Elucidating dielectric losses, structural heterogeneity, and interface imperfections is critical for improving coherence in superconducting qubits. However, most diagnostics rely on destructive electron microscopy or low-throughput millikelvin quantum measurements. Here, we demonstrate noninvasive terahertz (THz) nano-imaging/-spectroscopy of encapsulated niobium transmon qubits, revealing sidewall near-field scattering that correlates with qubit coherence. We further employ a THz hyperspectral line scan to probe dielectric responses and field participation at Al junction interfaces. These findings highlight the promise of THz near-field methods as a high-throughput proxy characterization tool for guiding material selection and optimizing processing protocols to improve qubit and quantum circuit performance.

Fe−6.5%Si has higher electrical resistivity, lower magnetocrystalline anisotropy, and lower magnetostriction than traditional Fe−3.2%Si silicon steel. The reduced iron losses of Fe−6.5%Si render it a highly favorable candidate for high-speed motors and transformers. However, large-scale production of wide Fe−6.5%Si tape by rapid solidification can be challenging mainly because of its high melting point. In this work, boron is alloyed to Fe−6.5%Si to reduce its melting temperature and interfacial energy to improve the alloy’s processability. Boron additions from 0.01 wt.% to 2.24 wt.% into Fe−6.5%Si and its effect on ribbon thickness, grain size, magnetic, and mechanical properties were studied. Minor boron alloying significantly changed the melt pool stability and wetting on the quench wheel and in turn increased the quench rate with minimum impact on the magnetic saturation and ductility. Boron addition of < 0.06 wt.% was also found beneficial to the magnetic property of the alloy by lowering both its hysteresis and eddy current losses.

We present a novel transmon qubit fabrication technique that yields systematic improvements in T$_1$ relaxation times. We fabricate devices using an encapsulation strategy that involves passivating the surface of niobium and thereby preventing the formation of its lossy surface oxide. By maintaining the same superconducting metal and only varying the surface structure, this comparative investigation examining different capping materials, such as tantalum, aluminum, titanium nitride, and gold, and film substrates across different qubit foundries definitively demonstrates the detrimental impact that niobium oxides have on the coherence times of superconducting qubits, compared to native oxides of tantalum, aluminum or titanium nitride. Our surface-encapsulated niobium qubit devices exhibit T$_1$ relaxation times 2 to 5 times longer than baseline niobium qubit devices with native niobium oxides. When capping niobium with tantalum, we obtain median qubit lifetimes above 300 microseconds, with maximum values up to 600 microseconds, that represent the highest lifetimes to date for superconducting qubits prepared on both sapphire and silicon. Our comparative structural and chemical analysis suggests why amorphous niobium oxides may induce higher losses compared to other amorphous oxides. These results are in line with high-accuracy measurements of the niobium oxide loss tangent obtained with ultra-high Q superconducting radiofrequency (SRF) cavities. This new surface encapsulation strategy enables even further reduction of dielectric losses via passivation with ambient-stable materials, while preserving fabrication and scalable manufacturability thanks to the compatibility with silicon processes.

Nickel-based superalloys are in great demand for harsh-service conditions involving high temperatures and oxidative environments. Haynes 282 stands out due to its excellent high-temperature properties and easy fabricability. However, the upper usage temperature of Haynes 282 is limited due to its relatively low liquidus temperature. Through high-fidelity density functional theory calculations and high-throughput experiments, new compositions that show higher liquidus temperature and higher strength are explored. While maintaining processability, the newly designed alloy shows improved strength and ductility at room temperature and better oxidation resistance up to 800°C. The new compositions showcase a minor change in the refractory and metalloid content can have a significant impact on the mechanical and oxidation performance of superalloys.

Dy-free sintered magnets were fabricated by blending Neo powder with different grain boundary diffusion alloy powders. Cu, CeAl and CeAlCu have a negative effect on H cj of magnets, while PrAlCu and AlCuGa have a positive effect. The PrAlCu-added magnet achieves the best magnetic properties among all magnets with the additions of different diffusion alloys. With increasing PrAlCu from 0-10 wt.%, H cj of the magnets gradually increases from the original 14.5 kOe to 19.2 kOe. The magnet with 7.5 wt.% PrAlCu obtains a H cj of 18 kOe and (BH) max of 39.1 MGOe. It is found that Pr and Cu in PrAlCu alloy is mainly distributed at grain boundary and triple junctions, leading to a reduced coupling among grains, thus an enhanced H cj . The grain boundary engineering by adding an appropriate alloy is an effective method to improve H cj of Dy-free NdFeB magnets.

