High amplitude energetic particle geodesic acoustic mode (EGAM) oscillations driven by Neutral Beam (NBI) injected in the direction counter to the toroidal plasma current are observed in the TCV tokamak. The modes appear at frequencies close to the geodesic acoustic mode (GAM) frequency, corresponding to the mode radii calculated without plasma elongation corrections. The spatial structure of the EGAM density oscillation is analyzed using multichannel soft x-ray (SXR) and broadband light emission diagnostics. The analysis of spatiotemporal emission data shows a non-rotating structure of the density oscillations. The non-rotating mode discrimination is the additional new capability of the multichannel spatiotemporal SXR data analysis technique in TCV. We present the discrimination method of assessing the standing character of the EGAM wave. The structure of EGAM density oscillations in TCV is consistent with the theoretical GAM poloidal structure, namely a m= 1 standing wave with density oscillations amplitude proportional to sin(theta), where the poloidal angle theta is measured from the equatorial plane. The poloidal structure of magnetic the field oscillations is analyzed using a poloidal array of magnetic coils. The structure of the EGAM-induced magnetic field oscillations in TCV is a m = 2 standing wave. Time evolution of EGAMs suggests that a nonlinear EGAM chirping is observed. The chirping depends on the EGAM radial location, which varies as the NBI deposition is varied through a vertical shift of the plasma magnetic axis. The chirping disappears at the plasma periphery. A fast periodic radial shift of the EGAMs radial location is also observed to occur during the single chirp.

Future large tokamaks will operate at high plasma currents and high stored plasma energies. To ensure machine protection in case of a sudden loss of plasma confinement (major disruption), a large fraction of the magnetic and thermal energy must be radiated to reduce thermal loads. The disruption mitigation system for ITER is based on massive material injection in the form of shattered pellet injection (SPI). To support ITER, a versatile SPI system was installed at the tokamak ASDEX Upgrade (AUG). The AUG SPI features three independent pellet generation cells and guide tubes, and each was equipped with different shatter heads for the 2022 experimental campaign. We dedicated over 200 plasma discharges to the study of SPI plasma termination, and in this manuscript report on the results of bolometry (total radiation) analysis. We found, that the amount of neon inside the pellets is the dominant factor determining the radiated energy fraction ( frad). Large and fast fragments, produced by the 12.5 degrees rectangular shatter head, lead to somewhat higher values of frad compared to the 25 degrees circular or rectangular heads. This effect is strongest for neon content of less than or similar to 3x1020 neon atoms ( fneon less than or similar to 1.25% neon) injected, where a lower normal velocity component (larger fragments) seems slightly beneficial. While full-sized, 8 mm diameter, 100% deuterium ( D2) pellets lead to a disruption, the 4 mm or shortened 8 mm pellets of 100% D2 did not. The disruption threshold for 100% D2 is found to be around 1x1022 deuterium molecules inside the pellet. While the radiated energy fraction of non-disruptive SPI is below 20%, this is increased to 40% during the thermal quench and vertical displacement event phase of the disruptive injections. For deuterium-neon-mix pellets, frad-values of <= 90% are observed, and the curve saturates around 80% already for 10% neon mixed into the 8 mm pellets ( 2x1021 neon atoms).

We present a model for the particle balance in the post-disruption runaway electron plateau phase of a tokamak discharge. The model is constructed with the help of, and applied to, experimental data from TCV discharges investigating the so-called ‘low- Z benign termination’ runaway electron mitigation scheme. In the benign termination scheme, the free electron density is first reduced in order for a subsequently induced MHD instability to grow rapidly and spread the runaway electrons widely across the wall. We show that the observed non-monotonic dependence of the free electron density with the measured neutral pressure is due to plasma re-ionization induced by runaway electron impact ionization. At higher neutral pressures, more target particles are present in the plasma for runaway electrons to collide with and ionize. Parameter scans are conducted to clarify the role of the runaway electron density and energy on the free electron density, and it is found that only the runaway electron density has a noticeable impact. While the free electron density is shown to be related to the spread of heat fluxes at termination, the exact cause for the upper neutral pressure limit remains undetermined and an object for further study.

