A complete, general solution for collecting and processing data from gaseous tracking detectors in high-rate applications has been developed. The readout chain consists of front-end modules equipped with PASTTREC ASIC chips and trigger readout boards version 3 (TRBv3) as a readout platform. The platform is accompanied by dedicated control, monitoring, and data quality assessment software. The entire system has been evaluated with a tracking system based on straw detectors in laboratory and in-beam experiments. In this paper, we present key elements of the system as well as results of various tests. The measured PASTTREC operation characteristics and the TRBv3 specification used for the readout allow us to adapt and to integrate it to the existing HADES spectrometer and the PANDA detector, an experiment under construction, both located at the FAIR facility in Darmstadt.

The design of the Forward Tracker for the Forward Spectrometer of the PANDA experiment is described. The tracker consists of 6 tracking stations, each comprising 4 planar double layers of straw tube detectors, and has a total material budget of only 2% X-0. The straws are made self-supporting by a 1 bar over-pressure of the working gas mixture (Ar/CO2). This allows to use lightweight and compact rectangular support frames for the double layers and to split the frames into pairs of C-shaped half-frames for an easier installation on the beam line.

The exclusive charmonium production process in $\overline{p}p$ annihilation with an associated ${\ensuremath{\pi}}^{0}$ meson $\overline{p}p\ensuremath{\rightarrow}J/\ensuremath{\psi}{\ensuremath{\pi}}^{0}$ is studied in the framework of QCD collinear factorization. The feasibility of measuring this reaction through the $J/\ensuremath{\psi}\ensuremath{\rightarrow}{e}^{+}{e}^{\ensuremath{-}}$ decay channel with the AntiProton ANnihilation at DArmstadt ($\overline{\mathsf{P}}\mathsf{ANDA}$) experiment is investigated. Simulations on signal reconstruction efficiency as well as the background rejection from various sources including the $\overline{p}p\ensuremath{\rightarrow}{\ensuremath{\pi}}^{+}{\ensuremath{\pi}}^{\ensuremath{-}}{\ensuremath{\pi}}^{0}$ and $\overline{p}p\ensuremath{\rightarrow}J/\ensuremath{\psi}{\ensuremath{\pi}}^{0}{\ensuremath{\pi}}^{0}$ reactions are performed with PandaRoot, the simulation and analysis software framework of the $\overline{\mathsf{P}}\mathsf{ANDA}$ experiment. It is shown that the measurement can be done at $\overline{\mathsf{P}}\mathsf{ANDA}$ with significant constraining power under the assumption of an integrated luminosity attainable in four to five months of data taking at the maximum design luminosity.

Bound nuclear systems with two units of strangeness are still poorly known despite their importance for many strong interaction phenomena. Stored antiprotons beams in the GeV range represent an unparalleled factory for various hyperon-antihyperon pairs. Their outstanding large production probability in antiproton collisions will open the floodgates for a series of new studies of systems which contain two or even more units of strangeness at the PANDA experiment at FAIR. For the first time, high resolution gamma-spectroscopy of doubly strange Lambda Lambda-hypernuclei will be performed, thus complementing measurements of ground state decays of Lambda Lambda-hypernuclei at J-PARC or possible decays of particle unstable hypernuclei in heavy ion reactions. High resolution spectroscopy of multistrange Xi(-) -atoms will be feasible and even the production of Omega(-) -atoms will be within reach. The latter might open the door to the vertical bar S vertical bar = 3 world in strangeness nuclear physics, by the study of the hadronic Omega(-) -nucleus interaction. For the first time it will be possible to study the behavior of Xi(+) in nuclear systems under well controlled conditions. (C) 2016 Elsevier B.V. All rights reserved.