Superconducting quantum circuits (SQC) are one of the most promising hardware platforms for quantum computing, yet their performance is currently limited by the presence of various structural defects inside the circuit's structure. Despite impressive progress in the past decade, a precise understanding of the origin of these defects from various fabrication processes and their impact on coherence is still lacking. In this study, we performed a comprehensive investigation on the microstructure, superconductivity, and resonator quality factor of Nb films deposited by high-power impulse magnetron sputtering (HiPIMS) and direct current (DC) magnetron sputtering. A suite of characterization techniques, including electron microscopy with spectroscopy, secondary ion mass spectrometry, magneto-optical microscopy, and pump-probe reflectivity spectroscopy is used. We reveal that niobium (Nb) resonators fabricated using HiPIMS exhibit a smaller average grain size, thicker surface oxide with larger thickness variations (rougher surface), and a thicker amorphous Nb/Si interface layer compared to samples deposited by DC sputtering. We identified that the amorphous Nb oxides (mainly located at the Nb surface and along the grain boundaries) and Nb-Si amorphous layers (at the Nb/Si interface) are major and potential sources of two-level system (TLS), while off-stochiometric oxides and suboxides of Nb close to the surface, crystalline defects (i.e., dislocations at grain boundary, point defects introduced during deposition) are main contributors of non-TLS sources. Our findings clarify the relationship between different defects and coherence loss mechanisms, highlighting the importance of material microstructure control on performance optimization in SQC.

We investigate the effect of an applied magnetic field on the entire HDDR process using a customized reactor vessel and a warm-bore superconducting magnet. We analyzed the resulting properties produced at both a 0 applied field and a 2 Tesla applied field. We show that the application of a magnetic field throughout the HDDR process results in powders that exhibit a greater level of anisotropy compared to their ambient field counterparts.

In this work, we have used bulk combinatorial synthesis to rapidly identify a (Nd,Ce,La)-Fe-B composition that is both Nd-lean (<50 % of total rare earth content) and exhibits good thermal stability (TC similar to 269 degrees C). Bulk anisotropic magnets of the corresponding composition [i.e. (Nd0.47Ce0.28La0.25)(2.2)Fe14B1 (at%) + (1.5 wt% TiC)] were synthesized by hot deformation and hot-roll processes. To enhance the energy product of the hot deformed alloys, feedstock powder with 2.5-7.5 wt% Ce-Al-Cu grain boundary modifier was blended together prior to deformation processing. Moreover, hot deformation processing parameters, temperature (T), and processing time (t), were examined over a wide range to enhance the energy product of the resultant magnet alloys. We found that adding just 2.5 wt% Ce-Al-Cu increased the maximum energy product from similar to 12 MGOe for the monolithic alloy to similar to 20 MGOe for the alloy with added grain bounder modifier. The processing parameters (e.g., temperature and time) identified for hot deformation were applied to the hot-rolling process to synthesize samples with larger dimensions that exhibit an energy product of 17.7 MGOe with 5 wt% Ce-Al-Cu added.

Superconducting quantum bits (qubits) rely on ultra-thin, amorphous oxide tunneling barriers that can have significant inhomogeneities and defects as grown. This can result in relatively large uncertainties and deleterious effects in the circuits, limiting the scalability. Finding a robust solution to the junction reproducibility problem has been a long-standing goal in the field. Here, we demonstrate a transformational technique for controllably tuning the electrical properties of aluminum-oxide tunnel junctions. This is accomplished using a low-voltage, alternating-bias applied individually to the tunnel junctions, with which resistance tuning by more than 70% can be achieved. The data indicates an improvement of coherence and reduction of two-level system defects. Transmission electron microscopy shows that the treated junctions are predominantly amorphous, albeit with a more uniform distribution of alumina coordination across the barrier. This technique is expected to be useful for other devices based on ionic amorphous materials. Amorphous aluminum oxide tunnel junctions are important for cryogenic and room temperature devices. Here, the authors demonstrate the use of alternating-bias-assisted annealing for transforming and tuning transmon qubit junctions, where giant increases in excess of 70% in the room temperature resistance can be achieved.

