional intercalation methods based on dangerous organolithium compounds, our approach leads to the possibility to obtain mono-, bi- and tri-layer thick MoS2 nanosheets with a large fraction of the semiconducting 2H phase ( similar to 60%), as estimated by X-ray photoelectron spectroscopy (XPS). The electrical properties of the exfoliated material were investigated through the fabrication and characterization of back-gated field-effect transistors (FETs) based on individual MoS2 nanosheets. As-fabricated devices displayed unipolar semiconducting behavior (n-type) with field-effect mobility mu(FE) <= 10(-3) cm(2) V-1 s(-1) and switching ratio I-on/I-off <= 10, likely limited by 1T/2H polymorphism and defects (e.g. sulfur vacancies) induced during the intercalation/exfoliation process. A significant enhancement of the electrical performances could be achieved through a combination of vacuum annealing (150 degrees C) and sulfur-vacancy healing with vapors of short-chain alkanethiols, resulting in mu(FE) up to 2 x 10(-2) cm(2) V-1 s(-1) and I-on/I-off approximate to 100. Our results pave the way towards the fast preparation - under ambient conditions - of semiconducting MoS2 nanosheets, suitable for application in low cost (opto-)electronic devices.

Two-dimensional (2D) semiconductors, such as ultrathin layers of transition metal dichalcogenides (TMDs), offer a unique combination of electronic, optical and mechanical properties, and hold potential to enable a host of new device applications spanning from flexible/wearable (opto)electronics to energy-harvesting and sensing technologies. A critical requirement for developing practical and reliable electronic devices based on semiconducting TMDs consists in achieving a full control over their charge-carrier polarity and doping. Inconveniently, such a challenging task cannot be accomplished by means of well-established doping techniques (e.g. ion implantation and diffusion), which unavoidably damage the 2D crystals resulting in degraded device performances. Nowadays, a number of alternatives are being investigated, including various (supra)molecular chemistry approaches relying on the combination of 2D semiconductors with electroactive donor/acceptor molecules. As yet, a large variety of molecular systems have been utilized for functionalizing 2D TMDs via both covalent and non-covalent interactions. Such research endeavours enabled not only the tuning of the charge-carrier doping but also the engineering of the optical, electronic, magnetic, thermal and sensing properties of semiconducting TMDs for specific device applications. Here, we will review the most enlightening recent advancements in experimental (supra)molecular chemistry methods for tailoring the properties of atomically-thin TMDs - in the form of substrate-supported or solution-dispersed nanosheets - and we will discuss the opportunities and the challenges towards the realization of novel hybrid materials and devices based on 2D semiconductors and molecular systems.

Electrochemically exfoliated graphene (EEG) possesses optical and electronic properties that are markedly different from those of the more explored graphene oxide in both its pristine and reduced forms. EEG also holds a unique advantage compared to other graphenes produced by exfoliation in liquid media: it can be obtained in large quantities in a short time. However, an in-depth understanding of the structure properties relationship of this material is still lacking. In this work, we report physicochemical characterization of EEG combined with an investigation of the electronic properties of this material carried out both at the single flake level and on the films. Additionally, we use for the first time microwave irradiation to reduce the EEG and demonstrate that the oxygen functionalities are not the bottleneck for charge transport in EEG, which is rather hindered by the presence of structural defects within the basal plane.

Irradiation of 2D sheets of transition metal dichalcogenides with ion beams has emerged as an effective approach to engineer chemically active defects in 2D materials. In this context, argon-ion bombardment has been utilized to introduce sulfur vacancies in monolayer molybdenum disulfide (MoS2 ). However, a detailed understanding of the effects of generated defects on the functional properties of 2D MoS2 is still lacking. In this work, the correlation between critical electronic device parameters and the density of sulfur vacancies is systematically investigated through the fabrication and characterization of back-gated monolayer MoS2 field-effect transistors (FETs) exposed to a variable fluence of low-energy argon ions. The electrical properties of pristine and ion-irradiated FETs can be largely improved/recovered by exposing the devices to vapors of short linear thiolated molecules. Such a solvent-free chemical treatment-carried out strictly under inert atmosphere-rules out secondary healing effects induced by oxygen or oxygen-containing molecules. The results provide a guideline to design monolayer MoS2 optoelectronic devices with a controlled density of sulfur vacancies, which can be further exploited to introduce ad hoc molecular functionalities by means of thiol chemistry approaches.

