ThomX is a compact x-ray source based on Compton scattering, installed at IJCLab (Laboratoire de physique des 2 infinis-Irène Joliot-Curie) in Orsay. The machine uses a small electron storage ring and an intense laser pulse stored in a high-finesse optical cavity. This article describes the various subsystems of the machine and their initial results of the commissioning, which began in mid-2021. This first commissioning phase led to the production of 10^{10} x-rays/s with an on-axis energy of 45 keV. The main steps to be taken to reach the nominal flux are outlined at the end.

With the increase in laser power and finesse of optical cavities over the last decade, laboratory-size Compton sources are very promising. These sources produce X-rays through interactions between relativistic electrons and laser photons and, in term of brightness, fall between large synchrotron facilities and classical laboratory X-ray sources. The ThomX source is the French project in this field. This article first presents a state of the art of high-intensity Compton sources, then the ThomX source is briefly described, and the first results are detailed, in particular the production of the first X-rays, the acquisition of the first spectrum and the first image of the beam. Finally, the next objectives are discussed.

A multi-TeV muon collider offers a spectacular opportunity in the direct exploration of the energy frontier. Offering a combination of unprecedented energy collisions in a comparatively clean leptonic environment, a high energy muon collider has the unique potential to provide both precision measurements and the highest energy reach in one machine that cannot be paralleled by any currently available technology. The topic generated a lot of excitement in Snowmass meetings and continues to attract a large number of supporters, including many from the early career community. In light of this very strong interest within the US particle physics community, Snowmass Energy, Theory and Accelerator Frontiers created a cross-frontier Muon Collider Forum in November of 2020. The Forum has been meeting on a monthly basis and organized several topical workshops dedicated to physics, accelerator technology, and detector R D. Findings of the Forum are summarized in this report.

A special session at eeFACT’22 reviewed the electrical power budgets and luminosity risks for eight proposed future Higgs and electroweak factories (C 3 , CEPC, CERC, CLIC, FCC-ee, HELEN, ILC, and RELIC) and, in comparison, for a lepton-hadron collider (EIC) presently under construction. We report highlights of presentations and discussions.

In the LEMMA muon source proposal [1–3] a positron beam at 45 GeV is used to produce muons at threshold by interaction with some targets. In order to release the required intensity on the main positron source, orders of magnitude higher than the state of the art, the possibility to recover the primary positron beam after the interaction with the targets was studied. The particles distribution, with a strongly degraded energy spread after the interaction, was injected back into a low emittance, large energy acceptance 45 GeV ring. Studies of injection efficiency were performed. The possibility of compressing the beam in a linac before injection was also studied. As a result, even without compression, about 80% of the disrupted e+ beam can be injected back into the ring.

AbstractLattice design in the context we will describe it here is the design and optimization of the principle elements—the lattice cells—of a circular accelerator, and it includes the dedicated variation of the accelerator elements (as for example position and strength of the magnets in the machine) to obtain well defined and predictable parameters of the stored particle beam. It is therefore closely related to the theory of linear beam optics that has been described in Chap.10.1007/978-3-030-34245-6_2[1].

In response to the 2013 Update of the European Strategy for Particle Physics (EPPSU), the Future Circular Collider (FCC) study was launched as a world-wide international collaboration hosted by CERN. The FCC study covered an energy-frontier hadron collider (FCC-hh), a highest-luminosity high-energy lepton collider (FCC-ee), the corresponding 100km tunnel infrastructure, as well as the physics opportunities of these two colliders, and a high-energy LHC, based on FCC-hh technology. This document constitutes the third volume of the FCC Conceptual Design Report, devoted to the hadron collider FCC-hh. It summarizes the FCC-hh physics discovery opportunities, presents the FCC-hh accelerator design, performance reach, and staged operation plan, discusses the underlying technologies, the civil engineering and technical infrastructure, and also sketches a possible implementation. Combining ingredients from the Large Hadron Collider (LHC), the high-luminosity LHC upgrade and adding novel technologies and approaches, the FCC-hh design aims at significantly extending the energy frontier to 100TeV. Its unprecedented centre of-mass collision energy will make the FCC-hh a unique instrument to explore physics beyond the Standard Model, offering great direct sensitivity to new physics and discoveries.

