
During the middle and late stages of oilfield development in China, crude⁃oil water cut tends to increase, adversely affecting both crude⁃oil production quality and oilfield development efficiency. Accurate measurement of water cut is essential for crude⁃oil processing, transportation, and storage; therefore, real⁃time and precise water⁃cut measurement is of considerable practical importance in oilfield production. To address the challenge of accurately measuring high⁃water⁃cut crude oil in real time, an optimized five⁃electrode measurement configuration was developed for an annular⁃array conductance sensor based on the conductance method. First, the sensor dimensions and structural parameters were optimized through sensitivity analysis using MAXWELL simulation software. Next, a signal excitation circuit and a signal processing circuit were designed to ensure measurement stability and data accuracy. Finally, experiments were conducted to measure the water cut of high⁃water⁃cut crude oil. The results show that the proposed method provides high measurement accuracy, requires simple peripheral circuitry, and exhibits strong resistance to electromagnetic interference. In addition, the system measurements closely follow the actual variation in water cut, with relatively small overall errors and good stability and repeatability.
The metallogenic controls on the sandstone⁃type uranium deposit in the Upper Cretaceous Yaojia Formation of the Qianjiadian area, Kailu Basin, remain debated, and the sedimentary environment, provenance characteristics, and uranium enrichment mechanisms have yet to be well constrained. Uranium⁃bearing strata of the Yaojia Formation were systematically sampled from drill cores. Major⁃element and rare⁃earth⁃element (REE) concentrations and organic⁃matter contents were analyzed using X⁃ray fluorescence spectrometry (XRF), inductively coupled plasma mass spectrometry (ICP⁃MS), and related methods. The results show that rocks from the oxidized zone exhibit pronounced negative Ce and Eu anomalies, with δCe values of 0.67-0.89 and δEu values of 0.78-0.92, indicating that Ce and Eu anomaly parameters can effectively discriminate redox conditions; Uranium mass fraction is negatively correlated with the m(K₂O)/m(Na₂O), and all high⁃uranium samples have m(K₂O)/m(Na₂O)<2, indicating that high⁃permeability sandstones provided favorable pathways for uranium⁃bearing fluids; Integrated analysis of sedimentary facies, geochemical discrimination diagrams, and the regional tectonic setting indicates that the Yaojia Formation was deposited in a passive continental⁃margin setting; and the principal metallogenic control is the coupling of a regionally developed oxidation zone controlled by tectonic tilting with locally developed structural windows, with the main mineralization event occurring at approximately 67 Ma. This study establishes an integrated "source⁃migration⁃accumulation" uranium metallogenic model for the study area and provides a theoretical basis for exploring sandstone⁃type uranium deposits in the Kailu Basin and comparable basins.
Spark plasma sintering is a rapid, low⁃temperature, high⁃density sintering technique that facilitates the fabrication of dense compacts while mitigating excessive grain growth and insufficient densification. This study systematically investigated the effects of sintering pressure on the microstructure and thermophysical properties of Al⁃0.6Si composites prepared by spark plasma sintering. The results show that sintering pressure strongly influences the properties of high⁃silicon aluminum composites. At a sintering pressure of 40 MPa, the Al⁃0.6Si composite exhibits the densest microstructure and the smallest average silicon⁃phase size. Its thermal conductivity is 130.35 W/(m·K), thermal expansion coefficient is 8.51×10⁻⁶ K⁻¹, Vickers hardness is 329.2 HV, density is 2.394 3 g/cm³, and relative density reaches 96.93%. These results demonstrate that optimizing the sintering pressure is an effective route to preparing high⁃performance composites for electronic packaging and provides process guidance for their fabrication.
Diesel fuel stored for long periods in emergency diesel tanks at nuclear power plants is susceptible to deterioration, potentially compromising the operational efficiency and reliability of emergency diesel units and posing risks to nuclear power plant safety. To maintain fuel quality, periodic filtration and blending, with additives when necessary, are required. Accordingly, this study proposes an efficient and accurate optimization method for emergency diesel conditioning that integrates computational fluid dynamics (CFD) simulations in FLUENT with a genetic algorithm implemented in MATLAB. The conditioning process is first simulated and analyzed using CFD, after which the genetic algorithm performs global optimization to determine a conditioning scheme that enables the monitoring points to meet the blending requirements in the shortest possible time. The proposed model improves the efficiency and accuracy of the conditioning process while reducing conditioning time, thereby supporting the operational reliability and performance of emergency diesel units.
In this study, Cu⁃doped TiO₂ photocatalysts were prepared by the sol⁃gel method using tetrabutyl titanate as the titanium source and copper(II) chloride dihydrate as the copper source. Their phase composition, morphology, and surface chemical composition were characterized by XRD, SEM, and XPS; photoelectrochemical tests were conducted to investigate the photoelectrocatalytic properties of the materials, and Rhodamine B (RhB) was used as the target pollutant to evaluate their photo⁃Fenton catalytic performance,the mechanism by which Cu doping enhances the photo⁃Fenton activity of TiO₂ was also elucidated. The results show that 5% Cu⁃TiO₂ exhibits the best performance for RhB degradation, with a degradation rate constant 7.0 times that of TiO₂. This enhancement is mainly attributed to Cu doping, which introduces impurity energy levels into TiO₂, significantly narrows the band gap, and extends the photoresponse into the visible⁃light region, thereby improving the photo⁃Fenton catalytic performance.