Tokamak a configuration variable (TCV), recently celebrating 30 years of near-continual operation, continues in its missions to advance outstanding key physics and operational scenario issues for ITER and the design of future power plants such as DEMO. The main machine heating systems and operational changes are first described. Then follow five sections: plasma scenarios. ITER Base-Line (IBL) discharges, triangularity studies together with X3 heating and N2 seeding. Edge localised mode suppression, with a high radiation region near the X-point is reported with N-2 injection with and without divertor baffles in a snowflake configuration. Negative triangularity (NT) discharges attained record, albeit transient, beta(N) similar to 3 with lower turbulence, higher low-Z impurity transport, vertical stability and density limits and core transport better than the IBL. Positive triangularity L-Mode linear and saturated ohmic confinement confinement saturation, often-correlated with intrinsic toroidal rotation reversals, was probed for D, H and He working gases. H-mode confinement and pedestal studies were extended to low collisionality with electron cyclotron heating obtaining steady state electron iternal transport barrier with neutral beam heating (NBH), and NBH driven H-mode configurations with off-axis co-electron cyclotron current drive. Fast particle physics. The physics of disruptions, runaway electrons and fast ions (FIs) was developed using near-full current conversion at disruption with recombination thresholds characterised for impurity species (Ne, Ar, Kr). Different flushing gases (D2, H2) and pathways to trigger a benign disruption were explored. The 55 kV NBH II generated a rich Alfvenic spectrum modulating the FI fas ion loss detector signal. NT configurations showed less toroidal Alfven excitation activity preferentially affecting higher FI pitch angles. Scrape-off layer and edge physics. gas puff imaging systems characterised turbulent plasma ejection for several advanced divertor configurations, including NT. Combined diagnostic array divertor state analysis in detachment conditions was compared to modelling revealing an importance for molecular processes. Divertor physics. Internal gas baffles diversified to include shorter/longer structures on the high and/or low field side to probe compressive efficiency. Divertor studies concentrated upon mitigating target power, facilitating detachment and increasing the radiated power fraction employing alternative divertor geometries, optimised X-point radiator regimes and long-legged configurations. Smaller-than-expected improvements with total flux expansion were better modelled when including parallel flows. Peak outer target heat flux reduction was achieved (>50%) for high flux-expansion geometries, maintaining core performance (H-98 > 1). A reduction in target heat loads and facilitated detachment access at lower core densities is reported. Real-time control. TCV's real-time control upgrades employed MIMO gas injector control of stable, robust, partial detachment and plasma beta feedback control avoiding neoclassical tearing modes with plasma confinement changes. Machine-learning enhancements include trajectory tracking disruption proximity and avoidance as well as a first-of-its-kind reinforcement learning-based controller for the plasma equilibrium trained entirely on a free-boundary simulator. Finally, a short description of TCV's immediate future plans will be given.

This paper discusses the development of a benign termination scenario for runaway electron (RE) beams on ASDEX Upgrade and TCV. A systematic study revealed that a low electron density (n e) companion plasma was required to achieve a large MHD instability, which expelled the confined REs over a large wetted area and allowed for the conversion of magnetic energy to radiation. Control of the companion plasma ne was achieved via neutral pressure regulation and was agnostic to material injection method. The neutral pressure required for recombination was found to be dependent on impurity species, quantity and RE current. On TCV, n e increased at neutral pressures above 1 Pa, indicating that higher collisionality between the REs and neutrals may lead to an upper pressure limit. The conversion of magnetic energy to radiated energy was measured on both machines and a decrease in efficiency was observed at high neutral pressure on TCV. The benign termination technique was able to prevent any significant increase in maximum heat flux on AUG from 200 to 600 kA of RE current, highlighting the ability of this approach to handle fully formed RE beams.

