A relativistic electron source based on high power laser interaction with gas jet targets has been developed at the Institute of Plasma Physics and Lasers of the Hellenic Mediterranean University. Initial measurements were conducted using the ‘Zeus’ 45 TW laser with peak intensities in the range of 10 18 –10 19 W cm −2 interacting with a He pulsed gas jet having a 0.8 mm diameter nozzle. A significant improvement of the electron signal was measured after using an absorber to improve the laser pulse contrast from 10 −10 to 10 −11 . A high stability quasi-mono-energetic electron beam of about 50 MeV was achieved and measured using a magnetic spectrometer for pulsed gas jet backing pressure of 12 bar. Supplementary studies using a 3 mm diameter nozzle for backing pressures in the range of 35–40 bar showed electron beam production with energies spread in the range from 50 to 150 MeV. The pulsed jet density profile was determined using interferometric techniques. Particle-in-cell simulations, at the above experimentally determined conditions, support our experimental findings.

The generation of laser based relativistic electron sources involves impressive basic science as well as innovative applications. This study reports first novel qualitative results on polymer-gel radiation dosimetry of ultrafast laser-based relativistic electron beams. The fabricated polymer-gels are irradiated by the ultra-high dose rate (FLASH) laser-generated electron beams and then are analysed using magnetic resonance imaging. The reading of the irradiated dosimeters is performed using a clinical 1.5 T Magnetic Resonance Imaging system. Three-dimensional colour parametric T2 maps are then constructed from the original PD-T2 weighted images obtained from the clinical MRI scanner. For comparison, the gels are also irradiated with standard electron beams of various energies utilizing a radiotherapy clinical linear accelerator system. For the calibration measurements of the gel dosimetry method, special calibrated dosimetric films are also implemented. The preliminary results demonstrate the potential of polymer gel dosimetry for 3D-dose-distribution of FLASH type irradiation of laser generated electron beams. Furthermore, they illustrate potential issues related to the polymer gel based dosimetry in challenging irradiation arrangements, such as the oxygen sensitivity and necessity for oxygen impermeable container material.

The rapid development of high-intensity laser-generated particle and photon secondary sources has attracted widespread interest during the last 20 years not only due to fundamental science research but also because of the important applications of this developing technology. For instance, the generation of relativistic particle beams, betatron-type coherent X-ray radiation and high harmonic generation have attracted interest from various fields of science and technology owing to their diverse applications in biomedical, material science, energy, space, and security applications. In the field of biomedical applications in particular, laser-driven particle beams as well as laser-driven X-ray sources are a promising field of study. This article looks at the research being performed at the Institute of Plasma Physics and Lasers (IPPL) of the Hellenic Mediterranean University Research Centre. The recent installation of the ZEUS 45 TW laser system developed at IPPL offers unique opportunities for research in laser-driven particle and X-ray sources. This article provides information about the facility and describes initial experiments performed for establishing the baseline platforms for secondary plasma sources.

The physical processes that occur at the initial stages of electrical exploding wire are crucial for plasma dynamics in pulsed-power Z-Pinch experiments. During the interaction of a pulsed current with a single wire, the generated Electro-Thermo-Mechanical (ETM) instability in the solid phase acts as a seeding mechanism for the later developed plasma instabilities. 1 The influence of the geometrical characteristics (thickness and length of the wire) on the generation of the ETM and plasma instability is the main focus of this work. Experimental results for the expansion dynamics of the exploded wire are obtained by a modified Fraunhofer diffraction probe method, while three-frames shadowgraphic and interferometric measurements are carried out to study the plasma dynamics and the generated instabilities. Multiphysics-multiphase simulations considering the phase changes from solid to plasma state are performed to validate the experimental measurements. For varying wire thickness and length, the combination of the experimental method and multiphysics modeling is capable to describe satisfactorily the wire expansion dynamics and the growth rate of the developed instabilities.

A high quality, compact 1GHz preamplifier suitable for operation in conjunction with micro channelplates (MCP) and silicon Photomultipliers (SiPM), that is comprised of two integrated circuits is described inthis paper. The amplifier requires no adjustment and has a flat response from low frequencies and adequatebandwidth for high speed measurement systems.