Graphene is a monolayer of carbon atoms arranged in a honeycomb lattice with extraordinary mechanical, electrical and optical properties that attracts the interests of the researchers and industries’ since nearly a decade. Despite its promising properties, graphene has not yet found an extensive use in everyday life applications due to the limitations of its up-scalable production. [1] Approaches such as scotch tape exfoliation, epitaxial growth and chemical vapor deposition are not suitable for industrial production, because of high cost and/or low yield. Alongside of these methods, exfoliation processes in liquid media, including ultrasound induced liquid-phase exfoliation (UILPE) and electrochemical exfoliation (EE), are nowadays well established and potentially up-scalable approaches. [2] For instance, in laboratory, gram scale quantities of graphene are electrochemically produced in several minutes, employing low-cost equipment and working in eco-friendly environments. Moreover electrochemical exfoliation lead to micrometer size graphene flakes, encouraging a complete and rapid characterization of produced material at single flake level that is problematic in the case of nanometer sized graphene produced by sonication. A fast preliminary investigation by optical microcopy, analyzing the optical contrast between graphene sheets and proper substrates, can be performed to identify the presence of monoand few-layered graphene. It can be followed by statistical thickness and flake size analysis by Atomic Force Microscopy (AFM), which supply also information on the morphology of the flake, and the eventual presence of in plane defects. Raman spectroscopy is also performed to further probe the quality of the exfoliated material. Recent studies shows the effect of different operating parameters (starting graphitic material, [3] type of electrolyte [4] and time of electrolysis [5]) on quality and yield of electrochemically exfoliated graphene. We here investigate the influence of applied potential and time of electrolysis on the oxidation degree of graphene produced in anodic condition. For the first time such effects are correlated with charge carrier mobility in graphene, exploring the electrical performance of FETs devices based on EEG single sheet. This work open up new perspectives to the potential introduction of graphene exfoliated in liquid media as active material in electronic industry. Moreover it proves the tunability of EEG properties, which can be tailored to meet the demands of many applications, in the field of electronics as well as composites, energy storage and conversion, etc.

CONSPECTUS: Atomic crystals of two-dimensional materials consisting of single sheets extracted from layered materials are gaining increasing attention. The most well-known material from this group is graphene, a single layer of graphite that can be extracted from the bulk material or grown on a suitable substrate. Its discovery has given rise to intense research effort culminating in the 2010 Nobel Prize in physics awarded to Andre Geim and Konstantin Novoselov. Graphene however represents only the proverbial tip of the iceberg, and increasing attention of researchers is now turning towards the veritable zoo of so-called “other 2D materials”. They have properties complementary to graphene, which in its pristine form lacks a bandgap: MoS2, for example, is a semiconductor, while NbSe2 is a superconductor. They could hold the key to important practical applications and new scientific discoveries in the two-dimensional limit. This family of materials has been studied since the 1960s, but most of the research focused on their tribological applications: MoS2 is best known today as a high-performance dry lubricant for ultrahigh-vacuum applications and in car engines. The realization that single layers of MoS2 and related materials could also be used in functional electronic devices where they could offer advantages compared with silicon or graphene created a renewed interest in these materials. MoS2 is currently gaining the most attention because the material is easily available in the form of a mineral, molybdenite, but other 2D transition metal dichalcogenide (TMD) semiconductors are expected to have qualitatively similar properties. In this Account, we describe recent progress in the area of single-layer MoS2-based devices for electronic circuits. We will start with MoS2 transistors, which showed for the first time that devices based on MoS2 and related TMDs could have electrical properties on the same level as other, more established semiconducting materials. This allowed rapid progress in this area and was followed by demonstrations of basic digital circuits and transistors operating in the technologically relevant gigahertz range of frequencies, showing that the mobility of MoS2 and TMD materials is sufficiently high to allow device operation at such high frequencies. Monolayer MoS2 and other TMDs are also direct band gap semiconductors making them interesting for realizing optoelectronic devices. These range from simple phototransistors showing high sensitivity and low noise, to light emitting diodes and solar cells. All the electronic and optoelectronic properties of MoS2 and TMDs are accompanied by interesting mechanical properties with monolayer MoS2 being as stiff as steel and 30× stronger. This makes it especially interesting in the context of flexible electronics where it could combine the high degree of mechanical flexibility commonly associated with organic semiconductors with high levels of electrical performance. All these results show that MoS2 and TMDs are promising materials for electronic and optoelectronic applications.