The CMS Beam Radiation Instrumentation and Luminosity (BRIL) project is composed of several systems providing the experiment protection from adverse beam conditions while also measuring the online luminosity and beam background. Although the readout bandwidth of the Fast Beam Conditions Monitoring system (BCM1F one of the faster monitoring systems of the CMS BRIL), was sufficient for the initial LHC conditions, the foreseen enhancement of the beams parameters after the LHC Long Shutdown-1 (LS1) imposed the upgrade of the system. This paper presents the new BCM1F, which is designed to provide real-time fast diagnosis of beam conditions and instantaneous luminosity with readout able to resolve the 25 ns sub-bunch structure. Presented at TWEPP 2015 TWEPP 2015 Topical Workshop on Electronics for Particle Physics New Fast Beam Conditions Monitoring (BCM1F) system for CMS Agnieszka A. Zagozdzinska a, b *, Alan J.Bellg, Anne E. Dabrowskia, Maria Hempeld, Hans.M.Henschel d, Olena Karacheban d, Dominik Przyborowski c, Jessica L. Leonard d, Marek Penno d, Krzysztof T. Pozniak b, Marco Miraglia a, e, Wolfgang Lange d, Wofgang Lohmann d,f, Vladimir Ryjov a, Arkady Lokhovitskiyg, David Stickland c, Roberval Walsh d, on behalf of the CMS Collaboration a CERN, Geneva, Switzerland b Warsaw University of Technology, Warsaw, Poland c AGH University of Science and Technology, Warsaw, Poland d DESY, Zeuthen, Germany, Zeuthen, Germany e Sezione di Pisa, Piza, Italy f Branderburg University of Technology, Branderburg, Germany g University of Canterbury, Christchurch, New Zealand E-mail: a.zago@cern.ch ABSTRACT: The CMS Beam Radiation Instrumentation and Luminosity (BRIL) project is composed of several systems providing the experiment protection from adverse beam conditions while also measuring the online luminosity and beam background. Although the readout bandwidth of the Fast Beam Conditions Monitoring system (BCM1F one of the faster monitoring systems of the CMS BRIL), was sufficient for the initial LHC conditions, the foreseen enhancement of the beams parameters after the LHC Long Shutdown-1 (LS1) imposed the upgrade of the system. This paper presents the new BCM1F, which is designed to provide real-time fast diagnosis of beam conditions and instantaneous luminosity with readout able to resolve the 25 ns bunch structure. The CMS Beam Radiation Instrumentation and Luminosity (BRIL) project is composed of several systems providing the experiment protection from adverse beam conditions while also measuring the online luminosity and beam background. Although the readout bandwidth of the Fast Beam Conditions Monitoring system (BCM1F one of the faster monitoring systems of the CMS BRIL), was sufficient for the initial LHC conditions, the foreseen enhancement of the beams parameters after the LHC Long Shutdown-1 (LS1) imposed the upgrade of the system. This paper presents the new BCM1F, which is designed to provide real-time fast diagnosis of beam conditions and instantaneous luminosity with readout able to resolve the 25 ns bunch structure.

The design and tests of front-end electronics for straw tube trackers in the PANDA experiment at FAIR are presented. The challenges for the front-end electronics, comprising operation at high counting rate up to 1MHz per straw tube, are discussed and the proposed architecture comprising a switched gain charge sensitive preamplifier (CSP), a pole-zero cancellation circuit (PZC), a second order variable peaking time shaper, a trimming ion tail cancellation circuit, and a baseline holder (BLH), is described. The front-end provides an analogue output and a discriminator with LVDS differential driver for the Time-of-Arrival (ToA) and Time-over-Threshold (ToT) measurements. A prototype readout ASIC featuring four channels was fabricated in 0.35 mu m CMOS technology consuming 15.5 mW (analog part) and 12 mW (LVDS) per channel. The results of measurements of peaking time (25-67 ns), gain, noise (ENC 800-2500 el. for various gains), time walk and jitter are presented as well as the first results obtained with prototype straw tubes connected.

The results of simulations for future measurements of electromagnetic form factors at \PANDA (FAIR) within the PandaRoot software framework are reported. The statistical precision at which the proton form factors can be determined is estimated. The signal channel $\bar p p \to e^+ e^-$ is studied on the basis of two different but consistent procedures. The suppression of the main background channel, i.e. the $\bar p p \to \pi^+ \pi^-$, is studied. Furthermore, the background versus signal efficiency, statistic and systematic uncertainties on the extracted proton form factors are evaluated using to the two different procedures. The results are consistent with those of a previous simulation study using an older, simplified framework. However, a slightly better precision is achieved in the PandaRoot study in a large range of momentum transfer, assuming the nominal beam condition and detector performances.

