Bio-based adhesives offer inherent advantages over conventional petrochemical-derived systems, including renewable sourcing, reduced environmental impact and potential degradability. However, most bio-based adhesives suffer from poor adhesion strength, limited substrate compatibility and a lack of chemical recyclability. Here we present a bio-derived multiblock poly(ester amide) adhesive that leverages microphase segregation between different segments to reconcile mechanical robustness with strong interfacial bonding. Notably, this multiblock architecture is accessed through a one-pot, selective acceptorless dehydrogenative polymerization, obviating the need for multistep synthesis. The materials exhibit excellent adhesion across a range of substrates including metals, glass and wet wood surpassing commercial benchmarks, while also demonstrating thermal stability, tunable mechanical properties and closed-loop chemical recyclability even in the presence of other commodity plastics. Furthermore, the adhesive strength of these materials could be tuned for various potential applications through control over the chemical composition of the polymer. By integrating renewable feedstocks, high-performance functionality and efficient chemical circularity within a single platform, this work provides a viable pathway toward more sustainable adhesive technologies and contributes to advancing circular materials manufacturing.

Abstract Semicrystalline polymers, e.g., polyethylene terephthalate (PET), release micro- (100 nm to 1 mm) and nanoplastics (up to 100 nm) [MNPL] when they are degraded under quiescent conditions. However, the exact molecular mechanisms leading to material fragmentation into MNPL are unknown. Here, we monitor the evolution of chain molecular weight and the MNPL production kinetics during hydrolysis of PET pellets. We find that only ≈0.6% of the amorphous phase ester bonds are hydrolyzed at the onset of MNPL release. Then, by combining a random scission model with measured amorphous spacings, we estimate that only ≈15% of the stress transmitters in the amorphous phase, namely, bridges and entangled loops, have failed by this point. Thus, spontaneous fragmentation of the semicrystalline nanostructure occurs despite significant intercrystalline connectivity. We resolve this apparent contradiction by proposing that fragmentation can only occur when progressive tie-chain scission causes the material to undergo the ductile/brittle transition. Mechanistically, we speculate that the internal stresses responsible for material fragmentation are caused by processing (i.e., residual stresses) and/or sample densification induced by chemi-crystallization. We discuss additional factors that may affect our analysis and thus require further investigation, such as skin-core effects, preferential degradation of stress transmitters and/or recrystallization processes.

ABSTRACT Seeking recyclable, more sustainable alternatives to nylon 6 has drawn much attention, but achieving its variants with both crystallinity and enhanced recyclability still remains a challenge. Here, by utilizing bio‐derivable mono‐substituted racemic lactam monomers, we reveal surprisingly large effects of methyl substitution positions on the nylon‐6 backbone on crystallizability, thermomechanical performance, and recyclability of the resulting atactic nylon‐6 variants. While γ‐methyl substitution gives an amorphous nylon, all other four methyl‐substitution positions (α, β, δ, and ε) afford, unexpectedly, crystalline nylons with melting temperatures ranging from 145°C to 200°C and tunable mechanical performance from being stiff and strong (α, ε) to ductile (β, δ). Investigations reveal that the crystallinity of atactic nylons arises independently of stereoregularity, which is driven by the amide backbone with robust hydrogen‐bonding interactions and countered by the chain flexibility regulated by the substitution position. These nylons can be chemically recycled back to their parent monomers with high isolated yields up to 92%, enabling a circular, tacticity‐independent crystalline nylon platform.

