AbstractThe Hewlett Packard Enterprise–Cray EX Frontier is the world’s first and fastest exascale supercomputer, hosted at the Oak Ridge Leadership Computing Facility in Tennessee, United States. Frontier is a significant electricity consumer, drawing 8–30 MW; this massive energy demand produces significant waste heat, requiring extensive cooling measures. Although harnessing this waste heat for campus heating is a sustainability goal at Oak Ridge National Laboratory (ORNL), the 30 °C–38 °C waste heat temperature poses compatibility issues with standard HVAC systems. Heat pump systems, prevalent in residential settings and some industries, can efficiently upgrade low-quality heat to usable energy for buildings. Thus, heat pump technology powered by renewable electricity offers an efficient, cost-effective solution for substantial waste heat recovery. However, a major challenge is the absence of benchmark data on high-performance computing (HPC) heat generation and waste heat profiles. This paper reports power demand and waste heat measurements from an ORNL HPC data centre, aiming to guide future research on optimizing waste heat recovery in large-scale data centres, especially those of HPC calibre.

Data centers are energy -intensive facilities with substantial low-grade waste heat. High -temperature heat pumps can be critical in boosting the data center's waste heat for district heating, improving the system -level energy efficiency of data centers, and reducing CO2 emissions in district heating. This study built thermodynamic models to assess high -temperature heat pumps with six configurations using low global warming potential refrigerants to supply heat up to 120 degrees C. The heat pump configurations include single -stage or two -stage cycles with advanced components, such as internal heat exchanger, economizer, flash tank, or parallel compressor. The refrigerants include R1234ze(Z), R1233ed(E), R1224yd(Z), R600, and R600a, and R245fa is used as a reference. A case study was carried out to recover the waste heat from the Frontier high-performance computing data center and provide hot water for district heating at the US Department of Energy's Oak Ridge National Laboratory campus. The optimized performance of high -temperature heat pumps is characterized with various effectiveness of internal heat exchangers, and the operating parameters of economizer or flash tank, as well as their combination. The results show that the configurations of two -stage cycles with internal heat exchanger + flash tank and internal heat exchanger + economizer/parallel-compressor provide the highest coefficient of performance under scenarios of the maximum allowable value and a fixed value (0.3) of the internal heat exchangers' effectiveness, respectively. R1234ze(Z) and R600a are the most promising refrigerants, considering trade-offs between the coefficient of performance and the volumetric heating capacity. The single -stage cycle with internal heat exchanger + economizer/parallel-compressor using R1234ze(Z) is recommended for utilizing Fronter's waste heat in district heating. A one mega -watt high -temperature heat pump will reduce 33,100-33,200 metric tons of CO2 emission annually, corresponding to 85.4 %-85.6 % of equivalent CO2 emissions from natural gas boilers. This study provides good guidelines for designing and deploying high -temperature heat pumps to support sustainable data centers and decarbonize district heating in the US.

To understand how the composition of novel lubricant additives and their ash interact with gasoline particulate filters (GPFs), an accelerated aging protocol was conducted using three lubricant additive formulations and two GPF types. The additive packages (adpaks) consisted of Ca+Mg detergent in a 3:1 or 0:1 ratio and an anti-wear component—either zinc dialkyl dithiophosphate (ZDDP) or a novel phosphonium-phosphinate ionic liquid (IL) substitute. The particulate sampling captured amount/compositions of particulate matter (PM) generated, total particulate number, and size distribution. Five ash loadings were completed. GPF position and adpak composition affected the backpressure, ash composition, ash morphology, and captured mass. The particulate sampling indicated that the ash component consisted primarily of particles less than 50 nm in size and that the Mg-only adpak resulted in more particulate of 50–400 nm in size. Postmortem materials characterization indicated GPFs in the underfloor position had deeper penetration of ash into the walls compared to the close-coupled position. Additionally, the Mg-only adpak had a higher filter collection efficiency (>90%) and the ash particles consisted of a higher concentration of dense ash material. In contrast, four of the 3:1 Ca:Mg lubricant adpaks resulted in a collection efficiency of only 40–50%. Although the collection efficiency was higher with the Mg-only adpak, the ash layer in the GPF was not thicker, nor was the penetration into the wall more significant, and surprisingly the full useful life (FUL) backpressure was lower than with Ca:Mg adpaks. The higher density of the Mg-derived ash was the only detectable difference. A possible explanation of this observation is that Mg ash has a lower melting point and is more susceptible to densification during combustion or GPF regeneration. The substitution of IL in place of the ZDDP did not lead to any notable changes in collection efficiency or location of the ash.

