A dual-radiator Ring Imaging Cherenkov (dRICH) will provide charged hadrons particle identification in the hadronic end-cap of a general-purpose experiment at the future Electron–Ion Collider (EIC). We developed a prototype to test the performance and validate the use of Silicon Photo-Multipliers (SiPM), the baseline photo-sensor candidate for the dRICH. They provide a cheap, highly efficient technology and they are not sensitive to the high magnetic field. The general features of the detector, a detailed view of the prototype and its different configurations, the test beam performed, and the preliminary results we obtained are presented.

The performance of the electromagnetic calorimeter of the ALICE experiment during operation in 2010–2018 at the Large Hadron Collider is presented. After a short introduction into the design, readout, and trigger capabilities of the detector, the procedures for data taking, reconstruction, and validation are explained. The methods used for the calibration and various derived corrections are presented in detail. Subsequently, the capabilities of the calorimeter to reconstruct and measure photons, light mesons, electrons and jets are discussed. The performance of the calorimeter is illustrated mainly with data obtained with test beams at the Proton Synchrotron and Super Proton Synchrotron or in proton-proton collisions at √s = 13 TeV, and compared to simulations.

ATHENA has been designed as a general purpose detector capable of delivering the full scientific scope of the Electron-Ion Collider. Careful technology choices provide fine tracking and momentum resolution, high performance electromagnetic and hadronic calorimetry, hadron identification over a wide kinematic range, and near-complete hermeticity. This article describes the detector design and its expected performance in the most relevant physics channels. It includes an evaluation of detector technology choices, the technical challenges to realizing the detector and the R D required to meet those challenges.

This report describes the physics case, the resulting detector requirements, and the evolving detector concepts for the experimental program at the Electron-Ion Collider (EIC). The EIC will be a powerful new high-luminosity facility in the United States with the capability to collide high-energy electron beams with high-energy proton and ion beams, providing access to those regions in the nucleon and nuclei where their structure is dominated by gluons. Moreover, polarized beams in the EIC will give unprecedented access to the spatial and spin structure of the proton, neutron, and light ions. The studies leading to this document were commissioned and organized by the EIC User Group with the objective of advancing the state and detail of the physics program and developing detector concepts that meet the emerging requirements in preparation for the realization of the EIC. The effort aims to provide the basis for further development of concepts for experimental equipment best suited for the science needs, including the importance of two complementary detectors and interaction regions. This report consists of three volumes. Volume I is an executive summary of our findings and developed concepts. In Volume II we describe studies of a wide range of physics measurements and the emerging requirements on detector acceptance and performance. Volume III discusses general-purpose detector concepts and the underlying technologies to meet the physics requirements. These considerations will form the basis for a world-class experimental program that aims to increase our understanding of the fundamental structure of all visible matter

We report the results of the analyses of the cosmic ray data collected with a 4 tonne (3×1×1 m3) active mass (volume) Liquid Argon Time-Projection Chamber (TPC) operated in a dual-phase mode. We present a detailed study of the TPC's response, its main detector parameters and performance. The results are important for the understanding and further developments of the dual-phase technology, thanks to the verification of key aspects, such as the extraction of electrons from liquid to gas and their amplification through the entire one square metre readout plain, gain stability, purity and charge sharing between readout views.

The 3×1×1 m 3 demonstrator is a dual phase liquid argon time projection chamber that has recorded cosmic rays events in 2017 at CERN. The light signal in these detectors is crucial to provide precise timing capabilities. The performance of the photon detection system, composed of five PMTs, are discussed. The collected scintillation and electroluminescence light created by passing particles has been studied in various detector conditions. In particular, the scintillation light production and propagation processes have been analyzed and compared to simulations, improving the understanding of some liquid argon properties.

