Hydrogen energy-based electrochemical energy conversion technologies offer the promise of enabling a transition of the global energy landscape from fossil fuels to renewable energy. Here, we present a comprehensive review of the fundamentals of electrocatalysis in alkaline media and applications in alkaline-based energy technologies, particularly alkaline fuel cells and water electrolyzers. Anion exchange (alkaline) membrane fuel cells (AEMFCs) enable the use of nonprecious electrocatalysts for the sluggish oxygen reduction reaction (ORR), relative to proton exchange membrane fuel cells (PEMFCs), which require Pt-based electrocatalysts. However, the hydrogen oxidation reaction (HOR) kinetics is significantly slower in alkaline media than in acidic media. Understanding these phenomena requires applying theoretical and experimental methods to unravel molecular-level thermodynamics and kinetics of hydrogen and oxygen electrocatalysis and, particularly, the proton-coupled electron transfer (PCET) process that takes place in a proton-deficient alkaline media. Extensive electrochemical and spectroscopic studies, on single-crystal Pt and metal oxides, have contributed to the development of activity descriptors, as well as the identification of the nature of active sites, and the rate-determining steps of the HOR and ORR. Among these, the structure and reactivity of interfacial water serve as key potential and pH-dependent kinetic factors that are helping elucidate the origins of the HOR and ORR activity differences in acids and bases. Additionally, deliberately modulating and controlling catalyst-support interactions have provided valuable insights for enhancing catalyst accessibility and durability during operation. The design and synthesis of highly conductive and durable alkaline membranes/ionomers have enabled AEMFCs to reach initial performance metrics equal to or higher than those of PEMFCs. We emphasize the importance of using membrane electrode assemblies (MEAs) to integrate the often separately pursued/optimized electrocatalyst/support and membranes/ionomer components. Operando/in situ methods, at multiscales, and ab initio simulations provide a mechanistic understanding of electron, ion, and mass transport at catalyst/ionomer/membrane interfaces and the necessary guidance to achieve fuel cell operation in air over thousands of hours. We hope that this Review will serve as a roadmap for advancing the scientific understanding of the fundamental factors governing electrochemical energy conversion in alkaline media with the ultimate goal of achieving ultralow Pt or precious-metal-free high-performance and durable alkaline fuel cells and related technologies.

Electrocatalysis has been the cornerstone for enhancing energy efficiency, minimizing environmental impacts and carbon emissions, and enabling a more sustainable way of meeting global energy needs. Elucidating the structure and reaction mechanisms of electrocatalysts at electrode-electrolyte interfaces is fundamental for advancing renewable energy technologies, including fuel cells, water electrolyzers, CO2 reduction, and batteries, among others. One of the fundamental challenges in electrocatalysis is understanding how to activate and sustain electrocatalytic activity, under operating conditions, for extended time periods and with optimal activity and selectivity. Although traditional ex situ methods have provided a baseline understanding of heterogeneous (electro)catalysts, they cannot provide real-time interfacial structural and compositional changes under reaction conditions, which calls for the use of in situ/operando methods. Herein, we provide a selective review of in situ and operando characterizations, in particular, the use of operando synchrotron-based X-ray techniques and in situ atomic-scale scanning transmission electron microscopy (STEM) in liquid/gas phases to advance our understanding of electrode-electrolyte interfaces at macro- and microscopic levels, which dictate the charge transfer kinetics and overall reaction mechanisms. The use of scanning electrochemical microscopy (SECM) enables direct probing of the local activity of electrocatalysts at the nanometer scale. In addition, differential electrochemical mass spectrometry (DEMS) and the electrochemical quartz crystal balance (EQCM) enable the simultaneous identification of multiple reaction intermediates and products for mechanistic studies of electrocatalyst selectivity and durability. We anticipate that continuous advances of in situ/operando techniques and probes will continue to make significant contributions to establishing structure/composition-reactivity correlations of electrocatalysts at unprecedented atomic-scale and molecular levels under realistic, real-time reaction conditions.