With increasingly stringent regulations mandating the improvement of vehicle fuel economy, automotive manufacturers face growing pressure to develop and implement technologies that improve overall system efficiency. One such technology is an automatic (auto) stop-start feature. Auto stop-start reduces idle time and reduces fuel use by temporarily shutting the engine off when the vehicle comes to a stop and automatically re-starting it when the brake is released, or the accelerator is pressed. As mandated by the U.S. Congress, the U.S. Environmental Protection Agency (EPA) is required to keep the public informed about fuel saving practices. This is done, in partnership with the U.S. Department of Energy (DOE), through the fueleconomy.gov website. The “Fuel-Saving Technologies” and “Gas Mileage Tips” sections of the website are focused on helping the public make informed purchasing decisions and encouraging fuel-saving driving habits. In order to provide users with accurate information about the auto stop-start feature, experiments were conducted to determine its fuel economy effect. Four vehicles were tested both with and without the feature enabled under three test cycles: the Federal Test Procedure (FTP) city fuel economy test, the US06 high acceleration aggressive driving schedule that is often identified as the “Supplemental FTP” driving schedule, and the EPA New York City Cycle (NYCC). The results were compared to measure the fuel economy and consumption effects of using the auto stop-start feature. It was found that the fuel economy improvement varied significantly between drive cycles depending on the amount and percentage of idle time during the test. The largest fuel economy improvements were 7.27% and 26.4% for the FTP and NYCC, respectively.

Cold-start emissions remain a barrier to vehicle emissions targets and the race to zero impact emissions. Current aftertreatment catalysts are highly efficient once active but struggle at lower temperatures encountered during a cold-start. Significant research can be found on controlling cold-start NOx emissions with fewer studies on the closely linked hydrocarbon (HC) and particulate matter (PM) emissions. This study provides a detailed char-acterization of HC and PM emissions during cold-start transients to facilitate the development of emissions control technologies for cold-start emissions reduction. To fill this knowledge gap, cumulative and time-resolved speciation of the HC composition and particulate particle size over the initial 250s of the FTP-75 drive cycle were investigated. Emissions from both a turbocharged (t-GDI) and a naturally aspirated (na-GDI) vehicle were compared to capture the range of emissions that cold-start trapping technologies might encounter across different engine architectures. While cumulative emissions were found to be similar, time-resolved measure-ments show HC composition and particle sizing varied during the cold-start.

The U.S. Department of Energy’s Co-Optima initiative simultaneous focused on diversifying fuel sources, improving efficiency, and reducing emissions through using novel combustion strategies and sustainable fuel blends. For medium-duty/heavy-duty diesel engines, research in this area has led to the development of a multimode strategy that uses premixed charge compression ignition (PCCI) at low loads and conventional diesel combustion (CDC) at mid–high loads. The aim of this study was to understand how emissions were impacted when using PCCI instead of CDC at low loads and switching to an oxygenated biofuel blend. It provides a detailed speciation of the hydrocarbon (HC) and particulate matter (PM) emissions from a multimode medium-duty engine operating at low loads in PCCI and CDC modes and high loads in CDC. The effect of the oxygenated biofuel blend on emissions was studied at all three mode–load conditions using #2 ULSD and a bio-derived fuel (25% hexyl hexanoate (HHN)) blended in #2 ULSD. The PCCI mode effectively decreased NOx, total HC, and PM/PN emissions, with a substantial decrease in larger particles (≥50 nm). A PM/PN reduction was observed at high loads with the 25% HHN fuel. While the total HC emissions were not impacted by fuel type, the detailed HC analysis exposed changes in the HC’s composition.

Evaluating efficiency and security of Connected and Autonomous Vehicles (CAVs) requires an environment that can support applications and measurements under real-world conditions. This work introduces our implementation and evaluation of a Connected and Autonomous Vehicle Research Environment (CAVRE). We implement and evaluate an existing CAV application called Cooperative Adaptive Cruise Control (CACC) using physical Vehicle-to-Vehicle (V2V) communications between a virtual agent and a real autonomous vehicle operating on a steerable dynamometer. CAVRE allows the follower to autonomously control longitudinal behavior on the dynamometer in order to maintain a steady following time gap from the leader. The effects of a wireless jamming attack on CACC and fuel efficiency is also evaluated. By executing attacks in a controlled environment, we learn how compromised communications can degrade CAV applications. We show that jamming V2V communications can impact CACC’s string stability and decrease fuel efficiency by more than 50%.

