The European DEMO is a pulsed device with pulse length of 2 hours. The functions devoted to the heating and current drive system are: plasma breakdown, plasma ramp-up to the flat-top where fusion reactions occur, the control of the plasma during the flat-top phase, and finally the plasma ramp-down. The EU-DEMO project was in a Pre-Concept Design Phase during 2014-2020, meaning that in some cases, the design values of the device and the precise requirements from the physics point of view were not yet frozen. A total of 130 MW was considered for the all phases of the plasma: in the flat top, 30 MW is required for neoclassical tearing modes (NTM) control, 30 MW for burn control, and 70 MW for the control of thermal instability (TI), without any specific functions requested from each system, Electron Cyclotron (EC), Ion Cyclotron (IC), or Neutral Beam (NB) Injection. At the beginning of 2020, a strategic decision was taken, to consider EC as the baseline for the next phase (in 2021 and beyond). R&D on IC and NB will be risk mitigation measures. In parallel with progresses in Physics modelling, a decision point on the heating strategy will be taken by 2024. This paper describes the status of the R&D development during the period 2014-2020. It assumes that the 3 systems EC, IC and NB will be needed. For integration studies, they are assumed to be implemented at a power level of at least 50 MW. This paper describes in detail the status reached by the EC, IC and NB at the end of 2020. It will be used in the future for further development of the baseline heating method EC, and serves as starting point to further develop IC and NB in areas needed for these systems to be considered for DEMO.

We present recent highlights from the most recent operation phases of Wendelstein 7-X, the most advanced stellarator in the world. Stable detachment with good particle exhaust, low impurity content, and energy confinement times exceeding 100 ms, have been maintained for tens of seconds. Pellet fueling allows for plasma phases with reduced ion-temperature-gradient turbulence, and during such phases, the overall confinement is so good (energy confinement times often exceeding 200 ms) that the attained density and temperature profiles would not have been possible in less optimized devices, since they would have had neoclassical transport losses exceeding the heating applied in W7-X. This provides proof that the reduction of neoclassical transport through magnetic field optimization is successful. W7-X plasmas generally show good impurity screening and high plasma purity, but there is evidence of longer impurity confinement times during turbulence-suppressed phases.

In this paper, we investigate the CO 2 emissions caused by nuclear and renewable power generation. The knowledge of the share of coal, gas and oil in electricity generation permits the exact calculation of the related CO 2 emissions. In addition, there is a second approach especially within the economic sciences, which applies statistical techniques for the study of the energy-related emissions. The background for these studies is the provision of general political advice and the expectation that political, cultural, or infrastructural considerations guide nations in the preference and choice of specific technologies. In this paper, we are applying both approaches and come to the certain conclusion, that nuclear power is as effective as renewable power in order to reduce the CO 2 emissions. Our results are in complete contradiction to a recent publication (Sovacool et al. in Nat Energy 5:928–935, 2020. https://doi.org/10.1038/s41560-020-00696-3 ). The authors of this paper conclude that nuclear power does not reduce the CO 2 emissions, but renewable power efficiently does. In addition, they argue that these two technologies crowd out each other. The possible reason for their claims may result from a specific conditioning of the data. In contrast, our analysis clearly confirms the adequacy of both nuclear and renewable power generation.

The coupling of laser energy to electrons is fundamental to almost all topics in intense laser-plasma interactions, including laser-driven particle and radiation generation, relativistic optics, inertial confinement fusion and laboratory astrophysics. We report measurements of total energy absorption in foil targets ranging in thickness from 20 mu m, for which the target remains opaque and surface interactions dominate, to 40 nm, for which expansion enables relativistic-induced transparency and volumetric interactions. We measure a total peak absorption of similar to 80% at an optimum thickness of similar to 380 nm. For thinner targets, for which some degree of transparency occurs, although the total absorption decreases, the number of energetic electrons escaping the target increases. 2D particle-in-cell simulations indicate that this results from direct laser acceleration of electrons as the intense laser pulse propagates within the target volume. The results point to a trade-off between total energy coupling to electrons and efficient acceleration to higher energies.

A series of ice pellets was injected into the advanced stellarator Wendelstein 7-X (W7-X). Although the pellets were small and slow, deep and efficient particle fueling could be observed experimentally. The most striking feature appearing after the injection of the pellets, however, was a transient increase in the energy confinement time. This transient phase resembled in several aspects modes of enhanced confinement after gas-puff or pellet injection, as observed in other fusion experiments. All experimental attempts, to prolong this phase, failed. In this paper, discharges are described that show the enhanced energy confinement, and some conditions are summarized which seem to be essential in order to generate it. The focus here is on deep particle fueling by pellets, and shaping of the density profiles during and after the series of pellets. During this time, neutral gas particle re-fueling at the plasma edge is reduced, while density profile peaking and low impurity radiation losses are present.