Although the concept, first demonstration, and potential applications of X-ray transmission mirrors (XTMs) were initially described over 30 years ago, only a few implementations exist in the literature. This is attributed to the unsolved challenge of a thick frame supporting a thin, reflecting membrane which does not itself block the transmitted beam. Here, we introduce a novel approach to solve this problem by employing silicon microfabrication. A robust XTM frame has been fabricated by using a novel two-step etch process, which secures the thin-film membrane without blocking the transmitted beam. Specifically, we have fabricated delicate XTM optics with 90% yield, which consist of 280-nm-thick low-stress silicon nitride membrane windows that are 1.5 mm wide and 125 mm long on silicon substrates. The XTM optics have been demonstrated to be a more efficient high-pass X-ray filter; for example, when configured for 40% transmission of 11.3 keV photons, we measure the reduction of 8.4 keV photons by a factor of 56.

CHESS, the Cornell High Energy Synchrotron Source, is a high-intensity X-ray source located on the Cornell University Ithaca campus. Since its inception in 1980, CHESS has been a leader in the prod...

Although Li metal has long been considered to be the ideal anode material for Li rechargeable batteries, our limited understanding of the complex mechanism of Li plating has hindered the widespread deployment of Li metal anodes. Therefore, operando studies are required to unambiguously reveal the complex mechanistic steps involved. In this study, we employed synchrotron-based X-ray imaging methods to visualize the evolution of Li plating/stripping under operando and, more importantly, practical conditions for battery operation, providing detailed insights into morphology evolution during Li plating. The effects of critical battery operating parameters, including concentration of Li salts, current density, ionic strength, and various electrolytes and additives, on Li plating/stripping have been studied. The delicate interplay of these conditions on the resulting Li metal morphology has been characterized for the first time.

We have developed an improved method of time-resolved x-ray reflectivity (XRR) using monochromatic synchrotron radiation. Our method utilizes a polycapillary x-ray optic to create a range of incident angles and an area detector to collect specular reflections. By rotating the sample normal out of the plane of the incident fan, we can separate the surface diffuse scatter from the reflectivity signal, greatly improving the quality of the XRR spectra compared to previous implementations. We demonstrate the time-resolved capabilities of this system, with the temporal resolution as low as 10 ms, by measuring XRR during the annealing of Al/Ni nano-scale multilayers, and use this information to extract the activation energy for interdiffusion in this system.

Yao Yang, Yin Xiong, Elliot Padgett, Howie Joress, Venkata Yarlagadda, Anusorn Kongkanand, Joel D. Brock, Francis J. DiSalvo, Héctor D. Abruña, David. A. Muller.* 1. Department of Chemistry and Chemical Biology, Cornell University, Ithaca, NY 14853, USA. 2. School of Applied and Engineering Physics, Cornell University, Ithaca, NY 14853, USA. 3. Cornell High Energy Synchrotron Source, Cornell University, Ithaca, NY 14853, USA. 4. Fuel Cell R&D, General Motors Global Propulsion Systems, Pontiac, MI 48340, USA. *Corresponding author: dm24@cornell.edu

The structural perfection and defect microstructure of epitaxial (001) $\mathrm{SrTi}{\mathrm{O}}_{3}$ films grown on (001) Si was assessed by a combination of x-ray diffraction and scanning transmission electron microscopy. Conditions were identified that yield 002 $\mathrm{SrTi}{\mathrm{O}}_{3}$ rocking curves with full width at half-maximum below 0.03\ifmmode^\circ\else\textdegree\fi{} for films ranging from 2 to 300 nm thick, but this is because this particular peak is insensitive to the $\ensuremath{\sim}8\ifmmode\times\else\texttimes\fi{}{10}^{11}\phantom{\rule{0.16em}{0ex}}\mathrm{c}{\mathrm{m}}^{--2}$ density of threading dislocations with pure edge character and extended defects containing dislocations and out-of-phase boundaries. Our results show that one narrow rocking curve peak is insufficient to characterize the structural perfection of epitaxial films.