Increased energy consumption from autonomous vehicle (AV) sensors and computational load as well as upfront costs of sensors are barriers to broad AV adoption. For high quality and reliable perception of the driving environment, incoming data from multiple sensors need to be fused together using advanced computational algorithms, which requires a high compute load. As an alternative, infrastructure-based sensors can be designed to facilitate perception and sensing by supporting vehicle-to-infrastructure (V2I) information exchange. This work presents the initial development and evaluation of a novel energy efficient infrastructure-based sensor. The sensor, a chip-enabled raised pavement marker (CERPM), is capable of wireless communications to exchange environment information with AVs. As a test case, the developed CERPM is applied in real-world driving to perform lane line and drivable region detection for an AV. It is shown that CERPMs can be utilized to effectively detect the lane line and drivable region, which can improve perception while reducing the compute load.

Commercialization of autonomous vehicle technology is a major goal of the automotive industry, thus research in this space is rapidly expanding across the world. However, despite this high level of research activity, literature detailing a straightforward and cost-effective approach to the development of an AV research platform is sparse. To address this need, we present the methodology and results regarding the AV instrumentation and controls of a 2019 Kia Niro which was developed for a local AV pilot program. This platform includes a drive-by-wire actuation kit, Aptiv electronically scanning radar, stereo camera, MobilEye computer vision system, LiDAR, inertial measurement unit, two global positioning system receivers to provide heading information, and an in-vehicle computer for driving environment perception and path planning. Robotic Operating System software is used as the system middleware between the instruments and the autonomous application algorithms. After selection, installation, and integration of these components, our results show successful utilization of all sensors, drive-by-wire functionality, a total additional power* consumption of 242.8 Watts (*Typical), and an overall cost of $118,189 USD, which is a significant saving compared to other commercially available systems with similar functionality. This vehicle continues to serve as our primary AV research and development platform.

The use of fuel reformate from catalytic processes is known to have beneficial effects on the spark-ignited (SI) combustion process through enhanced dilution tolerance and decreased combustion duration, but in many cases reformate generation can incur a significant fuel penalty. In a previous investigation, the researchers showed that, by controlling the boundary conditions of the reforming catalyst, it was possible to minimize the thermodynamic expense of the reforming process, and in some cases, realize thermochemical recuperation (TCR), a form of waste heat recovery where exhaust heat is converted to usable chemical energy. The previous work, however, focused on a relatively light-load engine operating condition of 2000 rpm, 4 bar brake mean effective pressure (BMEP). The present investigation demonstrates that this operating strategy is applicable to higher engine loads, including boosted operation up to 10 bar BMEP. By controlling the reforming catalyst boundary conditions, it is possible to achieve fuel reforming without experiencing high temperature exotherms that could be damaging to the catalyst. Additionally, the thermodynamic air handling consequences of operating a highly dilute strategy at high loads is quantified. The results confirm that this operating strategy provides an efficiency benefit at all conditions investigated, with relative efficiency increases of 3-6%, and is therefore applicable over wider regions of the engine operating map.

Battery electric vehicles (BEVs) are a critical pathway towards achieving energy independence and meeting greenhouse and criteria pollutant gas reduction goals in the current and future transportation sector. Emerging connected and automated vehicle (CAV) technologies further open the door for developing innovative applications and systems to leverage vehicle efficiency and substantially transform transportation systems. Therefore, we present a simulation study of various BEV types and compare the performance when driving on real-road drive cycles to highly optimized eco-driving cycles using advanced CAV technologies. The results demonstrate that eco-driving has a high potential to reduce energy consumption for all types of BEVs considered. The investigated BEVs include a compact vehicle, a transit city bus, and a Class 7 delivery truck. The impact of eco-driving on conventional vehicles was also compared to comparable BEVs. Compared to the BEVs, eco-driving provides a larger reduction in the conventional vehicle's braking energy loss, and also provides conventional vehicles with greater reductions in the engine mechanical energy output but the fuel savings did not show a consistent trend among all the conventional vehicle types. As part of the study, a comprehensive EV powertrain model was developed to account for key EV components and powertrain configurations.

