Originally founded as a trade school in 1925 and incorporated in 1969, KUAS was refounded in 2019 under the leadership of Shigenobu Nagamori. Its two campuses are located in Ukyō-ku, Kyoto City, and Kameoka City, Kyoto Prefecture.The university is organized into five faculties and five graduate schools. The undergraduate faculties include the Faculty of Economics and Business Administration, the Faculty of Humanities, the Faculty of Bioenvironmental Science, the Faculty of Health and Medical Sciences, and the Faculty of Engineering. The graduate schools include the Graduate School of Economics, the Graduate School of Business Administration, the Graduate School of Human Culture, the Graduate School of Bioenvironmental Science, and the Graduate School of Engineering.In 2020, the university's Faculty of Engineering began to offer programs taught entirely in English, signaling a shift towards internationalization and English-medium education.
Kinetics of tagatose formation from galactose in arginine solution at various temperatures and the effect of ethanol concentration on tagatose yield were investigated. A solution containing 5
Effective wetland management requires reliable indicator species and monitoring methods that minimize ecosystem disturbance. This study presents a non-invasive UAV-based approach for monitoring the distribution and habitat associations of Nannophya pygmaea, a wetland indicator dragonfly, in a protected floating-mat wetland in Japan. High-resolution aerial imagery enabled direct detection of individuals across the entire wetland, while multispectral and thermal data were used to characterize vegetation structure and surface temperature. Across eight surveys conducted during a single emergence season, 558 adult individuals were identified, allowing quantification of within-season dynamics and sex-specific spatial distribution. Logistic regression analyses revealed clear associations between occurrence probability and UAV-derived environmental variables, with surface temperature exerting the strongest influence. Vegetation structure and thermal conditions jointly explained fine-scale habitat differentiation between males and females. The approach allows repeated monitoring without entering fragile wetland habitats and provides spatially explicit information relevant to habitat condition assessment. Logistic regression models were used to quantify relationships between occurrence and environmental variables. However, the absence of ground-truth validation and the potential for re-sighting of individuals should be considered when interpreting the results. Logistic regression models were used to quantify relationships between occurrence and environmental variables. However, the absence of ground-truth validation and the potential for re-sighting of individuals should be considered when interpreting the results. These findings demonstrate that UAV-based monitoring of indicator species can support adaptive wetland management by linking species responses to microhabitat structure and environmental change.
Daw et al. (Sustain Sci, 2026) provide a valuable overview of how deliberative mini-publics (DMPs) could bridge sustainability science, public understanding, and policy. Their framework identifies three important mechanisms through which DMPs can contribute to sustainability transformations. This comment builds on their analysis by identifying a critical temporal gap: while DMPs can increase participants’ awareness of future generations, current evidence suggests they may not sufficiently shift participants’ willingness to accept trade-offs for the future. I introduce Future Design (FD), an approach that activates ‘futurability’—the human capacity to prioritise future generations’ well-being over immediate gains—and present experimental and practical evidence of its effects. Rather than proposing FD as an alternative to DMPs, I suggest that integrating FD mechanisms within DMP processes could strengthen the temporal depth of citizen deliberation, and invite collaborative experimentation to test this proposition.
Herein, we performed comprehensive molecular dynamics (MD) simulations, including long-term submicrosecond calculations, to analyze the interaction between hydrogen atoms and an {112}< 111> edge dislocation in alpha-iron. We confirmed three interactions: (1) dragging, (2) cycle of pinning and depinning (pinning/depinning), and (3) twinning initiation. Dragging was typically observed at low dislocation speeds (<= 0.1 m/s) and high temperatures. The drag stress was proportional to trapped-hydrogen concentration (CH) and dislocation speed and sharply decreased with increasing temperature. Twinning was caused by the strong pinning effect on the involved dislocation by hydrogen atoms and was typically observed at low temperatures and high CH values. Under intermediate conditions, pinning/depinning was observed. Based on atomistic mechanisms revealed via MD simulations, we developed theoretical models for these interactions and verified their predictability. We also clarified that dragging and partial/temporal depinning occurred simultaneously at wide ranges of strain rates and temperatures. Subsequently, we predicted the shear stress-dislocation speed relation for long dislocation lines and the boundaries of dragging-dominant, depinning-dominant, and twining regions at realistic strain rates; these predictions were beyond the spatiotemporal reach of direct atomistic simulations. We also clarified the origins of the experimentally measured large activation volume for dragging as well as the modification of stress-strain curves and deformation behavior by hydrogen atoms. Finally, we proposed mechanisms that accounted for the coexistence of high flow stress and localized plasticity. The developed theoretical models and identified mechanisms can be applied to solute-dislocation interactions across various slip systems, material-solute combinations, and crystallographic structures.
Three-dimensional (3D) printing, or additive manufacturing, has transformed materials fabrication by enabling precise, layer-by-layer construction of complex structures, overcoming traditional limitations. This innovation offers scalability and customization for advanced energy storage devices (ESDs). Simultaneously, metal-organic frameworks (MOFs), with their high porosity, tunable chemistry, and large surface area, have shown great promise for ESDs but suffer from inherent fragility, limiting their industrial applications. In this context, 3D printing provides a sustainable solution by creating robust MOF-based monoliths, expanding their applications in energy storage and conversion systems. This review explores the synergy between 3D printing and MOFs, highlighting their potential to revolutionize sustainable energy storage technologies. We provide a comprehensive analysis of 3D printing’s impact on material science, the distinct characteristics of MOFs, and their integration into ESDs. Advancements in 3D printing techniques, MOF-based ink formulations, and their incorporation into functional devices are critically examined. Case studies and critical evaluations address current limitations, emerging trends, and future research directions in this rapidly evolving field. Finally, we emphasize the transformative potential of 3D-printed MOFs in advancing energy storage technologies and their significance for future innovation in materials science and sustainable energy solutions.