Ordered intermetallic nanoparticles are promising electrocatalysts with enhanced activity and durability for the oxygen-reduction reaction (ORR) in proton-exchange membrane fuel cells (PEMFCs). The ordered phase is generally identified based on the existence of superlattice ordering peaks in powder X-ray diffraction (PXRD). However, after employing a widely used postsynthesis annealing treatment, we have found that claims of "ordered" catalysts were possibly/likely mixed phases of ordered intermetallics and disordered solid solutions. Here, we employed in situ heating, synchrotron-based, X-ray diffraction to quantitatively investigate the impact of a variety of annealing conditions on the degree of ordering of large ensembles of Pt3Co nanoparticles. Monte Carlo simulations suggest that Pt3Co nanoparticles have a lower order-disorder phase transition (ODPT) temperature relative to the bulk counterpart. Furthermore, we employed microscopic-level in situ heating electron microscopy to directly visualize the morphological changes and the formation of both fully and partially ordered nanoparticles at the atomic scale. In general, a higher degree of ordering leads to more active and durable electrocatalysts. The annealed Pt3Co/C with an optimal degree of ordering exhibited significantly enhanced durability, relative to the disordered counterpart, in practical membrane electrode assembly (MEA) measurements. The results highlight the importance of understanding the annealing process to maximize the degree of ordering in intermetallics to optimize electrocatalytic activity.

Identifying the catalytically active site(s) in the oxygen reduction reaction (ORR), under real-time electrochemical conditions, is critical to the development of fuel cells and other technologies. We have employed in situ synchrotron-based X-ray absorption spectroscopy (XAS) to investigate the synergistic interaction of a Co-Mn oxide catalyst which exhibits impressive ORR activity in alkaline fuel cells. X-ray absorption near edge structure (XANES) was used to track the dynamic structural changes of Co and Mn under both steady state (constant applied potential) and nonsteady state (potentiodynamic cyclic voltammetry, CV). Under steady state conditions, both Mn and Co valences decreased at lower potentials, indicating the conversion from Mn(III,IV) and Co(III) to Mn(II,III) and Co(II), respectively. Rapid X-ray data acquisition, combined with a slow sweep rate in CV, enabled a 3 mV resolution in the applied potential, approaching a nonsteady (potentiodynamic) state. Changes in the Co and Mn valence states were simultaneous and exhibited periodic patterns that tracked the cyclic potential sweeps. To the best of our knowledge, this represents the first study, using in situ XAS, to resolve the synergistic catalytic mechanism of a bimetallic oxide. Strategies developed/described herein can provide a promising approach to unveil the reaction mechanism for other multimetallic electrocatalysts.

High quality, epitaxial thin-films are key components of almost all modern electronic devices. During deposition, lattice mismatch between the substrate and the film generates elastic strain. The strain energy grows with film thickness until a defect is generated that relieves the strain. The strain relaxation mechanism is critical in epitaxial electrodeposition. Here, we study how a metal (bismuth) film growing via electrodeposition on a semiconductor substrate [GaAs(110)] relaxes the lattice mismatch-induced strain. Using in situ synchrotron-based X-ray techniques, we monitor the crystallographic orientation and grain size of the growing film during electrochemical deposition. We (1) confirm that a single crystallographic orientation of the film, with (011¯8) as the oriented plane, can be selected by controlling the overpotential, η, and (2) find that, after a threshold thickness is reached, the tilt angle varies monotonically with film thickness. Our data are consistent with the film relaxing the strain by forming low-energy, asymmetric tilt boundaries.

Sodium-ion batteries have been considered as one of the most promising types of batteries, beyond lithium-ion batteries, for large-scale energy storage applications. However, their deployment hinges on the development of new anode materials, since it has been shown that many important anode materials employed in lithium ion batteries, such as graphite and silicon, are inadequate for sodium-ion batteries. We have simply prepared novel SnS/C nanocomposites through a top-down approach as anode materials for sodium-ion batteries. Their electrochemical performance has been significantly improved when compared to bare SnS, especially in terms of cycling stability and rate capabilities. SnS/C nanocomposites exhibit excellent capacity retention, at various current rates, and deliver capacities as high as 400 mA h g-1 even at the high current density of 800 mA g-1 (2C). Ex situ transmission electron microscopy, X-ray diffraction and operando X-ray absorption near edge structure studies have been performed in order to unravel the reaction mechanism of the SnS/C nanocomposites.