The addition of Zn to AlCrFeCoNi high-entropy alloy (HEA) poses intriguing questions as to how it would affect phase evolution. Herein, the phase evolution in AlCrFeCoNiZn is studied using a combination of experimental techniques (X-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, and differential scanning calorimetry) and computational (density-functional theory [DFT], calculation of phase diagrams, and machine-learning) methods. Mechanically alloyed and spark-plasma-sintered AlCrFeCoNiZn assumes a metastable single-phase, body-centered-cubic (BCC) structure that undergoes diffusion-controlled phase separation upon subsequent heat treatment to form separate (Al, Cr)-rich, (Fe, Co)-rich, and (Zn, Ni)-rich phases. The formation of (Al, Cr)-rich phase, not reported previously in AlCrFeCoNi-based HEAs, is attributed to strong clustering tendency of Cr-Zn and Cr-Ni pairs, combined with the strong ordering of Zn-Ni pair, driving out Cr that in turn combines with Al to form a (Al, Cr)-rich phase. In the DFT results, the formation of thermodynamically stable L12 phase is shown wherein Cr-Fe-Zn [Al-Ni-Co] preferably occupy1a (000) [3c (0 1/2 1/2)] positions. The sluggish diffusional transformation to L12 phase from BCC precursors is attributed to the small stacking-fault energy of AlCrFeCoNiZn. The equilibrated HEA exhibits a high microhardness of 8.24 GPa with an elastic modulus of 184 GPa. In this work, the addition of Zn to AlCrFeCoNi high-entropy alloy is probed. The formation of an (Al, Cr)-rich phase is observed, owing to the large ordering tendency of the Al-Ni pair that results in the formation of (Al, Ni)-rich phases. The Zn addition drives new ordering and clustering behavior, which results in phase separation.image (c) 2024 WILEY-VCH GmbH

London penetration depth was measured in niobium foils, thin films, single crystals, and superconducting radio-frequency (SRF) cavity pieces cut out from different places. The low-temperature (T<Tc/3) variation, sensitive to the low-energy quasiparticles with states inside the superconducting gap, differs dramatically between different types of samples. With the help of phenomenological modeling, we correlate these different behaviors with known pair-breaking mechanisms and show that such measurements may help distinguish between different pair-breaking mechanisms, such as niobium hydrides and two-level systems (TLS). The conclusions also apply to SRF cavities when tracking the temperature-dependent quality factor and the resonant frequency.

The effect of annealing on the superconducting properties of niobium single crystals cut from the same master boule was studied by local and global magnetic measurements, as well as scanning tunneling microscopy (STM). The formation of large hydride precipitates was observed in unannealed samples. The variation in structural and magnetic properties was studied after annealing under high vacuum at 800 C, 1400 C, and near the melting point of niobium (2477 C) for a few seconds. The initial samples had a high hydrogen content. Polarized optics and magneto-optical studies show that the formation of large niobium hydride precipitates is suppressed already by 800 C annealing. However, the overall superconducting properties in the annealed samples did not improve after annealing, and in fact, worsened. The superconducting transition temperature decreased, the upper critical field increased, and the pinning strength increased. Parallel studies were conducted using STM, where the sample was annealed initially at 400 C, measured, annealed again at 1700 C, and measured again. These studies revealed a ``dirty'' superconducting gap with a significant spatial variation of tunneling conductance after annealing at 400 C. The clean gap was recovered after annealing at 1700 C. It is likely that these results are due to oxygen redistribution near the surface, which is always covered by oxide layers in as-grown crystals. Overall, the results indicate that vacuum annealing at least up to 1400 C, while expected to remove a large amount of hydrogen, introduces additional nanosized defects, perhaps hydride precipitates, that act as efficient pair-breaking and pinning centers.

Nanoscale structural and electronic heterogeneities are prevalent in condensed matter physics. Investigating these heterogeneities in 3D has become an important task for understanding material properties. To provide a tool to unravel the connection between nanoscale heterogeneity and macroscopic emergent properties in magnetic materials, scanning transmission X-ray microscopy (STXM) is combined with X-ray magnetic circular dichroism. A vector tomography algorithm has been developed to reconstruct the full 3D magnetic vector field without any prior noise assumptions or knowledge about the sample. Two tomographic scans around the vertical axis are acquired on single-crystalline Nd2Fe14B pillars tilted at two different angles, with 2D STXM projections recorded using a focused 120 nm X-ray beam with left and right circular polarization. Image alignment and iterative registration have been implemented based on the 2D STXM projections for the two tilts. Dichroic projections obtained from difference images are used for the tomographic reconstruction to obtain the 3D magnetization distribution at the nanoscale.

Nickel-based superalloys are in great demand for harsh-service conditions involving high temperatures and oxidative environments. Haynes 282 stands out due to its excellent high-temperature properties and easy fabricability. However, the upper operation temperature of Haynes 282 is limited due to its relatively low liquidus temperature. Equipped with high-fidelity density-functional theory calculations and high-throughput experimentation methodology, we explored new compositional spaces that exhibit higher liquidus temperature and higher strength. While maintaining the manufacturability, the newly designed alloy shows improved strength and ductility at room temperature and better oxidation resistance up to 800°C. The new compositions showcase a minor change in the refractory and metalloid content can significantly impact the mechanical and oxidation performance of superalloys.