In response to the 2013 Update of the European Strategy for Particle Physics, the Future Circular Collider (FCC) study was launched, as an international collaboration hosted by CERN. This study covers a highest-luminosity high-energy lepton collider (FCC-ee) and an energy-frontier hadron collider (FCC-hh), which could, successively, be installed in the same 100 km tunnel. The scientific capabilities of the integrated FCC programme would serve the worldwide community throughout the 21st century. The FCC study also investigates an LHC energy upgrade, using FCC-hh technology. This document constitutes the second volume of the FCC Conceptual Design Report, devoted to the electron-positron collider FCC-ee. After summarizing the physics discovery opportunities, it presents the accelerator design, performance reach, a staged operation scenario, the underlying technologies, civil engineering, technical infrastructure, and an implementation plan. FCC-ee can be built with today’s technology. Most of the FCC-ee infrastructure could be reused for FCC-hh. Combining concepts from past and present lepton colliders and adding a few novel elements, the FCC-ee design promises outstandingly high luminosity. This will make the FCC-ee a unique precision instrument to study the heaviest known particles (Z, W and H bosons and the top quark), offering great direct and indirect sensitivity to new physics.

The design of a future multi-TeV muon collider needs new ideas to overcome the technological challenges related to muon production, cooling, accumulation and acceleration. In this paper a layout of a positron driven muon source known as the Low EMittance Muon Accelerator (LEMMA) concept is presented. The positron beam, stored in a ring with high energy acceptance and low emittance, is extracted and driven to a multi-target system, to produce muon pairs at threshold. This solution alleviates the issues related to the power deposited and the integrated Peak Energy Density Deposition (PEDD) on the targets. Muons produced in the multi-target system will then be accumulated before acceleration and injection in the collider. A multi-target line lattice has been designed to cope with the focusing of both the positron and muon beams. Studies on the number, material and thickness of the targets have been carried out. A general layout of the overall scheme and a description is presented, as well as plans for future R&D.

In response to the 2013 Update of the European Strategy for Particle Physics (EPPSU), the Future Circular Collider (FCC) study was launched as a world-wide international collaboration hosted by CERN. The FCC study covered an energy-frontier hadron collider (FCC-hh), a highest-luminosity high-energy lepton collider (FCC-ee), the corresponding 100 km tunnel infrastructure, as well as the physics opportunities of these two colliders, and a high-energy LHC, based on FCC-hh technology. This document constitutes the third volume of the FCC Conceptual Design Report, devoted to the hadron collider FCC-hh. It summarizes the FCC-hh physics discovery opportunities, presents the FCC-hh accelerator design, performance reach, and staged operation plan, discusses the underlying technologies, the civil engineering and technical infrastructure, and also sketches a possible implementation. Combining ingredients from the Large Hadron Collider (LHC), the high-luminosity LHC upgrade and adding novel technologies and approaches, the FCC-hh design aims at significantly extending the energy frontier to 100 TeV. Its unprecedented centre-of-mass collision energy will make the FCC-hh a unique instrument to explore physics beyond the Standard Model, offering great direct sensitivity to new physics and discoveries.

The PADME experiment [1] aims at searching for the dark photon (A') in the e+ > Ay' process in a positron -on-target experiment, exploiting the positron beam of the DADNE Linac at the INFN Frascati National Laboratory (Italy). The Linac can provide a number of positrons in excess of 1010 in a 200 ns long pulse but, in order to keep the pile-up probability in the calorimeter at an acceptable level, the number of positrons for PADME has to be below 105/pulse, in particular by using the attenuating target in the BTF beam-line. The experiment is then essentially limited by the low duty factor (10-5=200 ns/20 ms). In this paper, an alternative proposal to use the DADNE positron ring as a Linac pulse stretcher, by injecting each pulse into the ring and extracting it by a slow resonant extraction using the m/3 resonance, is presented. This would allow for distributing the positrons of a single Linac pulse over a much longer time interval (0.2-0.5 ms), increasing the duty factor up to 1%. The required modifications of the DADNE positron transfer line and ring are described. A dedicated lattice for the positron ring has been designed and tracking of the positrons injected in the ring has been performed in order to optimize the extraction parameters and to give a preliminary estimate of the extracted beam characteristics.