Polyhydroxyalkanoates (PHAs) are versatile, biobased polyesters that are often targeted for use as degradable thermoplastic replacements for polyolefins. Given the substantial chemical diversity of PHA, their potential as cross-linked polymers could also enable similar platforms for reversible, degradable thermosets. In this work, we genetically engineered Pseudomonas putida KT2440 to synthesize poly(3-hydroxybutyrate-co-3-hydroxyundecenoate) (PHBU), which contains both 3-hydroxybutyrate and unsaturated 3-hydroxyundecenoate components. To reduce the brittleness of this polymer, we physically blended PHBU with the soft copolymer poly(3-hydroxydecanonate-co-3-hydroxyundecenoate) in mass ratios of 1:3, 1:1, and 3:1. Upon observing varying degrees of immiscibility by scanning electron microscopy, we installed dynamic boronic ester cross-links via thiol-ene click chemistry, which resulted in compatibilized dynamic thermoset blends ranging in hard, medium, and soft rubber or elastomer thermomechanical profiles. These dynamic thermoset blends were subjected to controlled biological degradation experiments in freshwater conditions, achieving timely mass loss despite the cross-linked architectures. Overall, this work highlights a two-component platform for the production of degradable and reprocessable dynamic thermoset blends suitable for several classes of cross-linked polymer technologies from tailored, biological PHA copolymers.

Lignin-derived aromatic carboxylic acids can be produced from oxidative catalytic processes and are promising building blocks for performance-advantaged bioproducts that leverage their inherent heteroatom functionalities. Here, we synthesize 2-methoxyterephthalate and 2,6-dimethoxyterephthalate derivatives by electrochemical carboxylation of guaiacyl- and syringyl-derived lignin monomers obtained from the oxidative deconstruction of lignin. These methoxylated terephthalates are evaluated as co monomers in poly(ethylene terephthalate) (PET) and as plasticizers that could replace petrochemically derived isophthalate and phthalate, respectively. Specifically, we co-polymerize 2-methoxy- and 2,6 dimethoxyterephthalate with dimethyl terephthalate to form several PET co-polymers, both of which enable the properties of PET to be tuned, with an incorporation beyond 25% producing amorphous polyesters. At 10 mol% loading in the co-polymers, we demonstrate that the bio-derived co-monomers exhibit comparable behavior to isophthalic acid, a commonly used co-monomer in PET, by lowering the crystallinity and melting temperature. Moreover, methoxyterephthalate esters (2-ethyl hexyl and butyl) are compared to phthalate and terephthalate ester counterparts used as poly(vinyl chloride) (PVC) plasticizers. The bio derived plasticizers are comparable to the petroleum-derived incumbents in reducing the glass transition temperature and increasing the thermal stability of PVC. Furthermore, the dimethoxyterephthalic esters are expected to have an extended lifetime in the polymer matrix, due to their lower volatility and by lower diffusion coefficients calculated by molecular dynamic simulations. These results demonstrate that the isophthalate and phthalate components in polyesters and plasticizers, respectively, could be substituted with bio-based methoxyterephthalate derivatives.

Biobased furanic polyesters can exhibit performance advantages over petroleum-derived polyesters, primarily due to their rigid furan-containing backbones. Herein, we develop two strategies to polymerize methyl 5-hydroxymethyl furanoate to poly-(5-hydroxymethyl furanoate) (PHMF), a furan-based polyester with even greater backbone rigidity than poly-(ethylene furanoate). Thermal, spectroscopic, and computational investigations of PHMF alongside analogous furan-based and phenyl-based polyesters suggest that the high furan content of PHMF leads to its high glass transition temperature, slow crystallization kinetics, and low amorphous mobility. Molecular dynamics simulations suggest that while the backbone of PHMF is exceptionally rigid, its amorphous phase is denser than its phenyl analog due to noncovalent interchain interactions. Together, these results highlight how asymmetric furan-based monomers can modulate key properties in biobased polyesters.