In 2021 JET exploited its unique capabilities to operate with T and D-T fuel with an ITER-like Be/W wall (JET-ILW). This second major JET D-T campaign (DTE2), after DTE1 in 1997, represented the culmination of a series of JET enhancements-new fusion diagnostics, new T injection capabilities, refurbishment of the T plant, increased auxiliary heating, in-vessel calibration of 14 MeV neutron yield monitors-as well as significant advances in plasma theory and modelling in the fusion community. DTE2 was complemented by a sequence of isotope physics campaigns encompassing operation in pure tritium at high T-NBI power. Carefully conducted for safe operation with tritium, the new T and D-T experiments used 1 kg of T (vs 100 g in DTE1), yielding the most fusion reactor relevant D-T plasmas to date and expanding our understanding of isotopes and D-T mixture physics. Furthermore, since the JET T and DTE2 campaigns occurred almost 25 years after the last major D-T tokamak experiment, it was also a strategic goal of the European fusion programme to refresh operational experience of a nuclear tokamak to prepare staff for ITER operation. The key physics results of the JET T and DTE2 experiments, carried out within the EUROfusion JET1 work package, are reported in this paper. Progress in the technological exploitation of JET D-T operations, development and validation of nuclear codes, neutronic tools and techniques for ITER operations carried out by EUROfusion (started within the Horizon 2020 Framework Programme and continuing under the Horizon Europe FP) are reported in (Litaudon et al Nucl. Fusion accepted), while JET experience on T and D-T operations is presented in (King et al Nucl. Fusion submitted).

Within the 9th European Framework programme, since 2021 EUROfusion is operating five tokamaks under the auspices of a single Task Force called ‘Tokamak Exploitation’. The goal is to benefit from the complementary capabilities of each machine in a coordinated way and help in developing a scientific output scalable to future largre machines. The programme of this Task Force ensures that ASDEX Upgrade, MAST-U, TCV, WEST and JET (since 2022) work together to achieve the objectives of Missions 1 and 2 of the EUROfusion Roadmap: i) demonstrate plasma scenarios that increase the success margin of ITER and satisfy the requirements of DEMO and, ii) demonstrate an integrated approach that can handle the large power leaving ITER and DEMO plasmas. The Tokamak Exploitation task force has therefore organized experiments on these two missions with the goal to strengthen the physics and operational basis for the ITER baseline scenario and for exploiting the recent plasma exhaust enhancements in all four devices (PEX: Plasma EXhaust) for exploring the solution for handling heat and particle exhaust in ITER and develop the conceptual solutions for DEMO. The ITER Baseline scenario has been developed in a similar way in ASDEX Upgrade, TCV and JET. Key risks for ITER such as disruptions and run-aways have been also investigated in TCV, ASDEX Upgrade and JET. Experiments have explored successfully different divertor configurations (standard, super-X, snowflakes) in MAST-U and TCV and studied tungsten melting in WEST and ASDEX Upgrade. The input from the smaller devices to JET has also been proven successful to set-up novel control schemes on disruption avoidance and detachment.

This work explains the anomalously high runaway electron (RE) pitch angles inferred in the flat-top of dedicated Tokamak à Configuration Variable (TCV) experiments. Kinetic modelling shows that the resonant interaction between the gyromotion of the electrons and the toroidal magnetic field ripple will give rise to strong pitch angle scattering in TCV. The resulting increase in synchrotron radiation power losses acts as a RE energy barrier. These observations are tested experimentally by a magnetic field ramp-down, which gradually reduces the resonant parallel momentum at which the REs interact with the ripple. Resulting changes in synchrotron emission geometry and intensity are observed using three multi-spectral camera imaging systems, viewing the RE beam at distinct spatial angles in multiple wavelength ranges. Experimental reconstructions of the RE distribution in momentum- and real-space are consistent with kinetic model predictions.

Runaway electrons (REs) are a concern for tokamak fusion reactors from discharge startup to termination. A sudden localized loss of a multi-megaampere RE beam can inflict severe damage to the first wall. Should a disruption occur, the existence of a RE seed may play a significant role in the formation of a RE beam and the magnitude of its current. The application of central electron cyclotron resonance heating (ECRH) in the Tokamak & agrave; Configuration Variable (TCV) reduces an existing RE seed population by up to three orders of magnitude within only a few hundred milliseconds. Applying ECRH before a disruption can also prevent the formation of a post-disruption RE beam in TCV where it would otherwise be expected. The RE expulsion rate and consequent RE current reduction are found to increase with applied ECRH power. Whereas central ECRH is effective in expelling REs, off-axis ECRH has a comparatively limited effect. A simple 0-D model for the evolution of the RE population is presented that explains how the effective ECRH-induced RE expulsion results from the combined effects of increased electron temperature and enhanced RE transport.