We are studying a novel scheme to produce muon beams characterised by very low emittance, thus allowing to avoid the need for cooling, using a positron beam of about 45 GeV interacting on electrons on a fixed target. This is a challenging scheme, and a full design study has to be developed. One of the key innovative topics to be investigated regards the interaction between the positron beam stored in a low emittance ring with a thin target inserted directly in the ring cham- ber. Produced muons will then be immediately collected at the exit of the target and transported to two μ+ and μ− accumulator rings. In this paper, after an introduction highlighting the rational in designing a muon collider, we discuss in detail this new muon production scheme, covering the simulation of the e+ beam interacting with the target, its degradation in the 6-D phase space and the optimisation of the e+ ring design mainly to maximise the energy acceptance.

To improve collaborative studies on beam dynamics for SuperKEKB between several labs, efforts have been made to translate the SAD lattices of SuperKEKB rings to the versions for other codes: AT, Bmad, MAD-X, and PTC. It turns out that lattice translations between these codes are not straightforward because of the complexity of the SuperKEKB lattices. In this paper, we describe our experiences of lattice translations, and present some results of benchmarks for the case of SuperKEKB.

The energy upgrade of the SPARC_LAB photo-injector at LNF-INFN (Frascati, Italy) has been originally conceived replacing one low gradient (13MV/m) 3m long SLAC type S-band traveling wave (TW) section with two 1.4m long C-band accelerating sections. Due to the higher gradients reached by such structures, a higher energy beam can be obtained within the same accelerator footprint length. The use of C-band structures for electron acceleration has been adopted in a few FEL linacs in the world, among others, the Japanese Free Electron Laser at SPring-8 and the SwissFEL at Paul Scherrer Institute (PSI). The C-band sections are traveling wave, constant impedance structures with symmetric input and output axial couplers. Their design has been optimized for the operation with a SLED RF pulse compressor. In this paper we briefly review their design criteria and we focus on the construction, tuning, low and high-power RF tests. We also illustrate the design and realization of the dedicated low level RF system that has been done in collaboration with PSI in the framework of the EU TIARA project. Preliminary experimental results appear to confirm the operation of such structures with accelerating gradients larger than 35MV/m.

After a long preparatory phase, including a wide hardware consolidation program, the Italian lepton collider DAFNE, is now systematically delivering data to the KLOE-2 experiment. In approximately 200 days of operation 1 fb-1 has been given to the detector limiting the background to a level compatible with an efficient data acquisition. Instantaneous and maximum daily integrated luminosity measured, so far, are considerably higher with respect to the previous KLOE runs, and are: L(inst) ~ 2.0 1032 cm-2s-1, and L(day) ~ 12.5 pb-1 respectively. A general review concerning refurbishing activities, machine optimization efforts and data taking performances is presented and discussed.

A τ/charm Factory, an e + e- collider with very high luminosity at the 2–4.6 GeV center of mass energy, to be built on the Rome University at Tor Vergata campus, was studied by the Consortium Nicola Cabibbo Laboratory and the INFN Frascati Laboratories. This project is the natural evolution of the flagship Italian project SuperB Factory, funded by the Italian Government in 2010 with a budget that turned out to be insufficient to cover the total costs of the project. The study of rare events at the τ/charm energy was already planned as a Phase-II of SuperB [1]. This design keeps all the unique features of SuperB, including the polarization of the electron beam, with the possibility to take data in a larger energy range, with reduced accelerator dimensions and construction and operation costs. A Report on the accelerator design has been published in September 2013 [2].