For the first time, the optimized stellarator Wendelstein 7-X has operated with an island divertor. An operation regime in hydrogen was found in which the total plasma radiation approached the absorbed heating power without noticeable loss of stored energy. The divertor thermography recorded simultaneously a strong reduction of the heat load on all divertor targets, indicating almost complete power detachment. This operation regime was stably sustained over several energy confinement times until the preprogrammed end of the discharge. The plasma radiation is mainly due to oxygen and is located at the plasma edge. This plasma scenario is reproducible and robust at various heating powers, plasma densities, and gas fueling locations. These experimental results show that the island divertor concept actually works and displays good power dissipation potential, producing a promising exhaust concept for the stellarator reactor line.

During the two most recent experimental campaigns in the advanced stellarator Wendelstein 7-X (W7-X) (Klinger et al 2017 Plasma Phys. Control. Fusion 59 014018; Bosch et al 2017 Nucl. Fusion 57 116015; Wolf et al 2017 Nucl. Fusion 57 102020; Pedersen et al 2017 Phys. Plasmas 24 0555030) hydrogen ice pellet injection was performed for the first time. In order to investigate the potential of pellet fueling in W7-X and to study the particle deposition in a large stellarator, a blower-gun system was installed with 40 pellets capability. The experience gained with this system will be used for the specification of a future steady-state pellet injector system. One important motivation for a pellet injector (Dibon 2014 Master-Thesis Technical University Munich, Max-Planck Institut IPP) on W7-X is the mitigation of hollow density profiles expected in case of predominant neoclassical transport. For long-pulse operation of up to 30 min, only electron cyclotron resonance heating is available on W7-X. Hence, pellet injection will be the only source for deep particle fueling. Deep particle fueling by pellets in tokamaks is supported by a grad-B drift, if the pellets are injected from the magnetic high-field-side. This approach was tested in W7-X, as well. The injection of series of pellets was also tested. Here, deep fueling is supported for later pellets in the series by the plasma cooling following the initial pellets in the same series. As in earlier experiments in the heliotron LHD (Takeiri et al 2017 Nucl. Fusion 57 102023), deep and rapid fueling could be achieved successfully in W7-X.

This article discusses possible hurdles foreseen by a large-scale introduction of intermittent renewable energies (described as “ RE ” hereafter) from wind and photo-voltaic (the latter “ PV ” hereafter) powers. The analysis was carried out using actual recent load, wind and PV data of 15 min resolutions of Kyushu Electric Power Co. The results indicate the following three conclusions: (1) the surplus energy and grid power would become large once the proportion of the annually produced energy by RE would become above 40 % of the total annual electric load, (2) CO 2 emission from back-up systems due to thermal power stations burning fossil fuels did not go down much even by a large amount of RE introduction, and (3) in order to ameliorate this situation and for RE to be implemented of its full potential, an increase of the present pumped storage capacity of Kyushu Electric Power Co. by more than a few tens of times is necessary.

The optimized superconducting stellarator device Wendelstein 7-X (with major radius , minor radius , and plasma volume) restarted operation after the assembly of a graphite heat shield and 10 inertially cooled island divertor modules. This paper reports on the results from the first high-performance plasma operation. Glow discharge conditioning and ECRH conditioning discharges in helium turned out to be important for density and edge radiation control. Plasma densities of with central electron temperatures were routinely achieved with hydrogen gas fueling, frequently terminated by a radiative collapse. In a first stage, plasma densities up to were reached with hydrogen pellet injection and helium gas fueling. Here, the ions are indirectly heated, and at a central density of a temperature of with was transiently accomplished, which corresponds to with a peak diamagnetic energy of and volume-averaged normalized plasma pressure . The routine access to high plasma densities was opened with boronization of the first wall. After boronization, the oxygen impurity content was reduced by a factor of 10, the carbon impurity content by a factor of 5. The reduced (edge) plasma radiation level gives routinely access to higher densities without radiation collapse, e.g. well above line integrated density and central temperatures at moderate ECRH power. Both X2 and O2 mode ECRH schemes were successfully applied. Core turbulence was measured with a phase contrast imaging diagnostic and suppression of turbulence during pellet injection was observed.