ABSTRACT A new Large-Acceptance Forward Angle Spectrometer [Super Bigbite Spectrometer (SBS)], is under development for the upcoming experiments in Hall A at the Thomas Jefferson National Accelerator Facility (Virginia, USA), where a longitudinally polarized (up to ) electron beam up to 12 GeV energy is now available. The excellent beam intensity (up to 100 A), combined with innovative polarized targets, will provide luminosity up to , opening interesting opportunities to investigate unexplored aspects of the inner structure of the nucleons. In one of the most demanding configuration, the new spectrometer will consist of a dipole magnet, one front charged particle tracker, two identical proton polarimeters with related back trackers and a segmented hadron calorimeter. The front tracker, placed just after the dipole magnet, consists of up to six layers of large area GEM (Gas Electron Multiplier) chambers (); each chamber is made by three adjacent GEM modules of active rectangular area (18 modules as a total). We have chosen the GEM technology in order to optimize spatial resolution (∼80 mm), high hit rate (), cost/performance and high radiation hardness. We present the main features of the SBS front tracker and its GEM detectors and, finally, we discuss the ongoing tracker commissioning at JLab and show some representative test results.

A 10 kilo-tonne dual-phase liquid argon TPC is one of the detector options considered for the Deep Underground Neutrino Experiment (DUNE). The detector technology relies on amplification of the ionisation charge in ultra-pure argon vapour and offers several advantages compared to the traditional single-phase liquid argon TPCs. A 4.2 tonne dual-phase liquid argon TPC prototype, the largest of its kind, with an active volume of \three has been constructed and operated at CERN. In this paper we describe in detail the experimental setup and detector components as well as report on the operation experience. We also present the first results on the achieved charge amplification, prompt scintillation and electroluminescence detection, and purity of the liquid argon from analyses of a collected sample of cosmic ray muons.

This document presents the Conceptual Design Report (CDR) put forward by an international neutrino community to pursue the Deep Underground Neutrino Experiment at the Long-Baseline Neutrino Facility (LBNF/DUNE), a groundbreaking science experiment for long-baseline neutrino oscillation studies and for neutrino astrophysics and nucleon decay searches. The DUNE far detector will be a very large modular liquid argon time-projection chamber (LArTPC) located deep underground, coupled to the LBNF multi-megawatt wide-band neutrino beam. DUNE will also have a high-resolution and high-precision near detector.

A Large-Acceptance Forward Angle Spectrometer (Super BigBite) is under development for the upcoming experiments in Hall A at Jefferson Lab to optimally exploit the exciting opportunities offered by the 12GeV upgrade of the electron beam. The tracking of this new apparatus is based on the Gas Electron Multiplier technology, which has been chosen to optimize cost/performance, position resolution and meet the high hits rate (>1MHz/cm(2)). In this report we present the technical features of the detector and comment on the presently achieved performance.

A description of the proposed detector(s) for DUNE at LBNF

This document presents the Conceptual Design Report (CDR) put forward by an international neutrino community to pursue the Deep Underground Neutrino Experiment at the Long-Baseline Neutrino Facility (LBNF/DUNE), a groundbreaking science experiment for long-baseline neutrino oscillation studies and for neutrino astrophysics and nucleon decay searches. The DUNE far detector will be a very large modular liquid argon time-projection chamber (LArTPC) located deep underground, coupled to the LBNF multi-megawatt wide-band neutrino beam. DUNE will also have a high-resolution and high-precision near detector.

A new collaboration is being formed to develop a multi-kiloton Long-Baseline neutrino experiment that will be located at the Surf Underground Research Facility (SURF) in Lead, SD. In the present design, the detector will be located inside cryostats filled with 68,400 ton of ultrapure liquid argon (less than 100 parts per trillion of oxygen equivalent contamination). To qualify the membrane technology for future very large-scale and underground implementations, a strong prototyping effort is ongoing: several smaller detectors of growing size with associated cryostats and cryogenic systems will be designed and built at Fermilab and CERN. They will take physics data and test different detector elements, filtration systems, design options and installation procedures. In addition, a 35 ton prototype is already operational at Fermilab and will take data with single-phase detector in early 2016. After the prototyping phase, the multi-kton detector will be constructed. After commissioning, it will detect and study neutrinos from a new beam from Fermilab. These cryostats will be engineered, constructed, commissioned, and qualified by an international engineering team. This contribution presents the on-going effort on the development of the cryostats and details the requirements and the current status of the design.

The Physics Program for the Deep Underground Neutrino Experiment (DUNE) at the Fermilab Long-Baseline Neutrino Facility (LBNF) is described.