There is a great deal of interest in developing battery systems that can exhibit self-healing behavior, thus enhancing cyclability and stability. Given that gallium (Ga) is a metal that melts near room temperature, we wanted to test if it could be employed as a self-healing anode material for lithium-ion batteries (LIBs). However, Ga nanoparticles (NPs), when directly applied, tended to aggregate upon charge/discharge cycling. To address this issue, we employed carbon-coated Ga2O3 NPs as an alternative. By controlling the pH of the precursor solution, highly dispersed and ultrafine Ga2O3 NPs, embedded in carbon shells, could be synthesized through a hydrothermal carbonization method. The particle size of the Ga2O3 NPs was 2.6 nm, with an extremely narrow size distribution, as determined by high-resolution transmission electron microscopy and Brunauer-Emmett-Teller measurements. A lithium-ion battery anode based on this material exhibited stable charging and discharging, with a capacity of 721 mAh/g after 200 cycles. The high cyclability is due to not only the protective effects of the carbon shell but also the formation of Ga0 during the lithiation process, as indicated by operando X-ray absorption near-edge spectroscopy.

A new technique for the parallel collection of X-ray reflectivity (XRR) data, compatible with monochromatic synchrotron radiation and flat substrates, is described and applied to the in situ observation of thin-film growth. The method employs a polycapillary X-ray optic to produce a converging fan of radiation, incident onto a sample surface, and an area detector to simultaneously collect the XRR signal over an angular range matching that of the incident fan. Factors determining the range and instrumental resolution of the technique in reciprocal space, in addition to the signal-to-background ratio, are described in detail. This particular implementation records ∼5° in 2θ and resolves Kiessig fringes from samples with layer thicknesses ranging from 3 to 76 nm. The value of this approach is illustrated by showing in situ XRR data obtained with 100 ms time resolution during the growth of epitaxial La0.7Sr0.3MnO3 on SrTiO3 by pulsed laser deposition at the Cornell High Energy Synchrotron Source (CHESS). Compared with prior methods for parallel XRR data collection, this is the first method that is both sample-independent and compatible with the highly collimated, monochromatic radiation typical of third-generation synchrotron sources. Further, this technique can be readily adapted for use with laboratory-based sources.

With over 60 facilities located around the world, storage ring x-ray sources have become key components in the scientific toolbox of diverse research specialties and communities.Both upgrades to existing sources and brand new facilities are currently pushing the quality of the x-ray beams towards the fundamental (diffraction) limit for size and collimation imposed by the wave nature of electromagnetic radiation.At the same time, flux, stability, wavelength and reliability all continue to improve significantly.Furthermore, new detector technologies, x-ray optics, sample environments, and data collection strategies have significantly enhanced experimental capabilities and promise even greater things to come.In this review of storage ring x-ray sources, I will briefly review the history of storage ring x-ray sources and then point out some of the new developments and the opportunities they will create for researchers.

As the need for the development of "beyond lithium" ion battery technologies continuous unabated, lithium sulfur batteries have attracted widespread attention due to their very high theoretical energy density of 2,600 Wh kg-1. However, despite much effort, the detailed reaction mechanism remains poorly understood. In this study, we have combined operando X-ray diffraction and X-ray microscopy along with X-ray tomography, to visualize the evolution of both the morphology and crystal structure of the materials during the entire battery cycling (discharging/charging) process. The dissolution and reformation of sulfur clusters is clearly observed during cycling. In addition, we demonstrate, for the first time, the critical role of current density and temperature in determining the size of both the resulting sulfur clusters and Li2S particles. This study provides new insights about promising avenues for the continued development of lithium sulfur batteries, which we believe may lead to their broad deployment and application.

A major goal of energy research is to use visible light to cleave water directly, without an applied voltage, into hydrogen and oxygen. Although SrTiO3 requires ultraviolet light, after four decades, it is still the "gold standard" for the photo-catalytic splitting of water. It is chemically robust and can carry out both hydrogen and oxygen evolution reactions without an applied bias. While ultrahigh vacuum surface science techniques have provided useful insights, we still know relatively little about the structure of these electrodes in contact with electrolytes under operating conditions. Here, we report the surface structure evolution of a n-SrTiO3 electrode during water splitting, before and after "training" with an applied positive bias. Operando high-energy X-ray reflectivity measurements demonstrate that training the electrode irreversibly reorders the surface. Scanning electrochemical microscopy at open circuit correlates this training with a 3-fold increase of the activity toward the photo-induced water splitting. A novel first-principles joint density functional theory simulation, constrained to the X-ray data via a generalized penalty function, identifies an anatase-like structure as the more active, trained surface.