Human beings grew in numbers as any other biological system would do under favourable living conditions. The growth of mankind up to presently 7.5 bn people was enabled by the access to cheap energy. Technology made it possible to exploit fossil fuels at large scale and to transform the chemically bound energy into different forms for practical application. Figure 1 shows the growth of the US population between 1835 and 2009. Initially, at still a small population, the renewable energy (RE) share in the energy demand was high, close to 1. In course of time, the share of nuclear and fossil energy grew at the expense of REs. This historical evolution is representative for most industrialised countries. The interrelation between energy consumption by a growing population and the population growth by energy availability is, however, not “free lunch”. Figure 2 shows the increase of world energy consumption being steeper than the growth of world population. However, about 80% of primary energy use gives rise to CO2 emissions. Mankind is suddenly faced with the threat of climate change. In the future, the course has to be reversed back to large RE shares but under conditions where large populations, 300 Mill people in case of USA (see fig. 1), have to be safely and economically supplied by energy. As nutrition, clean water, healthy living conditions all depend on access to energy a classical conflict emerged in the last decade between efforts to locally improve living conditions by higher energy use and the threat of thereby jeopardising the global living conditions if energy consumption causes CO2 release in the atmosphere as is the case up

A dual ion species plasma expansion scheme from a novel target structure is introduced, in which a nanometer-thick layer of pure deuterium exists as a buffer species at the target-vacuum interface of a hydrogen plasma. Modeling shows that by controlling the deuterium layer thickness, a composite H^{+}/D^{+} ion beam can be produced by target normal sheath acceleration (TNSA), with an adjustable ratio of ion densities, as high energy proton acceleration is suppressed by the acceleration of a spectrally peaked deuteron beam. Particle in cell modeling shows that a (4.3±0.7)  MeV per nucleon deuteron beam is accelerated, in a directional cone of half angle 9°. Experimentally, this was investigated using state of the art cryogenic targetry and a spectrally peaked deuteron beam of (3.4±0.7)  MeV per nucleon was measured in a cone of half angle 7°-9°, while maintaining a significant TNSA proton component.

Fusion energy is one of the options to contribute to the energy demand of future generations without adding to global warming. In this paper, we present the status of fusion energy research on the basis of magnetic confinement. Fusion energy is one of the options to contribute to the energy demand of future generations without contributing to global warming. In this paper, we present the status of fusion energy research on the basis of magnetic confinement. In France, the first fusion reactor ITER is under construction. Its success will be measured on the expectation to deliver 500 MW thermal power—a factor of 10 above the power to maintain the energy producing process. ITER is based on the tokamak concept. In addition, Wendelstein 7-X, an ambitious stellarator, has recently started operation. Both confinement concepts—the tokamak and the stellarator—will be discussed along with general topics regarding fusion technology, operational safety, fusion waste, possible electricity costs, and roadmaps toward a fusion reactor as a power source.

Often, the interpretation of experiments concerning the manipulation of the energy distribution of laser-accelerated ion bunches is complicated by the multitude of competing dynamic processes simultaneously contributing to recorded ion signals. Here we demonstrate experimentally the acceleration of a clean proton bunch. This was achieved with a microscopic and three-dimensionally confined near critical density plasma, which evolves from a 1 µm diameter plastic sphere, which is levitated and positioned with micrometer precision in the focus of a Petawatt laser pulse. The emitted proton bunch is reproducibly observed with central energies between 20 and 40 MeV and narrow energy spread (down to 25%) showing almost no low-energetic background. Together with three-dimensional particle-in-cell simulations we track the complete acceleration process, evidencing the transition from organized acceleration to Coulomb repulsion. This reveals limitations of current high power lasers and viable paths to optimize laser-driven ion sources.

Increasing the pressure by additional heating of magnetically confined plasmas had the consequence that turbulent processes became more violent and plasma confinement degraded. Since this experience from the early 1980ies, fusion research was dominated by the search for confinement regimes with improved properties. It was a gratifying experience that toroidally confined plasmas are able to self-organise in such a way that turbulence diminishes, resulting in a confinement with good prospects to reach the objectives of fusion R&D. The understanding of improved confinement regimes revolutionized the understanding of turbulent transport in high-temperature plasmas. In this paper the story of research into improved confinement regimes will be narrated starting with 1980.

