On December 5, 2022, an indirect drive fusion implosion on the National Ignition Facility (NIF) achieved a target gain G_{target} of 1.5. This is the first laboratory demonstration of exceeding "scientific breakeven" (or G_{target}>1) where 2.05 MJ of 351 nm laser light produced 3.1 MJ of total fusion yield, a result which significantly exceeds the Lawson criterion for fusion ignition as reported in a previous NIF implosion [H. Abu-Shawareb et al. (Indirect Drive ICF Collaboration), Phys. Rev. Lett. 129, 075001 (2022)PRLTAO0031-900710.1103/PhysRevLett.129.075001]. This achievement is the culmination of more than five decades of research and gives proof that laboratory fusion, based on fundamental physics principles, is possible. This Letter reports on the target, laser, design, and experimental advancements that led to this result.

For more than half a century, researchers around the world have been engaged in attempts to achieve fusion ignition as a proof of principle of various fusion concepts. As recently reported, a burning plasma state, where the alpha-heating in the plasma is the primary source of heating, was achieved in laboratory experiments. Following the Lawson criterion, an ignited plasma is one where the fusion heating power is high enough to overcome all the physical processes that cool the fusion plasma, creating a positive thermodynamic feedback loop with rapidly increasing temperature. In inertially confined fusion, ignition is a state where the fusion plasma can begin ``burn propagation'' into surrounding cold fuel, enabling the possibility of high energy gain. While ``scientific breakeven'' (i.e. unity target gain) has not yet been achieved, this talk reports the first controlled fusion experiment on the National Ignition Facility to produce capsule gain greater than unity (here 5.8) and reach ignition by many different formulations of the Lawson criterion. In the talk, we will discuss some key basic physics inertial confinement fusion (ICF) principles behind the burning plasma and ignition results as well as discuss future challenges.

We have demonstrated the world's highest average power, fully diode-pumped, petawatt-class peak power laser, the High-repetition-rate Advanced Petawatt Laser System (HAPLS) [1-3]. These first commissioning results at 16J (stretched) at 3%Hz fully validate projected performance of 30J/30fs (>1PW) at 10Hz. The laser has been operated at this intermediate level at Lawrence Livermore National Laboratory to demonstrate integrated performance of all subsystems and provide benchmarking data to laser performance models before further increasing energy and peak power. Data was obtained during multiple campaigns, exceeding several hours of run time, and a snapshot of 60min of data is shown in Fig. 1. The average pump laser 1ω (1053nm) energy was 97J with an rms stability of 0.7%, 2ω (527nm) energy at the Ti:sapphire power amplifier was 62J, and the average stretched short pulse energy was 16J. A full-aperture diagnostic suite allows simultaneous, single-shot measurement of energy, spectrum, beam quality, and pulse duration at full repetition rate. Single-shot SPIDER retrieved pulse shapes (Fig. 1 inset) with an average pulse duration over 12000 consecutive shots of 28.6fs (rms=1.4fs). The mean pulse duration is consistent with the measured spectral bandwidth and is ∼1.2× the transform limit. All results shown are raw data without filtering or averaging, demonstrating the exceptional pulse characteristics, repeatability, and stability of the entire laser system.

Overview of progress in construction and testing of the laser systems of ELI-Beamlines, accomplished since 2015, is presented. Good progress has been achieved in construction of all four lasers based largely on the technology of diode-pumped solid state lasers (DPSSL). The first part of the L1 laser, designed to provide 200 mJ < 15 fs pulses at 1 kHz repetition rate, is up and running. The L2 is a development line employing a 10 J / 10 Hz cryogenic gas-cooled pump laser which has recently been equipped with an advanced cryogenic engine. Operation of the L3-HAPLS system, using a gas-cooled DPSSL pump laser and a Ti: sapphire broadband amplifier, was recently demonstrated at 16 J / 28 fs, at 3.33 Hz rep rate. Finally, the 5 Hz OPCPA front end of the L4 kJ laser is up running and amplification in the Nd:glass large-aperture power amplifiers was demonstrated.