Two-dimensional (2D) semiconductors, consisting of single-sheets of layered transition metal dichalcogenides (TMD), are attracting enormous interest from both fundamental science and technology. Monolayer molybdenum disulfide (MoS2), a typical example from this class of materials, is currently under intense research investigation because its direct band gap, atomic-scale thickness and mechanical flexibility could enable a wide range of novel technological applications, such as low-power flexible/transparent electronics, displays and wearable sensors. Critical to all these applications are the material mechanical strength, the mobility of charge-carriers in the 2D semiconductor and its interaction with the surrounding environment. This thesis describes experimental research conducted on these critical aspects and shows a proof-of-concept device application based on heterostructures of MoS2 and graphene. The main goal of the research was to assess experimentally the potential of monolayer MoS2 for application in flexible electronics. The thesis is based on three papers. The first paper describes the measurements of the in-plane stiffness and breaking strength of free-standing membranes of monolayer MoS2. Nanoindentation experiments were performed with the tip of an atomic force microscope (AFM) to extract the material's Young's modulus (E 270 GPa) and breaking strength (Iƒmax 23 GPa). Breaking occurred at maximum internal strain Iµint 11%, which indicates that monolayer MoS2 is suitable for integration on flexible plastic substrates. The second paper represents the core work of this thesis. It explores the charge transport properties of monolayer MoS2 supported by different dielectric substrates, such as thin polymer films of parylene, atomically flat sapphire and 2D sheets of hexagonal boron nitride (h-BN). It was found that substrate surface corrugations do not represent a major limit to charge-carrier mobility in monolayer MoS2, which seems at this stage dominated by impurities and material's defects. Field-effect transistors with mobility 100 cm2/Vs and on/off current ratio Ion/Ioff > 10^5 were successfully integrated on parylene substrates, whose root-mean-square roughness Rq can be more than two times larger than the thickness of the transistor channel itself. Because parylene is also a flexible material, this work showed a viable method for the realization of high-mobility and high performance flexible devices based on 2D semiconductors. Finally, the third paper describes a flash-memory cell fabricated using monolayer MoS2/graphene heterostructures and dielectric layers of HfO2 grown by atomic layer deposition (ALD). The architecture of the device resembles that of a floating-gate transistor. Monolayer MoS2 acts as the transistor channel, graphene electrodes are used to collect and inject the charge carriers, and a piece of multilayer graphene serves as ultrathin charge trapping layer. In this paper, it was shown that graphene contacts to monolayer MoS2 result in ohmic-like current-voltage characteristics at room temperature. Moreover, the use of graphene and 2D semiconductors in flash memory technology was indicated as a potential strategy for further scaling of memory cells and for their integration in flexible electronic devices.

Two-dimensional semiconductors such as MoS2 are an emerging material family with wide-ranging potential applications in electronics, optoelectronics, and energy harvesting. Large-area growth methods are needed to open the way to applications. Control over lattice orientation during growth remains a challenge. This is needed to minimize or even avoid the formation of grain boundaries, detrimental to electrical, optical, and mechanical properties of MoS2 and other 2D semiconductors. Here, we report on the growth of high-quality monolayer MoS2 with control over lattice orientation. We show that the monolayer film is composed of coalescing single islands with limited numbers of lattice orientation due to an epitaxial growth mechanism. Optical absorbance spectra acquired over large areas show significant absorbance in the high-energy part of the spectrum, indicating that MoS2 could also be interesting for harvesting this region of the solar spectrum and fabrication of UV-sensitive photodetectors. Even though the interaction between the growth substrate and MoS2 is strong enough to induce lattice alignment via van der Waals interaction, we can easily transfer the grown material and fabricate devices. Local potential mapping along channels in field-effect transistors shows that the single-crystal MoS2 grains in our film are well connected, with interfaces that do not degrade the electrical conductivity. This is also confirmed by the relatively large and length-independent mobility in devices with a channel length reaching 80 μm.

CONSPECTUS: Atomic crystals of two-dimensional materials consisting of single sheets extracted from layered materials are gaining increasing attention. The most well-known material from this group is graphene, a single layer of graphite that can be extracted from the bulk material or grown on a suitable substrate. Its discovery has given rise to intense research effort culminating in the 2010 Nobel Prize in physics awarded to Andre Geim and Konstantin Novoselov. Graphene however represents only the proverbial tip of the iceberg, and increasing attention of researchers is now turning towards the veritable zoo of so-called "other 2D materials". They have properties complementary to graphene, which in its pristine form lacks a bandgap: MoS2, for example, is a semiconductor, while NbSe2 is a superconductor. They could hold the key to important practical applications and new scientific discoveries in the two-dimensional limit. This family of materials has been studied since the 1960s, but most of the research focused on their tribological applications: MoS2 is best known today as a high-performance dry lubricant for ultrahigh-vacuum applications and in car engines. The realization that single layers of MoS2 and related materials could also be used in functional electronic devices where they could offer advantages compared with silicon or graphene created a renewed interest in these materials. MoS2 is currently gaining the most attention because the material is easily available in the form of a mineral, molybdenite, but other 2D transition metal dichalcogenide (TMD) semiconductors are expected to have qualitatively similar properties. In this Account, we describe recent progress in the area of single-layer MoS2-based devices for electronic circuits. We will start with MoS2 transistors, which showed for the first time that devices based on MoS2 and related TMDs could have electrical properties on the same level as other, more established semiconducting materials. This allowed rapid progress in this area and was followed by demonstrations of basic digital circuits and transistors operating in the technologically relevant gigahertz range of frequencies, showing that the mobility of MoS2 and TMD materials is sufficiently high to allow device operation at such high frequencies. Monolayer MoS2 and other TMDs are also direct band gap semiconductors making them interesting for realizing optoelectronic devices. These range from simple phototransistors showing high sensitivity and low noise, to light emitting diodes and solar cells. All the electronic and optoelectronic properties of MoS2 and TMDs are accompanied by interesting mechanical properties with monolayer MoS2 being as stiff as steel and 30× stronger. This makes it especially interesting in the context of flexible electronics where it could combine the high degree of mechanical flexibility commonly associated with organic semiconductors with high levels of electrical performance. All these results show that MoS2 and TMDs are promising materials for electronic and optoelectronic applications.

