As the industry marches on onto the 5nm node and beyond, scaling has slowed down, with all major IDMs & foundries predicting a 3-4 year cadence for scaling. A major reason for this slowdown is not the technical challenge of making features smaller, but effective control of variation that creeps in to the fabrication process. That variability manifests itself as edge placement error (EPE), which has a direct impact on wafer yield. Simply defined as the variance between design intent vs. actual on-wafer results, EPE is one of the foremost challenges being faced by the industry at the advanced node for both logic and memory. This is especially critical at three stages: the front end of line (FEOL) STI patterning; middle of line (MOL) contact patterning; and back end of line (BEOL) trench patterning where the desired tight pitch demands EPE control beyond the capability of 193i multi-patterning or even EUV single pattern. In order to mitigate this EPE challenge, we are proposing self-alignment of blocks & cuts through a multi-color materials integration concept. This approach, termed as “Self-aligned block or Cut (SAB or SACut)”, simply trades off the un-manageable overlay requirement into a more manageable etch selectivity challenge, by having multiple materials filled in every other trench or line. In this paper we will introduce self-alignment based block and cut strategies using multi-color materials integration and show implementation for BEOL trench block patterning. We will present a breakdown of the key unit process challenges that were needed to be resolved for enabling the self-alignment such as: (a) material selection of multi-color approach; (b) planarization of spin on materials; (c) void-free gap fill for high aspect ratio features; and last but not the least, (c) etch selectivity of etching one material with respect to all other materials exposed. Further, we will present a comparison of our new self-alignment approach with standard approaches where we will articulate the advantages in terms of EPE relaxation and mask number reduction. We will conclude our talk with a brief snapshot of the future direction of our EPE improvement strategies and our view on the future of patterning beyond 5nm node for the industry.

In this work, we present and compare two integration approaches to enable self-alignment of the block suitable for the 5-nm technology node. The first approach is exploring the insertion of a spin-on metal-based material to memorize the first block and act as an etch stop layer in the overall integration. The second approach is evaluating the self-aligned block technology employing widely used organic materials and well-known processes. The concept and the motivation are discussed considering the effects on design and mask count as well as the impact on process complexity and EPE budget. We show the integration schemes and discuss the requirements to enable self-alignment. We present the details of materials and processes selection to allow optimal selective etches and we demonstrate the proof of concept using a 16-nm half-pitch BEOL vehicle. Finally, a study on technology insertion and cost estimation is presented.

Patterning the desired narrow pitch at 10nm technology node and beyond, necessitates employment of either extreme ultra violet (EUV) lithography or multi-patterning solutions based on 193nm-immersion lithography. With enormous challenges being faced in getting EUV lithography ready for production, multi-patterning solutions that leverage the already installed base of 193nm-immersion-lithography are poised to become the industry norm for 10 and 7nm technology nodes. For patterning sub-40nm pitch line/space features, self-aligned quadruple patterning (SAQP) with resist pattern as the first mandrel shows significant cost as well as design benefit, as compared to EUV lithography or other multi-patterning techniques. One of the most critical steps in this patterning scheme is the resist mandrel definition step which involves trimming / reformation of resist profile via plasma etch for achieving appropriate pitch after the final pattern. Being the first mandrel, the requirements for the Line Edge Roughness (LER) / Line Width Roughness (LWR); critical dimension uniformity (CDU); and profile in 3-dimensions for the resist trim / reformation etch is extremely aggressive. In this paper we highlight the unique challenges associated in developing resist trim / reformation plasma etch process for SAQP integration scheme and summarize our efforts in optimizing the trim etch chemistries, process steps and plasma etch parameters for meeting the mandrel definition targets. Finally, we have shown successful patterning of 30nm pitch patterns via the resist-mandrel SAQP scheme and its implementation for Si-fin formation at 7nm node.

A lattice-type Monte Carlo-based mesoscale model and simulation of the lithography process have been adapted to study the insoluble particle generation that arises from statistically improbable events. These events occur when there is a connected pathway of soluble material that envelops a volume of insoluble material due to fluctuations in the deprotection profile. The simulation shows that development erodes the insoluble material into the developer stream and produces a cavity on the line edge that can be far larger than a single polymer molecule. The insoluble particles can coalesce to form aggregates that deposit on the wafer surface. The effect of the resist formulation, exposure, postexposure bake, and development variables on particle generation was analyzed in both low- and high-frequency domains. It is suggested that different mechanisms are dominant for the formation of line-edge roughness (LER) at different frequencies. The simulations were used to assess the commonly proposed measures to reduce LER such as the use of low molecular weight polymers, addition of quenchers, varying acid diffusion length, etc. The simulation can be used to help set process variables to minimize the extent of particle generation and LER. (C) 2014 Society of Photo-Optical Instrumentation Engineers (SPIE)