We present the design and the test results of the BCM1F front end ASIC designed for readout of diamond sensors used in the Beam Condition Monitoring system at the Compact Muon Solenoid (CMS) experiment built in the European Organization for Nuclear Research (CERN) in Geneva. The design comprises a fast transimpedance preamplifier with active feedback, a shaper stage and high-performance differential output buffer. The front end amplifier shows good linearity for input charges below 7 fC, signal gain of about 50 mV/fC, equivalent noise charge (ENC) around 400 e- for 2 pF and less than 700 e- for 5 pF input capacitance. The measured peaking time (Tp) is in the range from 6.6 to 9.4 ns depending on the applied bias conditions and the input capacitance. The full-width-at-half-maximum (FWHM) of the response is kept below 10 ns, which allows for efficient beam halo detection. The return time after the detector signal overdrive is maintained below 25 ns. These two latter parameters make the presented circuit compatible with high data rate applications.

We present the design and the test results of the BCM1F front end ASIC designed for readout of diamond sensors used in the Beam Condition Monitoring system at the Compact Muon Solenoid (CMS) experiment built in the European Organization for Nuclear Research (CERN) in Geneva. The design comprises a fast transimpedance preamplifier with active feedback, a shaper stage and high-performance differenti...

The CMS Beam Radiation Instrumentation and Luminosity (BRIL) project is composed of several systems providing the experiment protection from adverse beam conditions while also measuring the online luminosity and beam background. Although the readout bandwidth of the Fast Beam Conditions Monitoring system (BCM1F - one of the faster monitoring systems of the CMS BRIL), was sufficient for the initial LHC conditions, the foreseen enhancement of the beams parameters after the LHC Long Shutdown-1 (LS1) imposed the upgrade of the system. This paper presents the new BCM1F, which is designed to provide real-time fast diagnosis of beam conditions and instantaneous luminosity with readout able to resolve the 25 ns bunch structure.

The Fast Beam Conditions Monitor, BCM1F, in the Compact Muon Solenoid, CMS, experiment was operated since 2008 and delivered invaluable information on the machine induced background in the inner part of the CMS detector supporting a safe operation of the inner tracker and high quality data. Due to the shortening of the time between two bunch crossings from 50ns to 25ns and higher expected luminosity at the Large Hadron Collider, LHC, in 2015, BCM1F needed an upgrade to higher bandwidth. In addition, BCM1F is used as an on-line luminometer operated independently of CMS. To match these requirements, the number of single crystal diamond sensors was enhanced from 8 to 24. Each sensor is subdivided into two pads, leading to 48 readout channels. Dedicated fast front-end ASICs were developed in 130nm technology, and the back-end electronics is completely upgraded. An assembled prototype BCM1F detector comprising sensors, a fast front-end ASIC and optical analog readout was studied in a 5GeV electron beam at the DESY-II accelerator. Results on the performance are given.

The exclusive charmonium production process in $\bar{p}p$ annihilation with an associated $\pi^0$ meson $\bar{p}p\to J/\psi\pi^0$ is studied in the framework of QCD collinear factorization. The feasibility of measuring this reaction through the $J/\psi\to e^+e^-$ decay channel with the PANDA (AntiProton ANnihilation at DArmstadt) experiment is investigated. Simulations on signal reconstruction efficiency as well as the background rejection from various sources including the $\bar{p}p\to\pi^+\pi^-\pi^0$ and $\bar{p}p\to J/\psi\pi^0\pi^0$ reactions are performed with PandaRoot, the simulation and analysis software framework of the PANDA experiment. It is shown that the measurement can be done at PANDA with significant constraining power under the assumption of an integrated luminosity attainable in four to five months of data taking at the maximum design luminosity.