Experiments on ASDEX Upgrade (AUG) in 2021 and 2022 have addressed a number of critical issues for ITER and EU DEMO. A major objective of the AUG programme is to shed light on the underlying physics of confinement, stability, and plasma exhaust in order to allow reliable extrapolation of results obtained on present day machines to these reactor-grade devices. Concerning pedestal physics, the mitigation of edge localised modes (ELMs) using resonant magnetic perturbations (RMPs) was found to be consistent with a reduction of the linear peeling-ballooning stability threshold due to the helical deformation of the plasma. Conversely, ELM suppression by RMPs is ascribed to an increased pedestal transport that keeps the plasma away from this boundary. Candidates for this increased transport are locally enhanced turbulence and a locked magnetic island in the pedestal. The enhanced D-alpha (EDA) and quasi-continuous exhaust (QCE) regimes have been established as promising ELM-free scenarios. Here, the pressure gradient at the foot of the H-mode pedestal is reduced by a quasi-coherent mode, consistent with violation of the high-n ballooning mode stability limit there. This is suggestive that the EDA and QCE regimes have a common underlying physics origin. In the area of transport physics, full radius models for both L- and H-modes have been developed. These models predict energy confinement in AUG better than the commonly used global scaling laws, representing a large step towards the goal of predictive capability. A new momentum transport analysis framework has been developed that provides access to the intrinsic torque in the plasma core. In the field of exhaust, the X-Point Radiator (XPR), a cold and dense plasma region on closed flux surfaces close to the X-point, was described by an analytical model that provides an understanding of its formation as well as its stability, i.e., the conditions under which it transitions into a deleterious MARFE with the potential to result in a disruptive termination. With the XPR close to the divertor target, a new detached divertor concept, the compact radiative divertor, was developed. Here, the exhaust power is radiated before reaching the target, allowing close proximity of the X-point to the target. No limitations by the shallow field line angle due to the large flux expansion were observed, and sufficient compression of neutral density was demonstrated. With respect to the pumping of non-recycling impurities, the divertor enrichment was found to mainly depend on the ionisation energy of the impurity under consideration. In the area of MHD physics, analysis of the hot plasma core motion in sawtooth crashes showed good agreement with nonlinear 2-fluid simulations. This indicates that the fast reconnection observed in these events is adequately described including the pressure gradient and the electron inertia in the parallel Ohm’s law. Concerning disruption physics, a shattered pellet injection system was installed in collaboration with the ITER International Organisation. Thanks to the ability to vary the shard size distribution independently of the injection velocity, as well as its impurity admixture, it was possible to tailor the current quench rate, which is an important requirement for future large devices such as ITER. Progress was also made modelling the force reduction of VDEs induced by massive gas injection on AUG. The H-mode density limit was characterised in terms of safe operational space with a newly developed active feedback control method that allowed the stability boundary to be probed several times within a single discharge without inducing a disruptive termination. Regarding integrated operation scenarios, the role of density peaking in the confinement of the ITER baseline scenario (high plasma current) was clarified. The usual energy confinement scaling ITER98( p,y ) does not capture this effect, but the more recent H20 scaling does, highlighting again the importance of developing adequate physics based models. Advanced tokamak scenarios, aiming at large non-inductive current fraction due to non-standard profiles of the safety factor in combination with high normalised plasma pressure were studied with a focus on their access conditions. A method to guide the approach of the targeted safety factor profiles was developed, and the conditions for achieving good confinement were clarified. Based on this, two types of advanced scenarios (‘hybrid’ and ‘elevated’ q -profile) were established on AUG and characterised concerning their plasma performance.