This work presents studies which demonstrate the importance of the very early heating dynamics of the ablator long before the ablation plasma phase begins in laser driven inertial confinement fusion (ICF) studies. For the direct-drive fusion concept using lasers, the development of perturbations during the thermo-elasto-plastic (TEP) and melting phases of the interaction of the laser pulse with the ablator's surface may act as seeding to the subsequent growth of hydro-dynamic instabilities apparent during the acceleration phase of the interaction such as for instance the Rayleigh-Taylor and the Richtmyer-Meshkov, which strongly affect the implosion dynamics of the compression phase. The multiphysics-multiphase finite-element method (FEM) simulation results are experimentally validated by advanced three-dimensional whole-field dynamic imaging of the surface of the ablator allowing for a transverse to the surface spatial resolution of only approximately 1 nm. The study shows that the TEP and melting phases of the interaction are of crucial importance since transverse perturbations of the ablator's surface can reach tens of nanometres in amplitude within the TEP and melting phases. Such perturbations are of Rayleigh type and are transferred from the ablator to the substrate from the very first moments of the interaction. This article is part of a discussion meeting issue 'Prospects for high gain inertial fusion energy (part 1)'.

The computational study of x-pinch plasmas driven by pulsed power generators demands the development of advanced numerical models and simulation schemes, able to enlighten the experiments. The capabilities of PLUTO code are here extended to enable the investigation of low current produced x-pinch plasmas. The numerical modules of the code used and modified are presented and discussed. The simulations results are compared to experiments, carried out on a table-top pulsed power plasma generator implemented in a mode of producing a peak current of ∼45 kA with a rise time (10%–90%) of 50 ns, loaded with Tungsten wires. The structural evolution of plasma density is studied and its influence on the magnetic field is analyzed with the help of the new simulation data. The simulated areal mass density is compared with the experimentally measured dense opaque region to enlighten the dense plasma evolution. In addition, the measured areal electron density is compared to the simulation results. Moreover, the new simulation data offer valuable insights to the main jet formation mechanisms, which are further analyzed and discussed in relation to the influence of the J × B force and the momentum.

A study regarding the characterization of plasma sheath evolution after pinch time in a tabletop size plasma focus (PF), is presented in this work. A 300 J energy Mather-type PF device1,2 is used to carry out the experiments. Shadowgraphy probing using laser pulses of 150 ps duration is the diagnostic implemented for the plasma sheath evolution. Time-series of shadowgrams are used for the characterization of the plasma dynamics in later times after pinching. The expansion of the plasma sheath front in PF is found to be intersected axially by a secondary bubble-like shockwave front. The characteristics of the main and the secondary front dynamics are evaluated and correlated with the experimental parameters. A case of double shockwave is also presented. The obtained results are compared with relevant works and discussion concerning the source of the shockwave is made.

The second and final year of the Erasmus Plus programme ’Innovative Education and Training in high power laser plasmas’, otherwise known as PowerLaPs, is described. The PowerLaPs programme employs an innovative paradigm in that it is a multi-centre programme, where teaching takes place in five separate institutes with a range of different aims and styles of delivery. The ’in-class’ time is limited to 4 weeks a year, and the programme spans 2 years. PowerLaPs aims to train students from across Europe in theoretical, applied and laboratory skills relevant to the pursuit of research in laser plasma interaction physics and inertial confinement fusion. Lectures are intermingled with laboratory sessions and continuous assessment activities. The programme, which is led by workers from the Hellenic Mediterranean University and supported by co-workers from the Queen’s University Belfast, the University of Bordeaux, the Czech Technical University in Prague, Ecole Polytechnique, the University of Ioannina, the University of Salamanca and the University of York, has just finished its second and final year. Six Learning Teaching Training activities have been held at the Queen’s University Belfast, the University of Bordeaux, the Czech Technical University, the University of Salamanca and the Institute of Plasma Physics and Lasers of the Hellenic Mediterranean University. The last of these institutes hosted two 2-week-long Intensive Programmes, while the activities at the other four universities were each 5 days in length. In addition, a ’Multiplier Event’ was held at the University of Ioannina, which will be briefly described. In this second year,the work has concentrated on training in both experimental diagnostics and simulation techniques appropriate to the study of plasma physics, high power laser matter interactions and high energy density physics. The nature of the programme will be described in detail, and some metrics relating to the activities carried out will be presented. In particular, this paper will focus on the overall assessment of the programme.