Directed Self-Assembly (DSA) is gaining momentum as a means for extending optical lithography past its current limits. There are many forms of the technology, and it can be used for creating both line/space and hole patterns.1-3 As with any new technology, adoption of DSA faces several key challenges. These include creation of a new materials infrastructure, fabrication of new processing hardware, and the development of implementable integrations. Above all else, determining the lowest possible defect density remains the industry's most critical concern. Over the past year, our team, working at IMEC, has explored various integrations for making 12-14nm half-pitch line/space arrays. Both grapho- and chemo-epitaxy implementations have been investigated in order to discern which offers the best path to high volume manufacturing. This paper will discuss the manufacturing readiness of the various implementations by comparing the process margin for different DSA processing steps and defect density for the entirety of the flow. As part of this work, we will describe our method for using programmed defectivity on reticle to elucidate the mechanisms that drive self-assembly defectivity on wafer.

The goal of this work is to use a combination of experiment and calibrated resist models to understand the impact of photo-acid generator (PAG) and sensitizer loading on the performance of a polymer bound PAG resist based processes for extreme ultraviolet (EUV) lithography. This paper describes construction of a chemically amplified resist model across 248 nm, 193 nm, and EUV imaging wavelengths. Using resist absorbance input as obtained from experiment and modeling, only the acid formation kinetics are allowed to vary across imaging wavelengths. This constraining system affords very good fitting results, which provides high confidence that the extracted parameters from the model have actual physical significance. The quantum efficiency for acid formation in EUV is found to be similar to 8x higher than at 248 or 193 nm, due to the excitation mechanism by secondary electrons. Most notably for the polymer bound PAG system under study the model provides an extremely low acid diffusion length (similar to 8 nm), suggesting an excellent inherent resolution for this material. Next, resist models are created for a series of sensitizer containing polymer bound PAG formulations, where the sensitizer loading is systematically varied. Compared to the reference polymer bound PAG resist without sensitizer the efficiency of acid formation is significantly increased, without a negative impact on either resolution or linewidth roughness. For these materials the quantum efficiency of acid formation in EUV is found to be similar to 12x higher than at 248 nm. In these formulations the impact of sensitizer loading on the sizing dose is found to be rather moderate. This may suggest that even at the lowest sensitizer loading studied the energy of the secondary electrons is already efficiently transferred to the PAGs. (C) 2011 Society of Photo-Optical Instrumentation Engineers (SPIE). [DOI: 10.1117/1.3555090]

This paper describes construction of a chemically amplified resist model across 248nm, 193nm and EUV imaging wavelengths. Using resist absorbance input as obtained from experiment and modeling, only the acid formation kinetics are allowed to vary across imaging wavelengths. This very constraining system affords very good fitting results, which provides high confidence that the extracted parameters from the model have actual physical significance. The quantum efficiency for acid formation in EUV is found to be similar to 8X higher than at 248 or 193nm, due to the excitation mechanism by secondary electrons. Most notably for the polymer bound PAG system under study the model provides an extremely low acid diffusion length (similar to 7nm), suggesting an excellent inherent resolution for this material.Next, resist models are created for a series of sensitizer containing polymer bound PAG formulations, where the sensitizer loading is systematically varied. Compared to the reference polymer bound PAG resist without sensitizer the efficiency of acid formation is significantly increased, without a negative impact on either resolution or line width roughness. For the materials the quantum efficiency of acid formation in EUV is found to be similar to 12X higher than at 248nm. In these formulations the impact of sensitizer loading on the sizing dose is found to be rather moderate. This may suggest that even at the lowest sensitizer loading studied the energy of the secondary electrons is already efficiently transferred to the PAGs.

Current minimum feature sizes in the microelectronics industry dictate that molecular interactions affect process fidelity and produce stochastic excursions like line edge roughness (LER). The composition of future resists is still unknown at this point, and so simulation of various resist platforms should provide useful information about resist design that minimizes LER. In the past, researchers developed a mesoscale model for exploring representative 248 nm resist systems through dynamic Monte Carlo methods and adaptation of critical ionization theory. This molecular modeling uses fundamental interaction energies combined with a Metropolis algorithm to model the full lithographic process (spin coat, PAB, exposure, PEB, and development). Application of this model to 193 nm platforms allows for comparison between 248 and 193 nm resist systems based on molecular interactions. This paper discusses the fundamental modifications involved in adapting the mesoscale model to a 193 nm platform and investigates how this new model predicts well-understood lithographic phenomena including the relationship between LER and aerial image, the relationship between LER and resist components, and the impact of non-uniform PAG distribution in the resist film. Limited comparisons between the 193 nm system and an analogous 248 nm platform will be discussed.