The pre-thermal quench (pre-TQ) dynamics of a pure deuterium (D 2 ) shattered pellet injection (SPI) into a 3MA/7MJ JET H-mode plasma is studied via 3D non-linear MHD modelling with the JOREK code. The interpretative modelling captures the overall evolution of the measured density and radiated power. The simulations also identify the importance of the drifts of ablation plasmoids towards the tokamak low field side (LFS) and the impurities in the background plasma in fragment penetration, assimilation, radiative cooling and MHD activity in D 2 SPI experiments. It is found that plasmoid drifts lead to an about 70% reduction of the central line-integrated density (compared to a simulation without drifts) in the JET D 2 SPI discharge considered. Impurities that pre-exist before the SPI as well as those from possible impurity influxes related to the SPI are shown to dominate the radiation in the considered discharge. With inputs from JOREK simulations, modelling with the Lagrangian particle-based pellet code PELOTON reproduces the deviation of the SPI fragments in the direction of the major radius as observed by the fast camera. This confirms the role of rocket effects and plasmoid drifts in the considered discharge and reinforces the validity of the JOREK modelling. The limited core density rise due to plasmoid drifts and the strong radiative cooling and MHD activity with impurities (depending on their species and concentration) could limit the effectiveness of LFS D 2 SPI in runaway electron avoidance and are worth considering in the design of the ITER disruption mitigation system.

The impact of plasma shaping on the properties of high density H-mode scrape-off layer (SOL) profiles and transport at the outer midplane has been investigated on Tokamaka configuration variable. The experimental dataset has been acquired by evolving the upper triangularity while keeping the other parameters constant. The scan comprises delta up values between 0.0 and 0.6, excluding negative triangularity scenarios. Within this study, a transition from type-I edge localised modes to the quasi-continuous exhaust regime takes place from low to high delta up . The modification of the upstream SOL profiles has been assessed, in terms of separatrix quantities, within the alpha t turbulence control parameter theoretical framework (Eich et al 2020 Nucl. Fusion 60 056016). The target parallel heat load and the upstream near-SOL density profiles have been shown to broaden significantly for increasing alpha t . Correspondingly, in the far SOL a density shoulder formation is observed when moving from low to high delta up . These behaviours have been correlated with an enhancement of the SOL fluctuation level, as registered by wall-mounted Langmuir probes as well as the thermal helium beam diagnostic. Specifically, both the background and the filamentary-induced fluctuating parts of the first wall ion saturation current signal are larger at higher delta up , with filaments being ejected more frequently into the SOL. Comparison of two pulses at the extremes of the delta up scan range, but with otherwise same input parameters, shows that the midplane neutral pressure does not change much during the H-mode phase of the discharge. This indicates that indirect effects of the change in geometry, linked to first wall recycling sources, should not play a significant role. The total core radiation increases at high delta up , on account of a stronger plasma-wall interaction and resulting larger carbon impurity intake from the first wall. This is likely associated to the enhanced first wall fluctuations, as well as a smaller outer gap and the close-to-double-null magnetic topology at high shaping.

This work presents a system upgrade of the High Resolution Thomson Scattering (HRTS) diagnostic [Pasqualotto et al., Rev. Sci. Instrum. 75, 3891-3893 (2004)] on JET that allows it to measure low temperature (1-500 eV) plasma pre- and post-Thermal quench (TQ), which would help us further understand the Shattered Pellet Injection (SPI) physics. The upgrade was done by connecting optic fibers from the original HRTS system to four spectrometers specialized in measuring low temperature plasmas. The upgraded system allows for the measurement of low temperature plasma at up to 12 spatial points, which can be flexibly distributed throughout the JET outer midplane profile during the dedicated SPI experiments. In other JET experiments, four previously unused groups of fibers were used to measure the central plasma to provide disruption data without changing the standard HRTS system. The low temperature Thomson scattering system was installed, commissioned, and cross-calibrated against the standard HRTS diagnostic in a calibration pulse. The system worked reliably during the JET experiments and provided electron density and temperature profiles for pre- and post-TQ low temperature plasmas in the SPI campaign. (c) 2024 Author(s). All article content, except where otherwise noted, is licensed under a Creative Commons Attribution (CC BY) license(https://creativecommons.org/licenses/by/4.0/).