This talk will provide an overview of high power laser research at Lawrence Livermore National Laboratory (LLNL). It will discuss the status of the National Ignition Facility (NIF) laser. In addition, the talk will describe other laser development activities such as the development of high average power lasers and novel fiber lasers. The National Ignition Facility (NIF) has been in service since 2007 and operating with > 1 MJ energies since 2009. During this time the facility has transitioned to become an international user facility and increased the shot rate from similar to 150 target shots per year to greater than 400 shots per year. Today, the NIF plays an essential role in the US Stockpile Stewardship Program, providing data under the extreme conditions needed to validate computer models and train the next generation of stockpile stewards. Recent upgrades include the Advanced Radiographic Capability (ARC), a high energy short pulse laser used to do high resolution radiography. In addition to the NIF, this talk will include an overview of progress on the high average power laser development, recent results from fiber laser development activities and improvements to laser design and computational capabilities.

Large laser systems that deliver optical pulses with peak powers exceeding one Petawatt (PW) have been constructed at dozens of research facilities worldwide and have fostered research in High-Energy-Density (HED) Science, High-Field and nonlinear physics [1]. Furthermore, the high intensities exceeding 1018W/cm2 allow for efficiently driving secondary sources that inherit some of the properties of the laser pulse, e.g. pulse duration, spatial and/or divergence characteristics. In the intervening decades since that first PW laser, single-shot proof-of-principle experiments have been successful in demonstrating new high-intensity laser-matter interactions and subsequent secondary particle and photon sources. These secondary sources include generation and acceleration of charged-particle (electron, proton, ion) and neutron beams, and x-ray and gamma-ray sources, generation of radioisotopes for positron emission tomography (PET), targeted cancer therapy, medical imaging, and the transmutation of radioactive waste [2, 3]. Each of these promising applications requires lasers with peak power of hundreds of terawatt (TW) to petawatt (PW) and with average power of tens to hundreds of kW to achieve the required secondary source flux.

The HAPLS laser system has been commissioned to its first integrated performance milestone, delivering laser pulses with 16J sub-30fs duration at a 3⅓Hz repetition rate. This first all-diode-pumped petawatt-class laser offers the average powers required for secondary source applications.

Phase 1 performance ramping of the HAPLS pump laser, a high-energy DPSSL based on Nd:glass, successfully produced 70J at 1053nm from a single aperture and 39J at 527nm using LBO frequency converter running at 3.3Hz repetition rate.

Initial performance ramping of the HAPLS pump laser, a high-energy DPSSL based on Nd:glass, produced 70J at 1053nm from a single aperture and 39J at 527nm using LBO frequency converter all at 3.3Hz repetition rate.

The possibility of imploding small capsules to produce mini-fusion explosions was explored soon after the first thermonuclear explosions in the early 1950s. Various technologies have been pursued to achieve the focused power and energy required for laboratory-scale fusion. Each technology has its own challenges. For example, electron and ion beams can deliver the large amounts of energy but must contend with Coulomb repulsion forces that make focusing these beams a daunting challenge. The demonstration of the first laser in 1960 provided a new option. Energy from laser beams can be focused and deposited within a small volume; the challenge became whether a practical laser system can be constructed that delivers the power and energy required while meeting all other demands for achieving a high-density, symmetric implosion. The National Ignition Facility (NIF) is the laser designed and built to meet the challenges for study of high-energy-density physics and inertial confinement fusion (ICF) implosions. This paper describes the architecture, systems, and subsystems of NIF. It describes how they partner with each other to meet these new, complex demands and describes how laser science and technology were woven together to bring NIF into reality.