The thermosetting polymer matrix in fiber reinforced composites is an important component for energy related applications, such as the lightweighting of vehicles or their use in wind and waterpower turbine blades, due to their ability to provide superior adhesion, stiffness, and applicability to a wide range of manufacturing processes. Despite these benefits, today's thermosets are widely considered to be unrecyclable; thus, there is a large interest in redesigning these materials to be inherently recyclable so that energy intensive production of fibers and monomers can be circumvented, bolstering composite manufacture supply chains. Polyester covalent adaptable networks (PECANs) are one such promising alternative to the incumbent, nonrecyclable epoxy-amine thermosets. PECANs can be formed from the ring-opening co-polymerization (ROCOP) of epoxy-anhydride monomer mixtures and subsequent curing at mild temperatures to exhibit similar performance to conventional epoxies while also possessing unique dynamic chemistries along the ester-hydroxyl backbone that are capable of transesterification and thus reprocessability. While significant advancements have been made in formulating these materials for improved mechanical properties or optimizing solvolysis and reprocessing strategies, less attention has been placed on the impact of the residing amine catalyst used to generate the polyester network. In this work, we evaluated the triple-catalytic efficacy of 12 tertiary amines that act as a curing (bulk ROCOP), a transesterification (internal bond exchange), and a deconstruction (methanolysis) catalyst for PECAN thermosets. Specifically, we first distinguish between chain-growth and step-growth polymerization mechanisms for epoxy-amine and epoxy-anhydride mechanisms. We also utilized density functional theory (DFT) to estimate the basicity (pKb) of each catalyst. Of the tested catalysts, the ROCOP of the studied PECAN network can be completed between 95 and 247 min (at 80 degrees C), with variable gelation phenomena. Additionally, the stress relaxation (transesterification metric) efficiency of the tested PECAN networks with alternative embedded catalysts ranged from 95% to 15% reduction in stress after 5 h at 200 degrees C, and the depolymerization efficacy ranged from 2.5% to 9.8% deconstruction after 36 h at 130 degrees C. Overall, the nitrogen-based moieties were demonstrated to influence polymerization kinetics, catalyze the dynamic transesterification exchange mechanism, and aid in the solvolysis of the thermosets at end-of-life.

Adhesives are important in creating multilayer products, such as in packaging and construction. Most current hot-melt adhesives such as poly(ethylene-co-vinyl acetate) (EVA) and polyurethanes lack chemical recyclability and do not easily de-bond, complicating recycling. Here, we achieved tunable adhesive properties of chemically recyclable polyolefin-like multiblock copolymers through regulating the incorporation of crystalline hard blocks, amorphous soft blocks, and ester content highlighted by adhesive strengths up to 6.80 MPa. We further demonstrated applications of these adhesives in multi-layer films and showed that the adhesives can be readily de-bonded, recovered, and chemically recycled. Overall, this study into structure–property relationships, including effects of crystallinity, soft-block incorporation, and ester content of the multiblock copolymers on adhesive properties, has resulted in a modular hot-melt adhesive platform that exhibits chemical recyclability for virgin-quality adhesive re-generation, reprocessability for repeated reuse of the recovered adhesive, and tunability for designing adhesives with a wide range of low to high (up to ∼80% stronger than EVA) adhesion strengths.

Thermal energy regulation is a significant challenge, contributing to over 30% of annual greenhouse gas emission (GHG) emissions. Phase change materials (PCMs) offer a promising solution by storing thermal energy, which can enable the reuse of waste heat for heating and cooling; however, developing materials for shape-stabilized PCMs remains crucial. This work investigates a self-foaming poly(hydroxy)urethane (PHU), derived from a non-isocyanate polyurethane (NIPU), as a porous support for shape-stabilizing paraffinic and salt hydrate PCMs. PHU-encapsulated paraffinic PCMs exhibited excellent thermal stability over repeated cycles. Thermal stability with salt hydrate PCMs, specifically calcium chloride hexahydrate (CaCl2 center dot 6H2O), is achieved by the incorporation of 5 wt.% barium carbonate (BaCO3) into the PHU foam. This enabled stable cycling for over 48 cycles with desirable thermal properties, i.e., a melting point approximate to 30 degrees C, high enthalpy (ca. 138 J g-1 per cycle), and a consistent freezing point approximate to 20 degrees C, making it suitable for applications in buildings and electric vehicle battery insulation. Also, incorporating graphite (1.5-10 wt.%) into the foam enhanced the thermal conductivity of shape-stabilized CaCl2 center dot 6H2O during heating and cooling cycles. Overall, the approach detailed here offers a carbon-conscious and chemically tunable material for thermal energy storage.