Imaging detectors that use X-ray radiation and pulsed neutron sources have increased in sophistication in recent years due to the use of solid-state detectors. A key method for neutron detection is the nuclear activation of materials by neutrons. Neutron activation can generate radionuclides whose decay produces secondary particle emission that can be detected without interference from the X-rays and other prompt radiation sources and offers advantages over neutrons detection using scintillators. In this paper, we present the design of an imaging system for fast neutron sources. The imaging system utilizes a microcontroller network that communicates using a modified SPI protocol. This network communicates with an interface unit and passes an image to a personal computer. A computer program has been developed to reconstruct the image.

The current research focuses on the characterization of the produced heat affected zone when laser heats AISI H13 steel, AISI 1045 steel and Ti6Al4V alloy workpieces via finite element simulations and experimental investigation. The surface roughness designedly varies on the surface of the samples and its influence on the absorption of laser light is investigated. Experiments are conducted at 1-4 W laser power and for two scanning speeds of 2 and 100 mm/min. A 3D transient thermo-structural finite element model for a moving Gaussian laser heat source is developed to simulate the micromachining process and predict the depth and width of the heat affected zone. The Johnson-Cook material model that takes into account the effect of plastic strain, strain rate and temperature, along with a fracture model, is adapted to the simulations. A good agreement between the experimental data and the simulation results is found. The depth and width of the heat affected zone strongly depend on the laser parameters and material properties of the irradiated samples. This study constitutes the basis to the optimization and improvement of the laser assisted micromachining process parameters and provides key insights on the roughness-absorptivity relation for the three metallic materials.

This article addresses key features for the implementation of low current pulsed power plasma devices for the study of matter dynamics from the solid to the plasma phase. The renewed interest in such low current plasma devices lies in the need to investigate methods for the mitigation of prompt seeding mechanisms for the generation of plasma instabilities. The low current when driven into thick wires (skin effect mode) allows for the simultaneous existence of all phases of matter from solid to plasma. Such studies are important for the concept of inertial confinement fusion where the mitigation of the instability seeding mechanisms arising from the very early moments within the target's heating is of crucial importance. Similarly, in the magnetized liner inertial fusion concept it is an open question as to how much surface non-uniformity correlates with the magneto-Rayleigh-Taylor instability, which develops during the implosion. This study presents experimental and simulation results, which demonstrate that the use of low current pulsed power devices in conjunction with appropriate diagnostics can be important for studying seeding mechanisms for the imminent generation of plasma instabilities in future research.

The study of plasma instabilities is a research topic with fundamental importance since for the majority of plasma applications they are unwanted and there is always the need for their suppression. The initiating physical processes that seed the generation of plasma instabilities are not well understood in all plasma geometries and initial states of matter. For most plasma instability studies, using linear or even nonlinear magnetohydrodynamics (MHD) theory, the most crucial step is to correctly choose the initial perturbations imposed either by a predefined perturbation, usually sinusoidal, or by randomly seed perturbations as initial conditions. Here, we demonstrate that the efficient study of the seeding mechanisms of plasma instabilities requires the incorporation of the intrinsic real physical characteristics of the solid target in an electro-thermo-mechanical multiphysics study. The present proof-of-principle study offers a perspective to the understanding of the seeding physical mechanisms in the generation of plasma instabilities.

Measurements of the spatial and time-resolved characteristics of pulsed neutron sources require large area detection materials and fast circuitry that can process the electronic pulses readout from the active region of the detector. In this paper, we present a solid-state detector based on the nuclear activation of materials by neutrons, and the detection of the secondary particle emission of the generated radionuclides’ decay. The detector utilizes a microcontroller that communicates using a modified SPI protocol. A solid-state, pulse shaping filter follows a charge amplifier, and it is designed as an inexpensive, low-noise solution for measuring pulses measured by a digital counter. An imaging detector can also be made by using an array of these detectors. The system can communicate with an interface unit and pass an image to a personal computer.