BackgroundThere is currently conflicting evidence surrounding the effects of obesity on postoperative outcomes. Previous studies have found obesity to be associated with adverse events, but others have found no association. The aim of this study was to determine whether increasing body mass index (BMI) is an independent risk factor for development of major postoperative complications.MethodsThis was a multicentre prospective cohort study across the UK and Republic of Ireland. Consecutive patients undergoing elective or emergency gastrointestinal surgery over a 4-month interval (October-December 2014) were eligible for inclusion. The primary outcome was the 30-day major complication rate (Clavien-Dindo grade III-V). BMI was grouped according to the World Health Organization classification. Multilevel logistic regression models were used to adjust for patient, operative and hospital-level effects, creating odds ratios (ORs) and 95 per cent confidence intervals (c.i.).ResultsOf 7965 patients, 2545 (320 per cent) were of normal weight, 2673 (336 per cent) were overweight and 2747 (345 per cent) were obese. Overall, 4925 (618 per cent) underwent elective and 3038 (381 per cent) emergency operations. The 30-day major complication rate was 114 per cent (908 of 7965). In adjusted models, a significant interaction was found between BMI and diagnosis, with an association seen between BMI and major complications for patients with malignancy (overweight: OR 159, 95 per cent c.i. 112 to 229, P = 0008; obese: OR 191, 131 to 283, P = 0002; compared with normal weight) but not benign disease (overweight: OR 089, 071 to 112, P = 0329; obese: OR 084, 066 to 106, P = 0147).ConclusionOverweight and obese patients undergoing surgery for gastrointestinal malignancy are at increased risk of major postoperative complications compared with those of normal weight.

Corrective optical elements form an important part of high-precision optical systems. We have developed a method to manufacture high-gradient corrective optical elements for high-power laser systems using deterministic magnetorheological finishing (MRF) imprinting technology. Several process factors need to be considered for polishing ultraprecise topographical structures onto optical surfaces using MRF. They include proper selection of MRF removal function and wheel sizes, detailed MRF tool and interferometry alignment, and optimized MRF polishing schedules. Dependable interferometry also is a key factor in high-gradient component manufacture. A wavefront attenuating cell, which enables reliable measurement of gradients beyond what is attainable using conventional interferometry, is discussed. The results of MRF imprinting a 23 μm deep structure containing gradients over 1.6 μm / mm onto a fused-silica window are presented as an example of the technique's capabilities. This high-gradient element serves as a thermal correction plate in the high-repetition-rate advanced petawatt laser system currently being built at Lawrence Livermore National Laboratory.

Laser-induced damage threshold (LIDT) testing was performed on commercially-available multilayer dielectric coatings to qualify for use in the High Repetition-Rate Advanced Petawatt Laser System (HAPLS) for Extreme Light Infrastructure Beamlines. Various tests were performed with uncompressed pulses (150 ps) from a 780 nm-centered Ti:Sapphire regenerative ampliflier, and the raster scan method was used to determine the best-performing coatings. Performance varied from 2–8 J/cm2 across samples from 6 different manufacturers.

Network packet inspection using port mirroring provides the ultimate tool for understanding complex behaviors in large distributed control systems. The timestamped captures of network packets embody the full spectrum of protocol layers and uncover intricate and surprising interactions. No other tool is capable of penetrating through the layers of software and hardware abstractions to allow the researcher to analyze an integrated system composed of various operating systems, closed-source embedded controllers, software libraries and middleware. Being completely passive, the packet inspection does not modify the timings or behaviors. The completeness and fine resolution of the network captures present an analysis challenge, due to huge data volumes and difficulty of determining what constitutes the signal and noise in each situation. We discuss the development of a deep packet inspection toolchain and application of the R language for data mining and visualization. We present case studies demonstrating off-normal analysis in a distributed real-time control system. In each case, the toolkit pinpointed the problem root cause which had escaped traditional software debugging techniques.

The Advanced Radiographic Capability (ARC) currently under development for the National Ignition Facility (NIF) will provide short (1-50 picoseconds) ultra high power (>1 Petawatt) laser pulses used for a variety of diagnostic purposes on NIF ranging from a high energy xray pulse source for backlighter imaging to an experimental platform for fast-ignition. A single NIF Quad (4 beams) is being upgraded to support experimentally driven, autonomous operations using either ARC or existing NIF pulses. Using its own seed oscillator, ARC generates short, wide bandwidth pulses that propagate down the existing NIF beamlines for amplification before being redirected through large aperture gratings that perform chirped pulse compression, generating a series of high-intensity pulses within the target chamber. This significant effort to integrate the ARC adds 70% additional control points to the existing NIF Quad and will be deployed in several phases over the coming year. This talk discusses some new unique ARC software controls used for short pulse operation on NIF and integration techniques being used to expedite deployment of this new diagnostic.

