The Electron Ion Collider (EIC) Hadron Storage Ring (HSR) will reuse many of the existing superconducting (SC) magnets of the RHIC storage rings. To comply with the beamline vacuum requirements in more demanding operational scenarios, the beampipe of the RHIC SC magnets will be equipped with low surface impedance, low secondary electron yield (SEY) beam screens. The installation of these beam screens will be done with the SC magnets as installed today, thus making it a critical operation for a timely EIC installation. The beam screen inner dimensions must be maximized to retain enough aperture to the beam. On the other hand, keeping enough clearance between the screen and the beampipe is critical to ensure a smooth beam screen installation. A survey probe was designed and built to measure the inner diameter of several RHIC SC magnets in-situ and provide critical data for the beam screen design optimization. This paper reports on the design of the probe and the results from the survey campaign.

The Electron Ion Collider (EIC) Hadron Storage Ring (HSR) will reuse most of the existing superconducting magnets from the RHIC storage ring. However, the existing stripline beam position monitors (BPM) used for RHIC will not be compatible with the planned EIC hadron beam parameters that include higher intensity, shorter bunches, and some operational scenarios with large radial offsets of the beam in the vacuum chamber. To address these challenges, the existing RHIC stripline BPMs will be decommissioned, and a new BPM design using button pick-ups integrated in a new vacuum interconnect/bellows assembly will be installed adjacent to the decommissioned BPMs. A dedicated analysis of the new BPM housing and button pick-up design has been conducted to assess the thermal effects caused by heat conduction, beam induced resistive wall heating and the RF heating from the BPM signal propagation through the cryogenic cables. This paper reports on the thermal design and analysis results to quantify the heat transfer and temperature distribution that can be expected on the new HSR cryogenic BPM.

The Open Access book discusses spin in accelerator combining aspects of physics, computational science, electrical and mechanical engineering.

The Electron-Ion Collider (EIC) presently under construction at Brookhaven National Laboratory will collide polarized high energy electron beams with hadron beams with design luminosities up to 1 × 10 34 cm −2 s −1 in center mass energy range of 20-140 GeV. We studied the planned electron-proton collisions using a Particle-In-Cell (PIC) based Poisson solver in strong-strong beam-beam simulation. We observed a much larger proton emittance growth rate than in weak-strong simulation. To understand the numerical noise and its impact on strong-strong simulation results, we carried out extensive studies to identify all possible causes for artificial emittance growth and quantify their contributions. In this article, we summarize our study activities and findings. This work will help us better understand the simulated emittance growth and the limits of the PIC based strong-strong beam-beam simulation.

The Electron-Ion Collider (EIC) will collide electrons with hadrons at center-of-mass energies up to 140 GeV (in the case of electron-proton collisions). A 3.8-kilometer electron storage ring is being designed, which will store electrons with a range of energies up to 18 GeV for collisions at one or two interaction points. At energies up to 10 GeV the arcs will be tuned to provide 60 degree phase advance per cell in both planes, whereas at top energy of 18 GeV a 90 degree phase advance per cell will be used, which largely compensates for the horizontal emittance increase with energy. The optics must be matched at three separate energies, and the different phase-advance requirements in both the arc cells and the straight sections make this challenging. Moreover, the spin rotators must fulfill requirements for polarization and spin matching at widely different energies while satisfying technical constraints. In this paper these challenges and proposed solutions are presented and discussed.

the magnet axis. The exit window of the tube was 160 mm from the surface of the sample located in a quartz diameter with 11.5 mm diameter in the center of the probe of a Varian E-3 ESR spectrometer. The cell was covered with a cup-like teflon stopper to keep atmospheric oxygen from the sample. The stopper contacted the sample surface. The x-ray radiation hit the sample after passing through a 0.5-mm-thick Teflon layer. The irradiated sample surface was 0.5 cm/sup 2/ in area. A quartz light conductor 9 mm in diameter and 0.5 m in length was attached to the lower edge of the cell. This device was used to conduct light from the sample to an FEU-130 photomultiplier in a Permalloy screen. The signal was transferred from the photomultiplier anode to the inlet of the synchronous detection block of the E-3 ESR spectrometer.

The possibility of two interaction regions (IRs) is a design requirement for the Electron Ion Collider (the EIC). There is also a significant interest from the nuclear physics community in a 2nd IR with measurements capabilities complementary to those of the first IR. While the 2nd IR will be in operation over the entire energy range of ~20GeV to ~140GeV center of mass (CM). The 2nd IR can also provide an acceptance coverage complementary to that of the first. We present a brief overview and the current progress of the 2nd IR design in terms of the parameters, magnet layout, and beam dynamics.

The operation of RHIC collider rings in polarized proton runs includes helical snakes, which allow for preserving polarization during acceleration to store energies. The RHIC lattice also includes spin rotators, operated when nonvertical polarization or corrections to the orientation of polarization at the interaction points are required. Utilization of OPERA field maps of snakes and rotators has been systematized in the past decade, in order to assess in detail the effects of these spin devices on beam polarization, and their perturbative effects on beam optics. The method is also used in ongoing studies regarding the future Electron Ion Collider, to permit increasing average store polarization to at least 70% at 275 GeV and the acceleration of polarized helion with low polarization losses. This paper reviews various applications and outcomes of these field map methods. It is thereby also a review of studies undertaken as part of beam polarization research activities at RHIC in recent years.

Polarization lifetime for He3 using two and six snakes are studied using the T-BMT Spin Resonance Tracker code. This code integrates a reduced spinor form of the T-BMT equation including only several spin resonances and the kinematics of synchrotron motion. It was previously benchmarked against RHIC polarization lifetime under the two snake system.

A new layout and optics for the Electron Storage Ring (ESR) have been produced with revised spin rotators in IRs 6 and 8, a redesign of IR10, and a new geometric layout for the ring. In this report, the efforts to produce this lattice are documented, including the motivation for design decisions. This new lattice, version 5.5, will be used as the baseline for future studies.