Baryon-to-meson Transition Distribution Amplitudes (TDAs) encoding valuable new information on hadron structure appear as building blocks in the collinear factorized description for several types of hard exclusive reactions. In this paper, we address the possibility of accessing nucleon-to-pion (πN) TDAs from \(\bar pp \to e^ + e^ - \pi ^0 \) reaction with the future P̄ANDA detector at the FAIR facility. At high center-of-mass energy and high invariant mass squared of the lepton pair q 2, the amplitude of the signal channel \(\bar pp \to e^ + e^ - \pi ^0 \) admits a QCD factorized description in terms of πN TDAs and nucleon Distribution Amplitudes (DAs) in the forward and backward kinematic regimes. Assuming the validity of this factorized description, we perform feasibility studies for measuring \(\bar pp \to e^ + e^ - \pi ^0 \) with the P̄ANDA detector. Detailed simulations on signal reconstruction efficiency as well as on rejection of the most severe background channel, i.e. \(\bar pp \to \pi ^ + \pi ^ - \pi ^0 \) were performed for the center-of-mass energy squared s = 5 GeV2 and s = 10 GeV2, in the kinematic regions 3.0 < q 2 < 4.3 GeV2 and 5 < q 2 GeV2, respectively, with a neutral pion scattered in the forward or backward cone \(\left| {\cos \theta _{\pi ^0 } } \right| > 0.5\) in the proton-antiproton center-of-mass frame. Results of the simulation show that the particle identification capabilities of the P̄ANDA detector will allow to achieve a background rejection factor of 5 · 107 (1 · 107) at low (high) q 2 for s = 5 GeV2, and of 1 · 108 (6 · 106) at low (high) q 2 for s = 10 GeV2, while keeping the signal reconstruction efficiency at around 40%. At both energies, a clean lepton signal can be reconstructed with the expected statistics corresponding to 2 fb−1 of integrated luminosity. The cross sections obtained from the simulations are used to show that a test of QCD collinear factorization can be done at the lowest order by measuring scaling laws and angular distributions. The future measurement of the signal channel cross section with P̄ANDA will provide a new test of the perturbative QCD description of a novel class of hard exclusive reactions and will open the possibility of experimentally accessing π TDAs.

The Beam Radiation Instrumentation and Luminosity Project of the CMS experiment consists of several beam monitoring systems and luminometers. The upgraded Fast Beam Conditions Monitor is based on 24 single crystal diamond sensors with a two-pad metallization and a custom designed readout. Signals for real time monitoring are transmitted to the counting room, where they are received and processed by new back-end electronics designed to measure count rates on LHC collision, beam induced background and activation products to be used to determine the luminosity and the machine induced background. The system architecture and the signal processing algorithms will be presented.

The CMS beam and radiation monitoring subsystem BCM1F during LHC Run I consisted of 8 individual diamond sensors situated around the beam pipe within the tracker detector volume, for the purpose of fast monitoring of beam background and collision products. Effort is ongoing to develop the use of BCM1F as an online bunch-by-bunch luminosity monitor. BCM1F will be running whenever there is beam in LHC, and its data acquisition is independent from the data acquisition of the CMS detector, hence it delivers luminosity even when CMS is not taking data. To prepare for the expected increase in the LHC luminosity and the change from 50 ns to 25 ns bunch separation, several changes to the system are required, including a higher number of sensors and upgraded electronics. In particular, a new real-time digitizer with large memory was developed and is being integrated into a multi-subsystem framework for luminosity measurement. Current results from Run II preparation will be shown, including results from the January 2014 test beam. Presented at TIPP2014 3rd International Conference on Technology and Instrumentation in Particle Physics, Upgraded Fast Beam Conditions Monitor for CMS online luminosity measurement Jessica Lynn Leonard*, Maria Hempel†, Hans Henschel, Olena Karacheban, Wolfgang Lange, Wolfgang Lohmann†, Roberval Walsh DESY Zeuthen, Germany E-mail:jessica.lynn.leonard@desy.de, maria.hempel@desy.de, hans.henschel@desy.de, olena.karacheban@desy.de, wolfgang.lange@desy.de, wolfgang.lohmann@desy.de, roberval.walsh@desy.de Anne Dabrowski, Vladimir Ryjov CERN Geneva, Switzerland E-mail: anne.evelyn.dabrowski@cern.ch, vladimir.ryjov@cern.ch David Stickland Princeton University Princeton, New Jersey, USA E-mail: david.peter.stickland@cern.ch The CMS beam and radiation monitoring subsystem BCM1F during LHC Run I consisted of 8 individual diamond sensors situated around the beam pipe within the tracker detector volume, for the purpose of fast monitoring of beam background and collision products. Effort is ongoing to develop the use of BCM1F as an online bunch-by-bunch luminosity monitor. BCM1F will be running whenever there is beam in LHC, and its data acquisition is independent from the data acquisition of the CMS detector, hence it delivers luminosity even when CMS is not taking data. To prepare for the expected increase in the LHC luminosity and the change from 50 ns to 25 ns bunch separation, several changes to the system are required, including a higher number of sensors and upgraded electronics. In particular, a new real-time digitizer with large memory was developed and is being integrated into a multi-subsystem framework for luminosity measurement. Current results from Run II preparation will be discussed, including results from the January 2014 test beam. Technology and Instrumentation in Particle Physics 2014 2-6 June, 2014 Amsterdam, the Netherlands * Speaker † Also at Brandenburg Technical University, Cottbus, Germany  Copyright owned by the author(s) under the terms of the Creative Commons Attribution-NonCommercial-ShareAlike Licence. http://pos.sissa.it BCM1F for CMS online luminosity Jessica Lynn Leonard 1. Overview of BCM1F The CMS Fast Beam Condition Monitor (BCM1F)[1] provides bunch-by-bunch information on the flux of beam halo and collision products passing through the inner CMS detector[2]. The system was originally designed to monitor the condition of the beam to ensure low enough tracker occupancy for data-taking. However, BCM1F's purpose has evolved to include fast measurement of luminosity in order to function as an online luminometer.