First results from the analysis of neutron image data collected on implosions of cryogenically layered deuterium-tritium capsules during the 2011-2012 National Ignition Campaign are reported. The data span a variety of experimental designs aimed at increasing the stagnation pressure of the central hotspot and areal density of the surrounding fuel assembly. Images of neutrons produced by deuterium–tritium fusion reactions in the hotspot are presented, as well as images of neutrons that scatter in the surrounding dense fuel assembly. The image data are compared with 1D and 2D model predictions, and consistency checked using other diagnostic data. The results indicate that the size of the fusing hotspot is consistent with the model predictions, as well as other imaging data, while the overall size of the fuel assembly, inferred from the scattered neutron images, is systematically smaller than models' prediction. Preliminary studies indicate these differences are consistent with a significant fraction (20%–25%) of the initial deuterium-tritium fuel mass outside the compact fuel assembly, due either to low mode mass asymmetry or high mode 3D mix effects at the ablator-ice interface.

The National Ignition Facility has been used to compress deuterium-tritium to an average areal density of ~1.0±0.1 g cm(-2), which is 67% of the ignition requirement. These conditions were obtained using 192 laser beams with total energy of 1-1.6 MJ and peak power up to 420 TW to create a hohlraum drive with a shaped power profile, peaking at a soft x-ray radiation temperature of 275-300 eV. This pulse delivered a series of shocks that compressed a capsule containing cryogenic deuterium-tritium to a radius of 25-35 μm. Neutron images of the implosion were used to estimate a fuel density of 500-800 g cm(-3).

The first inertial confinement fusion implosion experiments with equimolar deuterium-tritium thermonuclear fuel have been performed on the National Ignition Facility. These experiments use 0.17 mg of fuel with the potential for ignition and significant fusion yield conditions. The thermonuclear fuel has been fielded as a cryogenic layer on the inside of a spherical plastic capsule that is mounted in the center of a cylindrical gold hohlraum. Heating the hohlraum with 192 laser beams for a total laser energy of 1.6 MJ produces a soft x-ray field with 300 eV temperature. The ablation pressure produced by the radiation field compresses the initially 2.2-mm diameter capsule by a factor of 30 to a spherical dense fuel shell that surrounds a central hot-spot plasma of 50 μm diameter. While an extensive set of x-ray and neutron diagnostics has been applied to characterize hot spot formation from the x-ray emission and 14.1 MeV deuterium-tritium primary fusion neutrons, thermonuclear fuel assembly is studied by measuring the down-scattered neutrons with energies in the range of 10 to 12 MeV. X-ray and neutron imaging of the compressed core and fuel indicate a fuel thickness of (14 ± 3) μm, which combined with magnetic recoil spectrometer measurements of the fuel areal density of (1 ± 0.09) g cm–2 result in fuel densities approaching 600 g cm–3. The fuel surrounds a hot-spot plasma with average ion temperatures of (3.5 ± 0.1) keV that is measured with neutron time of flight spectra. The hot-spot plasma produces a total fusion neutron yield of 1015 that is measured with the magnetic recoil spectrometer and nuclear activation diagnostics that indicate a 14.1 MeV yield of (7.5±0.1)×1014 which is 70% to 75% of the total fusion yield due to the high areal density. Gamma ray measurements provide the duration of nuclear activity of (170 ± 30) ps. These indirect-drive implosions result in the highest areal densities and neutron yields achieved on laser facilities to date. This achievement is the result of the first hohlraum and capsule tuning experiments where the stagnation pressures have been systematically increased by more than a factor of 10 by fielding low-entropy implosions through the control of radiation symmetry, small hot electron production, and proper shock timing. The stagnation pressure is above 100 Gbars resulting in high Lawson-type confinement parameters of Pτ≃10 atm s. Comparisons with radiation-hydrodynamic simulations indicate that the pressure is within a factor of three required for reaching ignition and high yield. This will be the focus of future higher-velocity implosions that will employ additional optimizations of hohlraum, capsule and laser pulse shape conditions.