
Spinel nanoferrites have gained a lot of attention for high-frequency and microwave absorption applications due to their tunable magnetic, electrical, dielectric and electromagnetic characteristics. This review focuses on the Nickel–Zinc (Ni–Zn), Magnesium–Zinc (Mg–Zn), and Cobalt–Zinc (Co–Zn) nanoferrites and the impact of rare earth doping on composition, cation distribution, microstructure, magnetic, electrical and microwave absorption characteristics. The structural and morphological properties of these nanoferrites, such as crystallite size, grain growth, agglomeration, porosity, and interfacial regions, have been correlated with their magnetic and electrical properties. The saturation magnetization ( M s ), Coercivity ( H c ), magnetic anisotropy ( K ), dielectric response, impedance and associated charge transport mechanism are discussed in detail. The microwave absorption performance parameters such as reflection loss ( RL ), effective absorption bandwidth (EAB) and magnetic and dielectric losses are analyzed for the available literature. Reported results show that an appropriate concentration of Zn, thermal treatment, rare-earth substitution, and composite formation can significantly modify the cation distribution, magnetic resonance, interfacial polarization, and electromagnetic attenuation. The Ni–Zn nanoferrites give balanced high-frequency performance; the Mg–Zn nanoferrites offer high resistivity and low magnetic loss, whereas the Co–Zn ferrites exhibit strong magnetic anisotropy and effective microwave absorption. Thus, the composition and microstructure variation provide a promising route for the development of spinel nanoferrite-based materials for microwave absorption, EMI shielding, wireless communication, and advanced high-frequency electronic device systems.
This work demonstrates the scalable fabrication of a two-dimensional (2D) SnS2-based metal-semiconductor-metal (MSM) structured gas sensor and systematically investigates its layer-dependent sensing behaviors toward various gas species. Few-layer SnS2 films were synthesized and comprehensively characterized using X-ray diffraction (XRD) and Raman spectroscopy to confirm their high crystallinity, predominant phase purity, c-axis preferred orientation, and characteristic lattice vibrations. X-ray photoelectron spectroscopy (XPS) and cross-sectional transmission electron microscopy (TEM) were further utilized to validate the chemical bonding states-including trace surface-oxygen/residual-oxide contributions-and precise layer-number configurations, respectively. The MSM devices were evaluated for their gas-sensing capabilities under varying thermal conditions at a fixed concentration of 5 Parts per Million (ppm). The experimental results reveal that the sensor response, operating temperature, sensitivity, and selectivity profile are strongly dictated by the precise number of SnS2 layers. Specifically, the bi-layer SnS2 sensor yields the highest absolute sensitivity at the 50 degrees C operating temperature, while the tri-layer configuration exhibits the most robust performance when restricted to room-temperature (25 degrees C) operation. Outstanding sensitivity and specific selectivity toward NO2 were achieved, highlighting the immense potential of layer-controlled 2D SnS2 frameworks for advanced, high-performance environmental monitoring applications.
Abstract An α-phase Ga2O3 (α-Ga2O3 ) thin film layer was grown on a sapphire substrate by halide vapor phase epitaxy (HVPE), and an α-Ga2 O3 based Schottky diode hydrogen sensor was fabricated. Hydrogen sensing characteristics on the α-Ga2O3 surface were investigated at temperature range from 25 to 500°C. The device showed a hydrogen responsivity of 187% for 500 ppm hydrogen exposure, and exhibited a distinctive current increase response to 50 -500 ppm hydrogen concentrations at 100°C. The hydrogen sensor presented a distinctive hydrogen response up to 500°C, and a decent hydrogen cross-selectivity over other gases including N₂, CO, CO2 , CH4 , NO2 , NH3 , and O2 . Furthermore, the effect of crystal structure of the α-Ga2O3 surface on the hydrogen sensing behavior was examined.
Chemical mechanical planarization (CMP) of copper-filled through-glass vias (TGVs) requires sequentially removing the Cu overburden and Ta barrier while controlling Cu dishing and glass roughness. Electrochemical, dissolution, CMP removal-rate, direct Cu–Ta galvanic, and patterned-TGV polishing measurements were combined to examine how slurry chemistry affects these evolving interfaces. Increasing oxalic acid concentration strongly activated Cu, whereas Ta remained passive, with corrosion current densities below approximately 0.01 μA cm − 2 throughout the acidic ligand-series experiments, providing a basis for Cu/Ta selectivity. Benzotriazole (BTA) inhibition depended strongly on pH. At pH 5, BTA suppressed Cu corrosion and dissolution, whereas at pH 10 it substantially reduced dissolution without decreasing the Tafel-derived corrosion current. Direct coupling measurements demonstrated that isolated Cu–Ta corrosion-potential differences did not reliably predict galvanic current. At pH 10, 10 mM BTA reduced galvanic-current magnitude by approximately 61%. Increasing hydrogen peroxide concentration enhanced bulk Cu removal while Ta removal remained comparatively low. Patterned-TGV polishing revealed a trade-off: alkaline barrier finishing yielded the lowest glass RMS roughness (0.56 nm), whereas acidic barrier finishing yielded the lowest mean Cu dishing (0.37 μm). Effective TGV planarization therefore requires stage-specific control of slurry chemistry and polishing conditions rather than optimization using a single electrochemical or removal metric.
Contamination of water by pesticides, antibiotics, pharmaceuticals and other persistent organic compounds creates environmental and food-safety concerns. Zinc oxide (ZnO) is a promising semiconductor photocatalyst, but its practical performance is limited by ultraviolet-dominated absorption, electron–hole recombination and photocorrosion. This narrative and critical review examines how defect engineering, elemental doping, heterojunctions and carbon coupling influence ZnO structure, surface chemistry and charge-carrier behavior in water purification. The supplied literature was assessed for material composition, synthesis, irradiation conditions, pollutant removal, mechanistic evidence, catalyst reuse, transformation products, toxicity and leaching where reported. Studies of Ag-, Pd-, Ce-, Tb- and Er-modified ZnO and oxide/carbon composites demonstrate that modified systems can improve degradation of selected contaminants, although results depend strongly on irradiation, catalyst dosage, pH, pollutant concentration and water matrix. The evidence also shows that disappearance of a parent contaminant does not necessarily establish mineralization or detoxification; transformation products may retain or increase toxicity. Reliable translation to water treatment therefore requires complementary defect characterization, standardized performance reporting, transformation-product and toxicity analysis, catalyst recovery, leaching assessment and energy evaluation. The review identifies ZnO/CuO, ZnO/TiO 2 and ZnO/carbon systems as research directions whose practical advantages must be validated under realistic water-treatment conditions.