A new Large-Acceptance Forward Angle Spectrometer (Super BigBite) is under development at JLab/Hall A for the upcoming experiments in Hall A at Jefferson Lab where a longitudinally polarized electron beam of 11 GeV is now available. This beam, combined with innovative polarized targets will provided luminosity up to 1039 /(s·cm 2 ) opening exciting opportunities to investigate unexplored aspects of the inner structure of the nucleon. The tracker of this new apparatus is based on the Gas Electron Multiplier (GEM) technology, which has been chosen to optimize cost/performance, position resolution and to meet the high hit rate (>1 MHz/cm 2 ). The first GEM detector modules, designed and built by the INFN Collaboration JLAB12, were tested at the DESY test beam facility in Hamburg, by using an electron beam with energy ranging from 2.0 to 6.0 GeV. In particular, three 40x50 cm 2 GEM chambers were equipped with a new implementation of the APV25 readout chip. Measurements were performed at different impact points and angles between the electron beam and the plane of the GEM chambers, with one large chamber in a solenoid magnetic field up to 500 Gauss. In this paper we present the technical features of the tracker and comment on the presently achieved performance.

A new Large-Acceptance Forward Angle Spectrometer (Super BigBite) is under development at JLab/Hall A to optimally exploit the exciting opportunities offered by the 12 GeV upgrade of the electron beam. The tracking of this new apparatus is based on the gas electron multiplier technology, which has been chosen to optimize cost/performance, position resolution and meet the high hits rate (>1 MHz/cm2). The first gas electron multiplier detector prototypes were designed, built and tested at the DESY test beam facility in Hamburg, by using an electron beam with energy from 2.0 to 6.0 GeV. In particular, two gas electron multiplier chambers (10 x 10 cm2 and 40 x 50 cm2, respectively) were equipped with a new implementation of the APV25 readout chip. Measurements were performed at different impact points and angles between the electron beam and the plane of the gas electron multiplier chambers. In this report we present the technical characteristics of the detector and comment on the presently achieved performance.

The physics case and an experimental overview of the MOLLER (Measurement Of a Lepton Lepton Electroweak Reaction) experiment at the 12 GeV upgraded Jefferson Lab are presented. A highlight of the Fundamental Symmetries subfield of the 2007 NSAC Long Range Plan was the SLAC E158 measurement of the parity-violating asymmetry A_PV in polarized electron-electron (Møller) scattering. The proposed MOLLER experiment will improve on this result by a factor of five, yielding the most precise measurement of the weak mixing angle at low or high energy anticipated over the next decade. This new result would be sensitive to the interference of the electromagnetic amplitude with new neutral current amplitudes as weak as ∼ 10^-3· G_F from as yet undiscovered dynamics beyond the Standard Model. The resulting discovery reach is unmatched by any proposed experiment measuring a flavor- and CP-conserving process over the next decade, and yields a unique window to new physics at MeV and multi-TeV scales, complementary to direct searches at high energy colliders such as the Large Hadron Collider (LHC). The experiment takes advantage of the unique opportunity provided by the upgraded electron beam energy, luminosity, and stability at Jefferson Laboratory and the extensive experience accumulated in the community after a round of recent successfully completed parity-violating electron scattering experiments

The gas electron multiplier technology has been proven to tolerate rat e larger than 50 MHz/cm2 without noticeable aging and to provide sub resolution on working chambers up to 45 cm x 45 cm. A new gas electron multiplier-based tracker is under development for the Hall A upgrade at Jefferson Lab. The chambers of the tracker have been designed in a modular way: each chamber consists of 3 adjacent gas electron multiplier modules, with an active area of 40 cm x 50 cm each. We optimized the gas flow inside the gas electron multiplier module volume, using the COMSOL physics simulator framework; the COMSOL-based analysis includes the design of the inlet and outlet pipes and the maximization of the uniformity of the gas flow. We have defined the procedures for the assembling of the gas electron multiplier modules and designed a mechanical system (TENDIGEM) that will be used to stretch the GEM foils at the proper tension (few kg/cm); the TENDIGEM is based on the original design developed at LNF.