A novel trigger generator for operating a pseudospark switch has been developed based on a series connection of several insulated gate bipolar transistors. The trigger generator can be operated in single shot mode up to a repetition rate of 1 kHz. It is characterized by a fast rise time and low jitter between the output trigger pulses of less than 1 ns. It produces 3 kV, 1 μs pulses into a 50 Ω load that can trigger a pseudospark switch. By eliminating bulkier, slower high voltage components, the overall volume of the trigger generator is reduced. This allows for faster, high voltage switching to take place and thereby increasing the power density of the unit. Using this pseudospark trigger generator, it is possible to trigger single or multiple pseudospark gaps without the requirement to use a pulse shaping circuit.

The design and construction of a pulsed plasma focus device to be used as a portable neutron source for material analysis such as explosive detection using gamma spectroscopy is presented. The device is capable of operating at a repetitive rate of a few Hz. When deuterium gas is used, up to 105 neutrons per shot are expected to be produced with a temporal pulse width of a few tens of nanoseconds. The pulsed operation of the device and its portable size are its main advantage in comparison with the existing continuous neutron sources. Parts of the device include the electrical charging unit, the capacitor bank, the spark switch (spark gap), the trigger unit and the vacuum–fuel chamber / anode–cathode. Numerical simulations are used for the simulation of the electrical characteristics of the device including the scaling of the capacitor bank energies with total current, the pinch current, and the scaling of neutron yields with energies and currents. The MCNPX code is used to simulate the moderation of the produced neutrons in a simplified geometry and subsequently, the interaction of thermal neutrons with a test target and the corresponding prompt γ-ray generation.

There is an increasing requirement for alternative and improved detection of fast neutrons due to the renewed interest in neutron diagnostics applications. Some applications require heavily shielded neutron sources that emit a substantial proportion of their emission as fast neutrons and so require high performance fast neutron detectors. In some applications, the detection of neutron bursts from pulsed neutron sources has to be synchronized to the repetition rate of the source. Typical fast neutron detectors incorporate scintillators that are sensitive to all kinds of ionizing radiations as well as neutrons, and their efficiency is low. In this paper, we present a device based on the principle of neutron activation coupled to solid-state p-i-n diodes connected to a charge amplifier. The charge amplifier is specially developed to operate with high capacitance detectors and has been optimized by the aid of the SPICE program. A solid-state pulse shaping filter follows the charge amplifier, as an inexpensive solution, capable to provide pulses that can be counted by a digital counter.

A photon detector suitable for the measurement of bremsstrahlung spectra generated in relativistically intense laser-solid interactions is described. The Monte Carlo techniques used to extract the fast electron spectrum and laser energy absorbed into forward-going fast electrons are detailed. A relativistically intense laser-solid experiment using frequency doubled laser light is used to demonstrate the effective operation of the detector. The experimental data were interpreted using the 3-spatial-dimension Monte Carlo code MCNPX [D. Pelowitz, MCNPX User's Manual Version 2.6.0, Los Alamos National Laboratory, 2008], and the fast electron temperature found to be 125 keV.

Experimental measurements of the fast electron beam created by the interaction of relativistically intense, frequency-doubled laser light with planar solid targets and its subsequent transport within the target are presented and compared with those of a similar experiment using the laser fundamental frequency. Using frequency-doubled laser light, the fast electron source size is significantly reduced, while evidence suggests the divergence angle may be reduced. Pyrometric measurements of the target rear surface temperature and the Cu Kα imager data indicate the laser to fast electron absorption fraction is reduced using frequency doubled laser light. Bremsstrahlung measurements indicate the fast electron temperature is 125 keV, while the laser energy absorbed into forward-going fast electrons was found to be 16 ± 4% for frequency doubled light at a mean laser intensity of 5 ± 3 × 1018 W cm−2.

The HiPER infrastructure reprsents a uniquely valuable tool for scientific discovery because it will be able to generate extreme matter conditions similar to those existing in our sun and the universe. The existence of long and short laser pulses in one infrastructure is fascinating and will allow for the study of new branches of physics suck as the properties of matter under extremer conditions in the laboratory. HiPER is therefore being designed to enable a broad area of new science studies including warm dense matter studies, astrophysics in the laboratory, extreme mater studies (under extreme magnetic and electric fields), highly nonlinear laser plasma interactions etc. The scope of this presentation is to present the progress of work on: a) the fundamental science target area design and b) the shielding requirements for the fundamental science programme.