The performance of superconducting qubits is often limited by dissipation and two-level systems ( TLS) losses. The dominant sources of these losses are believed to originate from amorphous materials and defects at interfaces and surfaces, likely as a result of fabrication processes or ambient exposure. Here, we explore a novel wet chemical surface treatment at the Josephson junction-substrate and the substrate-air interfaces by replacing a buffered oxide etch (BOE) cleaning process with one that uses hydrofluoric acid followed by aqueous ammonium fluoride. We show that the ammonium fluoride etch process results in a statistically significant improvement in median T-1 by similar to 22% (p = 0.002), and a reduction in the number of strongly-coupled TLS in the tunable frequency range. Microwave resonator measurements on samples treated with the ammonium fluoride etch after niobium deposition and etching also show similar to 33% lower TLS-induced loss tangent compared to the BOE treated samples. As the chemical treatment primarily modifies the Josephson junction-substrate interface and substrate-air interface, we perform targeted chemical and structural characterizations to examine materials differences at these interfaces and identify multiple microscopic changes that could contribute to decreased TLS losses.

Dy-free sintered magnets were fabricated by blending Neo powder with different amount of PrCu powder. With increasing PrCu from 0-10 wt.%, Hcj of the magnets gradually increases from the original 14.5 kOe to 18.6 kOe. The highest (BH)max achieved was 35.0 MGOe with 7.5 wt.% PrCu. It was found that PrCu was mainly distributed at grain boundary and triple junctions, leading to a reduced coupling among grains, thus an enhanced Hcj. The grain boundary engineering by the diffusion of PrCu alloy is an effective method to improve Hcj of Dy-free magnets.

Multi-principal-element alloys (also known as medium and high entropy alloys) offer a much larger and richer design space than conventional alloys, providing opportunities for discovering new functionalities and their governing physics. Some of these alloys exhibit an outstanding combination of high strength and ductility, linked to the activation of various deformation modes triggered by low-energy stacking faults. However, a pressing question remains: Is the plasticity of medium- and high-entropy alloys governed only by stacking fault energy, or does atomic short-range order (SRO) play a role? To answer this, we investigated how SRO affects the deformation in single-crystalline NiCoCr, with previous contradictory findings. First, we established unique experimental evidence for SRO formation in bulk single crystals using high-energy synchrotron transmission X-Ray Diffraction. By tuning the degree of SRO by aging at high temperatures, twinning density and strain-induced martensitic phase transformation can be significantly increased in the [110] and [111] orientations under tension, increasing the tensile ductility; yet, no increase was observed along the [001] orientation due to lack of TWinning-Induced Plasticity (TWIP) or TRansformation-Induced Plasticity (TRIP), indicating a strong crystallographic orientation dependence. Our first-principles thermodynamic calculations unequivocally show SRO exists and governs the observed microstructural evolution and deformation hardening behavior. Here we find direct proof that SRO triggers a simultaneous TWIP and TRIP in NiCoCr, a rare microstructural evolution path. Our findings establish that the interplay of SRO and plasticity could be exploited to alter deformation modes and yield unprecedented mechanical response in medium- and high-entropy alloys.

Fe−6.5

Niobium thin films on silicon substrate used in the fabrication of superconducting qubits have been characterized using scanning and transmission electron microscopy, electrical transport, magnetization, quasiparticle spectroscopy, and real-space real-time magneto-optical imaging. We study niobium films to provide an example of a comprehensive analytical set that may benefit superconducting circuits such as those used in quantum computers. The films show outstanding superconducting transition temperature of T_c=9.35 K and a fairly clean superconducting gap, along with superfluid density enhanced at intermediate temperatures. These observations are consistent with the recent theory of anisotropic strong-coupling superconductivity in Nb. However, the response to the magnetic field is complicated, exhibiting significantly irreversible behavior and insufficient heat conductance leading to thermo-magnetic instabilities. These may present an issue for further improvement of transmon quantum coherence. Possible mitigation strategies are discussed.

Refractory multi-principal-element alloys (RMPEAs) exhibit high specific strength at elevated temperatures ( T ). However, current RMPEAs lack a balance of room-temperature (RT) ductility, high- T strength, and high- T creep resistance. Using density-functional theory methods, we scanned composition space using four criteria: (1) formation energies for operational stability: -150≤E_f ≤ +70 meV per atom; (2) higher strength found via interstitial electron density with Young’s moduli E > 250 GPa; (3) inverse Pugh ratio for ductility: G / B < 0.57; and (4) high melting points: T m > 2500 °C. Using rapid bulk alloy synthesis and characterization, we validated theory and down-selected promising alloy compositions and discovered Mo 72.3 W 12.8 Ta 10.0 Ti 2.5 Zr 2.5 having well-balanced RT and high- T mechanical properties. This alloy has comparable high- T compressive strength to well-known MoNbTaW but is more ductile and more creep resistant. It is also superior to a commercial Mo-based refractory alloy and a nickel-based superalloy (Haynes-282) with improved high- T tensile strength and creep resistance.