
In order to solve the problem of frequent disconnection of carbon fiber conductors for large-capacity and long-distance transmission due to undetectable hidden defects,a detection method for hidden defects in multi-strand carbon fiber composite core conductors based on optical fiber sensing technology was proposed.The operating environment of the wire was established and the operating conditions were simulated.The time-domain reflection technology based on distributed fiber Brillouin scattering was adopted to detect the temperature and strain distribution of carbon fiber wires,and the optical time-domain reflection technology was combined to detect the loss of optical fibers in carbon fiber wires.Comprehensive comparative analysis was conducted to obtain signal feature quantities such as fiber temperature,strain and loss that could characterize hidden defects in multi-strand carbon fibers,and a neural network model was constructed with each signal feature quantity as input to the model.Through model training,the various weight coefficients within the model were determined,enabling it to effectively detect hidden defects in multi-strand carbon fiber composite core wires.The experimental results show that this method can effectively obtain signal feature quantities of various types of fiber optic and can accurately detect various hidden defects in wires,which has important practical application values.
Based on the phase delay estimation of narrowband signals, a signal localization method is proposed in this paper by using a non-uniform linear array, which solves the phase wrapping problem caused by the increase of array element spacing and improves the accuracy of localization. This paper proposes an estimation algorithm for correcting the amount of wrapping and calculating the time delay in the case of nonuniform linear array approach, and gives the conditions that need to be satisfied for non-uniform array element spacing. The signal localization method improves the available array aperture for positioning and greatly reduces the number of array elements required for the same aperture compared to a general uniform linear array, thus reducing the need for subsequent signal processing equipment. A localization system is also constructed and tested. The experiments show that the method effectively improves the accuracy of localization of narrowband sound sources in open space.
Short-circuit faults occurring on overhead lines in the DC distribution network can be divided into permanent short-circuit faults and transient short-circuit faults. When dealing with short-circuit faults, the existing hybrid DC circuit breaker must first cut off the fault current and then reclose, which will cause a brief power interruption. In this regard. This paper proposes a hybrid DC circuit breaker topology with selective interruption, which is suitable for medium voltage DC situations. The circuit breaker can choose operation mode according to different fault types. The circuit breaker can be operated according to different fault types: permanent short-circuit faults can be eliminated within 9 ms; when dealing with transient faults, it allows the system to resume normal operation without interrupting the current and releases the energy generated during the fault. In addition, the working process analysis and theoretical derivation of the proposed topology are carried out in this paper, and the simulation verification is carried out in the single-ended DC equivalent system. The simulation results verify the feasibility of the topology.
为解决传统几何测量方法中人工手动计算费时费力和效率低下等问题,设计了一套针对介质阻挡放电(DBD)型臭氧发生器电气参数的实时在线测量系统,大大提高了DBD型臭氧发生器电气参数测量的准确性和快速性.首先,从控制器单元回路、信号检测回路等硬件电路系统、数据处理单元和结果输出等软件系统出发,详细分析了实时在线测量系统的设计思想.其次,通过搭建实时在线测量系统实验平台,实时采集了DBD型臭氧发生器负载端在不同时刻的电压、电流值的关键点,快速而准确地在线实时计算出DBD型臭氧发生器的介质阻挡电容值、气隙电容值和放电功率值.然后,研究了外加电压幅值和频率变化对介质阻挡放电参数的影响,数据表明,增大外加电压幅值和工作频率,电荷的传输能力增强,放电管的介质等效电容变大,放电间隙等效电容减小,最终趋于稳定.最后,对本文所提出的在线测量系统进行了简要的总结.
数字基带移相电路是数字波束赋形电路的重要组成部分.分析了数字波束赋形电路中基带信号的相位控制方法,基于FPGA平台设计了一种数字基带移相电路,该电路通过AHB接口获取相位控制字,根据相位控制字的大小调节FIFO存储器中信号的缓存时间来达到相位调节的目的.AHB接口的高速能力使得移相参数的调节具有实时性,结合FPGA并行运算的优势,可以同时对多通道数字基带信号进行相位调节.在集成设计环境Vivado平台上使用Verilog语言对移相电路进行设计,通过在线逻辑分析仪测试验证了设计的可行性.