Petroleum-derived polyolefins exhibit diverse properties and are the most important and largest volume class of plastics. However, polyolefins are difficult to efficiently recycle or break down and are now a persistent global contaminant. Broadly replacing polyolefins with bio-derived and degradable polyethylene-like materials is an important yet challenging endeavour towards sustainable plastics. Here we report a solution for circular bio-based polyethylene-like materials synthesized by acceptorless dehydrogenative polymerization from linear and branched diols and their catalytic closed-loop recycling. The polymerization and depolymerization processes utilize earth-abundant manganese complexes as catalysts. These materials exhibit a wide range of mechanical properties, encompassing thermoplastics to plastomers to elastomers. The branched diols, produced through a thiol-ene click reaction, can be polymerized to plastics with significantly enhanced tensile properties, toughness and adhesive properties. These materials could be depolymerized back to monomers through hydrogenation and were separatable with a monomer recovery of up to 99%, unaffected by the presence of dyes and additives. Overall, this system establishes a route to more sustainable plastics.

Carbon fibre-reinforced polymers (CFRPs) are used in many applications in the global energy transition, including for lightweighting aircraft and vehicles and in wind turbine blades, shipping containers and gas storage vessels1-4. Given the high cost and energy-intensive manufacture of CFRPs5-7, recycling strategies are needed that recover intact carbon fibres and the epoxy-amine resin components. Here we show that acetic acid efficiently depolymerizes both aliphatic and aromatic epoxy-amine thermosets used in CFRPs to recoverable monomers, yielding pristine carbon fibres. Deconstruction of materials from multiple sectors demonstrates the broad applicability of this approach, providing clean fibres from 2 h reactions. The optimal conditions were scaled to 80.0 g of post-consumer CFRPs, and demonstrative composites were fabricated from the recycled carbon fibres, which were recycled two more times, maintaining their strength throughout. Process modelling and techno-economic analysis, with feedstock cost informed by wind turbine blade waste generation8, indicates this method is cost effective, with a minimum selling price of US$1.50 per kg for recycled carbon fibres whereas life cycle assessment shows process greenhouse gas emissions around 99% lower than virgin carbon fibre production. Overall, this approach could enable recycling of industrial CFRPs as it provides clean, mechanically viable recycled carbon fibres and recoverable resin monomers from the thermoset.

Polyethylene (PE) is the most widely produced plastic but accumulation and resistance to degradation has significantly contributed to the plastic waste crisis. Upcycling has presented promising solutions to transform PE waste into value-added products. In this study, mixed post-consumer PE was successfully repurposed into reprocessable and chemically recyclable cross-linked polyethylene (XLPE). This process involved converting PE into telechelic oligomers, followed by repolymerization using a hybrid cross-linking system consisting of a dynamic cross-linker 2,4,6-triethoxy-1,3,5-triazine (TETA) and non-dynamic cross-linker tris(6-isocyanatohexyl)isocyanurate (Tri-HDI). In the resulting XLPE, TETA facilitated iterative reprocessing with minimal property degradation across cycles, whereas Tri-HDI helped preserve functional performance throughout service life. Compared to PE, XLPE exhibited enhanced mechanical properties, reduced creep deformation under application-relevant temperatures, and high temperature structural stability. Notably, copolymerizing PE oligomers with commercial macrodiols was employed to create composite XLPEs, enabling tuning material properties. After use, XLPE can be efficiently and selectively depolymerized under mild conditions, even when mixed with commercial insulator cables. This depolymerization allows for the recovery of the constituent building blocks, enabling purification and subsequent repolymerization for reuse. This approach demonstrates the potential of repurposing plastic waste into sustainable materials and fostering the development of a circular economy.