Precise values for radiated energy in tokamak disruption experiments are needed to validate disruption mitigation techniques for burning plasma tokamaks like ITER and SPARC. Control room analysis of radiated power (P rad) on JET assumes axisymmetry, since fitting 3D radiation structures with limited bolometry coverage is an under-determined problem. In mitigated disruptions, radiation is toroidally asymmetric and 3D, due to fast-growing 3D MHD modes and localized impurity sources. To address this problem, Emis3D adopts a physics motivated forward modeling ('guess and check') approach, comparing experimental bolometry data to synthetic data from user-defined radiation structures. Synthetic structures are observed with the Cherab modeling framework and a best fit chosen using a reduced chi 2 statistic. 2D tomographic inversion models are tested, as well as helical flux tubes and 3D MHD simulated structures from JOREK. Two nominally identical pure neon shattered pellet injection (SPI) mitigated discharges in JET are analyzed. 2D tomographic inversions with added toroidal freedom are the best fits in the thermal quench (TQ) and current quench (CQ). In the pre-TQ, 2D reconstructions are statistically the best fits, but are likely over-optimized and do not capture the 3D radiation structure seen in fast camera images. The next-best pre-TQ fits are helical structures that extend towards the high-field side, consistent with an impurity flow under the magnetic nozzle effect also observed in JOREK simulations. Whole-disruption radiated fractions of 0.98+0.03/ -0.29 and 1.01+0.02/-0.17 are found, suggesting that the stored energy may have been fully mitigated by each SPI, although mitigation efficiencies well below ITER and SPARC requirements for high energy pulses are still within the large uncertainties. Emis3D is also used to validate JOREK SPI simulations, and confirms improvements in matching experiment from changes to impurity modeling. Time-dependent toroidal peaking factors are calculated and discussed.

Massive material injections in the JET tokamak have been observed to substantially affect resistive bolometer measurements, resulting in a spurious radiated power signal proportional to the quantity injected and reaching up to 8 MW. These bolometers are calibrated and designed to operate in near vacuum but certain scenarios requiring large gas injections can push the neutral pressure past nominal values. This study demonstrates that the bolometry measurement can be affected at neutral pressures above 0.1 Pa following injections with standard gas valves, shattered pellet injections, and particularly massive gas injections. The power measurement of resistive bolometers is based on the temperature difference between a measurement sensor exposed to radiation and a shielded reference sensor. We employ a thermal conductivity model to demonstrate that the conduction through the gas and the distinct geometries between the sensors can affect their cooling efficiency. This additional cooling pathway, coupled with the Joule heating from the applied voltage causes the equilibrium temperatures of the sensors to diverge. Being the very basis of the measure, this temperature difference induces a signal that is erroneously interpreted as radiated power. Experiments show large discrepancies in the response to neutral pressure among bolometer channels, attributed to variations in channel physical parameters. Nonetheless, the modeled total radiated power reproduces the experimental measurements within an order of magnitude, affirming the sensitivity of resistive bolometers to neutral pressure and gas species.

A baffled snowflake minus low-field side (SF-LFS) is geometrically-optimised in tokamak a` configuration variable, increasing divertor neutral pressure, to evaluate the roles of divertor closure (comparing with an unbaffled SF-LFS) and magnetic geometry (comparing with a baffled single null (SN)) in power exhaust and core-divertor compatibility. Ohmically-heated L-mode discharges in deuterium, with a line-averaged core density of approximately 4.7 x 10(19 )m(-3), are seeded with nitrogen to approach detached conditions. Baffles in the SF-LFS configuration are found to reduce the peak outer target heat flux by up to 23%, without significantly affecting the location of the inter-null radiation region or the core-divertor compatibility. When compared to the baffled SN, the baffled SF-LFS exhibits a reduction in the outer target heat flux by up to 66% and the ability to balance the strike-point distribution of heat flux. These benefits are less significant with N-2 seeding, with similar peak target quantities (such as heat flux, electron temperature and ion flux) and divertor radiated power. Despite a radiating region located farther from the confined plasma for the SF-LFS than the baffled SN, no change in core confinement is observed. Core effective charge even indicates an increase in core impurity penetration for the SF-LFS. These experiments constitute a good reference for detailed model validations and extrapolations, exploring important physics such as core impurity shielding and the dependence of divertor cross-field transport on magnetic geometry.