Atomically thin molybdenum disulfide (MoS2) offers potential for advanced devices and an alternative to graphene due to its unique electronic and optical properties. The temperature-dependent Raman spectra of exfoliated, monolayer MoS2 in the range of 100-320 K are reported and analyzed. The linear temperature coefficients of the in-plane E2g 1 and the out-of-plane A1g modes for both suspended and substrate-supported monolayer MoS2 are measured. These data, when combined with the first-order coefficients from laser power-dependent studies, enable the thermal conductivity to be extracted. The resulting thermal conductivity κ = (34.5(4) W/mK at room temperature agrees well with the first principles lattice dynamics simulations. However, this value is significantly lower than that of graphene. The results from this work provide important input for the design of MoS2-based devices where thermal management is critical.

Conventional floating-gate (FG) transistors (made with Si/poly-Si) that form the building blocks of the widely employed nonvolatile flash memory technology face severe scaling challenges beyond the 12-nm node. In this paper, for the first time, a comprehensive evaluation of the FG transistor made from emerging nanocrystals in the form of 2-dimensional (2D) transition metal dichalcogenides (TMDs) and multilayer graphene (MLG) is presented. It is shown that TMD based 2D channel materials have excellent gate length scaling potential due to their atomic scale thicknesses. On the other hand, employing MLG as FG greatly reduces cell-to-cell interference and alleviates reliability concerns. Moreover, it is also revealed that TMD/MLG heterostructures enable new mechanism for improving charge retention, thereby allowing the effective oxide thickness of gate dielectrics to be scaled to a few nanometers. Thus, this work indicates that judiciously selected 2D-nanocrystals can significantly extend the lifetime of the FG-based memory cell.

CONSPECTUS: Atomic crystals of two-dimensional materials consisting of single sheets extracted from layered materials are gaining increasing attention. The most well-known material from this group is graphene, a single layer of graphite that can be extracted from the bulk material or grown on a suitable substrate. Its discovery has given rise to intense research effort culminating in the 2010 Nobel Prize in physics awarded to Andre Geim and Konstantin Novoselov. Graphene however represents only the proverbial tip of the iceberg, and increasing attention of researchers is now turning towards the veritable zoo of so-called “other 2D materials”. They have properties complementary to graphene, which in its pristine form lacks a bandgap: MoS2, for example, is a semiconductor, while NbSe2 is a superconductor. They could hold the key to important practical applications and new scientific discoveries in the two-dimensional limit. This family of materials has been studied since the 1960s, but most of the research focused on their tribological applications: MoS2 is best known today as a high-performance dry lubricant for ultrahigh-vacuum applications and in car engines. The realization that single layers of MoS2 and related materials could also be used in functional electronic devices where they could offer advantages compared with silicon or graphene created a renewed interest in these materials. MoS2 is currently gaining the most attention because the material is easily available in the form of a mineral, molybdenite, but other 2D transition metal dichalcogenide (TMD) semiconductors are expected to have qualitatively similar properties. In this Account, we describe recent progress in the area of single-layer MoS2-based devices for electronic circuits. We will start with MoS2 transistors, which showed for the first time that devices based on MoS2 and related TMDs could have electrical properties on the same level as other, more established semiconducting materials. This allowed rapid progress in this area and was followed by demonstrations of basic digital circuits and transistors operating in the technologically relevant gigahertz range of frequencies, showing that the mobility of MoS2 and TMD materials is sufficiently high to allow device operation at such high frequencies. Monolayer MoS2 and other TMDs are also direct band gap semiconductors making them interesting for realizing optoelectronic devices. These range from simple phototransistors showing high sensitivity and low noise, to light emitting diodes and solar cells. All the electronic and optoelectronic properties of MoS2 and TMDs are accompanied by interesting mechanical properties with monolayer MoS2 being as stiff as steel and 30× stronger. This makes it especially interesting in the context of flexible electronics where it could combine the high degree of mechanical flexibility commonly associated with organic semiconductors with high levels of electrical performance. All these results show that MoS2 and TMDs are promising materials for electronic and optoelectronic applications.