Synthetic polymers have found widespread use, but their ineffective end-of-life treatment is causing a significant environmental and human health crisis. Here, we demonstrate the upcycling of polynorbornene derivatives (pNBEs) through their deconstruction into distinct oligomeric buildings blocks that can be repolymerized into chemically recyclable pNBEs-like multiblock polymers via dehydrogenative polymerization. The resulting materials exhibit diverse mechanical properties, while integrating high melting temperatures (Tm as high as 133 °C). Notably, this method could also enable the selective deconstruction of permanently cross-linked polydicyclopentadiene (pDCPD) thermosets into telechelic-OH functionalized oligomers, overcoming the significant challenges posed by their robust network structure in recycling and degradation. The resulting pDCPD oligomers can subsequently be repolymerized with macrodiols to create multiblock thermosets with tunable mechanical properties, including Young's modulus and tensile elongation. After use, upcycled plastics could be effectively deconstructed back to the oligomers for recovery and repolymerization. Overall, this work establishes an approach that can be utilized to upcycle pNBEs into previously inaccessible multiblock thermosets and thermoplastics with full recyclability, and may be generalizable to a range of polymers to shift their end-of-life waste disposal toward sustainable recovery and reuse.

Herein, we report a selective photooxidation of commodity postconsumer polyolefins to produce polymers with in-chain ketones. The reaction does not involve the use of catalyst, metals, or expensive oxidants, and selectively introduces ketone functional groups. Under mild and operationally simple conditions, yields up to 1.23 mol % of in-chain ketones were achieved. Installation of in-chain ketones resulted in materials with improved adhesion of the materials and miscibility of mixed plastics relative to the unfunctionalized plastics. The introduction of ketone groups into the polymer backbone allows these materials to react with diamines, forming dynamic covalent polyolefin networks. This strategy allows for the upcycling of mixed plastic waste into reprocessable materials with enhanced performance properties compared to polyolefin blends. Mechanistic studies support the involvement of photoexcited nitroaromatics in consecutive hydrogen and oxygen atom transfer reactions.

Fiber-reinforced polymers (FRPs) are critical for energy-relevant applications such as wind turbine blades. Despite this, the end-of-life options for FRPs are limited as they are permanently cross-linked thermosets. To enable the circularity of FRPs, we formulated a bio-derivable polyester covalently adaptable network (PECAN), sometimes referred to as a polyester vitrimer, to manufacture FRPs at >1 kg scale, which is accomplished as the resin is infusible (175-425 cP at 25 degrees C viscosity), can be cured at 80 degrees C within 5 h and is depolymerizable via methanolysis yielding high-quality fibers and recoverable hardener. The FRPs exhibit a transverse tensile modulus comparable with today's wind relevant FRPs (10.4-11.9 GPa). Modeling estimates a resin minimum selling price of $2.28/kg and, relative to an epoxy-amine resin, PECAN manufacture requires 19%-21% less supply chain energy and emits 33%-35% less greenhouse gas emissions. Overall, this study suggests that redesigned thermosets can yield beneficial circularity.

Large composite structures, such as those used in wind energy applications, rely on the bulk polymerization of thermosets on an impressively large scale. To accomplish this, traditional thermoset polymerizations require both elevated temperatures (>100 degrees C) and extended cure durations (>5 h) for complete conversion, necessitating the use of oversize ovens or heated molds. In turn, these requirements lead to energy-intensive polymerizations, incurring high manufacturing costs and process emissions. In this study, we develop thermoset polymerizations that can be initiated at room temperature through a transformative "chemical heating" concept, in which the exothermic energy of a secondary reaction is used to facilitate the heating of a primary thermoset polymerization. By leveraging a redox-initiated methacrylate free radical polymerization as a source of exothermic chemical energy, we can achieve peak reaction temperatures >140 degrees C to initiate the polymerization of epoxy-anhydride thermosets without external heating. Furthermore, by employing Trojan horse methacrylate monomers to induce mixing between methacrylate and epoxy-anhydride domains, we achieve the synthesis of homogeneous hybrid polymeric materials with competitive thermomechanical properties and tunability. Herein, we establish a proof-of-concept for our innovative chemical heating method and advocate for its industrial integration for more energy-efficient and streamlined manufacturing of wind blades and large composite parts more broadly.