One order of magnitude energy enhancement of the target surface electron beams with central energy at 11.5 MeV is achieved by using a 200 TW, 500 fs laser at an incident angle of 72 degrees with a prepulse intensity ratio of 5 x 10(-6). The experimental results demonstrate the scalability of the acceleration process to high electron energy with a longer (sub-picosecond) laser pulse duration and a higher laser energy (120 J). The total charge of the beam is 400 +/- 20 pC(E > 2.7 MeV). Such a high orientation and mono-energetic electron jet would be a good method to solve the problem of the large beam divergence in fast ignition schemes and to increase the laser energy deposition on the target core. (C) 2018 Optical Society of America

The absorption of laser energy and dynamics of energetic electrons in dense plasma is fundamental to a range of intense laser-driven particle and radiation generation mechanisms. We measure the total reflected and scattered laser energy as a function of intensity, distinguishing between the influence of pulse energy and focal spot size on total energy absorption, in the interaction with thin foils. We confirm a previously published scaling of absorption with intensity by variation of laser pulse energy, but find a slower scaling when changing the focal spot size. 2D particle-in-cell simulations show that the measured differences arise due to energetic electrons recirculating within the target and undergoing multiple interactions with the laser pulse, which enhances absorption in the case of large focal spots. This effect is also shown to be dependent on the laser pulse duration, the target thickness and the electron beam divergence. The parameter space over which this absorption enhancement occurs is explored via an analytical model. The results impact our understanding of the fundamental physics of laser energy absorption in solids and thus the development of particle and radiation sources driven by intense laser–solid interactions.

Laser-driven neutrons are generated by the conversion of laser-accelerated ions via nuclear reactions inside a converter material. We present results from an experimental campaign at the PHELIX laser at GSI in Darmstadt where protons and deuterons were accelerated from thin deuterated plastic foils with thicknesses in the μm and sub-μm range. The neutrons were generated inside a sandwich-type beryllium converter, leading to reproducible neutron numbers around 1011 neutrons per shot. The angular distribution was measured with a high level of detail using up to 30 bubble detectors simultaneously. It shows a laser forward directed component of up to 1.42 × 1010 neutrons per steradian, corresponding to a dose of 43 mrem scaled to a distance of 1 m from the converter.

The new Electricity Market Act (2.0) in Germany is to increase the share of renewable energy through an efficient market design and new regulatory framework. This has paved the way for further participation of different flexibility solutions (such as distributed energy storage) in the German balancing market. This paper examines the market value of electrical energy storage (EES) in the German day-ahead and balancing markets. We present a simple but robust mixed integer optimization model for profit maximization of storage in the day-ahead market. We examine five different energy storage technologies, i.e., pumped hydro storage (PHS), compressed air energy storage (CAES), NaS, Lead-acid, and Li-ion battery energy storage systems. The results show that the benefits from price arbitrage can cover up to 25% of the life cycle cost of EES. However, inclusion of benefits from reserve markets suggests return on investment for some systems like PHS. Aggregation of benefits from energy and reserve markets may not realize profitability for high-cost batteries with cost data in 2016. The theoretical sum of benefits from reserve services, however, suggests a breakeven in the cost-benefit of low-cost batteries with a long discharge time.

After completing the main construction phase of Wendelstein 7-X (W7-X) and successfully commissioning the device, first plasma operation started at the end of 2015. Integral commissioning of plasma start-up and operation using electron cyclotron resonance heating (ECRH) and an extensive set of plasma diagnostics have been completed, allowing initial physics studies during the first operational campaign. Both in helium and hydrogen, plasma breakdown was easily achieved. Gaining experience with plasma vessel conditioning, discharge lengths could be extended gradually. Eventually, discharges lasted up to 6 s, reaching an injected energy of 4 MJ, which is twice the limit originally agreed for the limiter configuration employed during the first operational campaign. At power levels of 4 MW central electron densities reached 3 x 10(19) m(-3), central electron temperatures reached values of 7 keV and ion temperatures reached just above 2 keV. Important physics studies during this first operational phase include a first assessment of power balance and energy confinement, ECRH power deposition experiments, 2nd harmonic O-mode ECRH using multi-pass absorption, and current drive experiments using electron cyclotron current drive. As in many plasma discharges the electron temperature exceeds the ion temperature significantly, these plasmas are governed by core electron root confinement showing a strong positive electric field in the plasma centre.

We report on a novel technique to reduce the noise level in scanning third order cross-correlation. Large angles between the interacting beams combined with adapted crystal parameters lead to a significant decrease of noise photon generation while maintaining efficient generation of the third order signal. An enhanced scanning cross-correlator was developed based on the new technique proposed. In tests at the PHELIX laser facility this novel correlator performed within a dynamic range of 12.5 orders of magnitude.