A stable reference voltage (or current) source is a standard component of today's microelectronics systems. In particle physics experiments such reference is needed in spite of harsh ionizing radiation conditions, i.e. doses exceeding 100 Mrads and fluences above 1e15 n/cm2. After such radiation load a bandgap reference using standard p-n junction of bipolar transistor does not work properly. Instead of using standard p-n junctions, two enclosed layout transistor (ELTMOS) structures are used to create radiation-hard diodes: the ELT bulk diode and the diode obtained using the ELTMOS as dynamic threshold transistor (DTMOS). In this paper we have described several sub-1V references based on ELTMOS bulk diode and DTMOS based diode, using CMOS 130 nm process. Voltage references the structures with additional PTAT (Proportional To Absolute Temperature) output for temperature measurements were also designed. We present and compare post-layout simulations of the developed bandgap references and temperature sensors, which show correct operation (<1mV bandgap stability, linear PTAT) in teperature range -20 to 100 celsius degree.

Detector-plane prototypes of the very forward calorimetry of a future detector at an e(+)e(-) collider have been built and their performance was measured in an electron beam. The detector plane comprises silicon or GaAs pad sensors, dedicated front-end and ADC ASICs, and an FPGA for data concentration. Measurements of the signal-to-noise ratio and the response as a function of the position of the sensor are presented. A deconvolution method is successfully applied, and a comparison of the measured shower shape as a function of the absorber depth with a Monte-Carlo simulation is given.

The PANDA spectrometer will be built at the FAIR facility at Darmstadt (Germany) to perform accurate tests of the strong interaction through ¯pp and ¯pA annihilation studies. The charged particle tracking at PANDA will be done using both solid state and gaseous detectors. Among the latter, two straw tube detector systems will be built [1]. The cylindrical, central straw tube tracker features a high spatial and momentum resolution for a wide range of particle momenta from about 8 GeV/c down to a few 100 MeV/c, together with particle identification in the momentum region below about 1 GeV/c by measuring the specific energy-loss. A new technique, based on self-supporting straw double layers with intrinsic wire tension developed for the COSY-TOF straw tracker [2], has been adopted for the PANDA trackers. The development of the readout electronics for the straw tubes is ongoing. Prototypes have been produced and used to instrument straw tube modules that have been tested with cosmic rays and proton beams. Design issues of the PANDA straw tubes, together with the results of the prototype tests are presented.

The Beam Radiation Instrumentation and Luminosity Project of the CMS experiment, consists of several beam monitoring systems. One system, the upgraded Fast Beams Condition Monitor, is based on 24 single crystal CVD diamonds with a double-pad sensor metallization and a custom designed readout. Signals for real-time monitoring are transmitted to the counting room, where they are received and processed by new back-end electronics designed to extract information on LHC collision, beam induced background and activation products. The Slow Control Driver is designed for the front-end electronics configuration and control. The system architecture and the upgrade status will be presented.