The Shattered Pellet Injector (SPI) installed at ASDEX Upgrade (AUG) is one of the most flexible SPI systems currently in operation. It was specifically designed to provide input to the ITER disruption mitigation system [1]. The AUG SPI was so far used in approx. 240 plasma discharges to explore SPI efficacy in disruption mitigation, to optimize material assimilation, reduce heat loads and radiation asymmetries, and to generate a diverse dataset for model validation. Our results indicate that rectangular shatter heads with relatively shallow mitre bends lead to more reproducible

Future fusion reactors require a safe, steady-state divertor operation. With deep divertor detachment, which is typically induced by impurity seeding, the radiation concentrates in a small region at the X-point or on closed flux surfaces above the X-point. This so-called X-point radiator (XPR) moves further inside the confined region with increasing seeding and the location can be actively controlled.At AUG, the parameter space for operation with an XPR was significantly extended, using active feedback on the XPR location. The XPR is observed in nearly the whole operational space of AUG in the high-densities or high collisionality regime. ELM suppression is consistently observed in all cases where the XPR was moved to a significant height above the X-point.Direct measurements of density and temperature from the region around the XPR using the new divertor Thomson scattering system at AUG indicate that the temperature at the location of the XPR remains high (>30eV) and only the region towards the X-point cools down further. In this cold XPR core, the temperature reduces to about 1eV.An XPR is also observed in TCV by the injection of nitrogen as extrinsic impurity. This highlights that the wall material (W for AUG, C for TCV) or machine size does not play a significant role for the existence of the regime. However, the scenario appears to be less stable in TCV. First experiments show the necessity of an active control for the XPR: Depending on the wall conditions and the nitrogen wall storage, the required nitrogen seeding level to achieve an XPR changes.Both, the low temperatures measured radially outside of the radiation zone at AUG, and the lower stability of the XPR regime at TCV with the presence of carbon are consistent with the predictions of a one-dimensional model of the XPR. However, the model would predict the development of the cold XPR core, and significant radiation at the X-point might already exist before reaching this cold temperature solution.

Nonlinear 3D MHD simulations of shattered-pellet injection (SPI) in JET show prototypical SPI-driven disruptions using the M3D-C1 and NIMROD extended-MHD codes. Initially, radiation-driven thermal quenches are accelerated by MHD activity as the pellet crosses rational surfaces, leading to a radiation spike, global stochasticization of the magnetic field, and a complete thermal quench. Eventually, current quenches, preceded by a current spike are seen as the Ohmic heating becomes equal to the radiative cooling. The results are qualitatively similar for both a single monolithic pellet, pencil-beam model, and a realistic shatter to represent the SPI plume. A scan in viscosity from 500 to 2000 m 2 s −1 for MHD simulations finds that reducing viscosity increases MHD activity and decreases thermal quench time slightly. A realistic cloud of fragments modeling shows that mixed-D–Ne pellet travels deeper into the plasma core before the thermal quench. At the slow pellet speeds, the pellet is found to be moving slowly enough inward that even the 5% neon in the mixed pellet is enough to effectively radiate the thermal energy available. Radiation toroidal peaking is predicted to be at levels consistent with experimental observations and reduced as the pellet travels deeper into the plasma. These simulations lay the ground work for more-sophisticated validative and predictive modeling of SPI in JET using both M3D-C1 and NIMROD.

The TCV tokamak continues to leverage its unique shaping capabilities, flexible heating systems and modern control system to provide a stepladder approach for extrapolations of experimental results from different ma-chines to ITER and DEMO. TCV's configurational flexibility has recently been enhanced by the installation of two heating neutral beams, new dual frequency gyrotrons, removable divertor gas baffles together with upgrades of its diagnostic infrastructure.Plasma regimes with high plasma pressure, a wider range of temperature ratios and significant fast-ion population are now attainable on TCV. A 1.3 MW/28 keV heating beam (NBI-1) has been operated on TCV from 2015 introducing the direct ion auxiliary heating. A second 1MW/50-60 keV high-energy neutral beam (NBI-2) has since been procured, manufactured and installed on TCV in July 2021. NBI-2 injected near anti-co -linearly to NBI-1 is designed to probe plasma physics issues of higher plasma density, fast ion plasma interactions with static and dynamic fields and plasma rotation. The higher NBI-2 energy greatly enhances the operational space for fast ion studies. NBI-2 commissioning is presently ongoing in parallel with TCV experiments using both NBIs.This paper summarises the experience with intensive use and improvements of the NBI-1, together with the status of NBI-2 commissioning.