The purpose of this work is to record the baseline performance of a state-of-the-art micro-combined heat and power (mCHP) system. A second goal of this work is to provide detailed thermodynamic first and second law performance measurements of the internal combustion engine and generator subsystems. A global technology survey was conducted to identify the leading mCHP systems in the 1 kW electric range. The Honda ECOWILL was identified as the state-of-the-art system in the United States, and an unused unit was procured. The ECOWILL underwent round-robin performance testing at three independent laboratories. First law (energy) and second law (exergy) analyses were conducted on the steady state data. Analysis revealed the ECOWILL operated at a first law electrical efficiency of 23.5 +/- 0.4% and a utilization factor of 74.5 +/- 3.2%. The primary energy loss was heat transfer from the device, followed by chemical and thermal energy in the exhaust stack. The second law analysis showed the ECOWILL operated at a second law electrical efficiency of 23.1 +/- 0.4% and total (including exergy in both the electrical and recovered waste heat streams) second law efficiency of 30.2 +/- 2.3%. Key areas of exergy destruction were, in decreasing magnitude, heat transfer, combustion irreversibility, and generator and friction losses.

In 2016, the Vehicle Technologies Office (VTO) of the Department of Energy (DOE) issued a solicitation for the AOP Lab Call research in FY2017 on a number of topics related to vehicles. Topic 6A of the Lab Call focused on research related to advanced lubricants: "…(in) support of the lubricants program goal to, by 2020, demonstrate novel formulations for powertrain and driveline lubricants, compatible with new and legacy vehicles, to achieve at least a 4 percent real-world fuel economy improvement." Argonne National Laboratory (ANL) in collaboration with Oak Ridge National Laboratory (ORNL) and Pacific Northwest National Laboratory (PNNL) was awarded a 3-year multilab project on "Lubricant Technology - Innovation, Discovery, Design, and Engineering." Research on the project began in FY2017 at the three laboratories with industry participation; however, in FY2018, the project was terminated due to budgetary constraints. The following is the final report for the project and highlights progress made during the first year of research. The report is divided into sections that highlight the following: Goals, objectives, milestones and deliverables, project highlights, outreach – publications, conferences, and reports, milestones accomplished, and research progress.

Vehicle manufacturers are developing and introducing new technologies to improve fuel economy and reduce vehicle carbon dioxide (CO2) emissions to comply with increasingly challenging regulations. Despite growing interest in electric vehicles, spark-ignition (SI) engines dominate the light-duty market in the U.S. and are expected to re main in wide use for decades. There is growing interest in making use of fuels with increased octane number to help improve engine efficiency through increased compression ratio, downsizing with turbocharging, and downspeeding. Regular gasoline in the U.S. is generally rated at 87 AKI (anti-knock index), where the AKI is defined as the a verage of the Research Octane Number1 (RON) and the Motor Octane Number2 (MON).

Aggressive driving is an important topic for many reasons, one of which is higher energy used per unit distance traveled, potentially accompanied by an elevated production of greenhouse gases and other pollutants. Examining a large data set of self-reported fuel economy (FE) values revealed that the dispersion of FE values is quite large and is larger for hybrid electric vehicles (HEVs) than for conventional gasoline vehicles. This occurred despite the fact that the city and highway FE ratings for HEVs are generally much closer in value than for conventional gasoline vehicles. A study was undertaken to better understand this and better quantify the effects of aggressive driving, including reviewing past aggressive driving studies, developing and exercising a new vehicle energy model, and conducting a related experimental investigation. The vehicle energy model focused on the limitations of regenerative braking in combination with varying levels of driving-style aggressiveness to show that this could account for greater FE variation in an HEV compared to a similar conventional vehicle. A closely matched pair of gasoline-fueled sedans, one an HEV and the other having a conventional powertrain, was chosen for both modeling and chassis dynamometer experimental comparisons. Results indicate that the regenerative braking limitations could be a main contributor to the greater HEV FE variation under the range of drive cycles considered. The complete body of results gives insight into the range of fuel use penalties that results from aggressive driving and why the variation can be larger on a percent basis for an HEV compared to a similar conventional vehicle, while the absolute fuel use penalty for aggressive driving is generally larger for conventional vehicles than HEVs.

In the current work, a series hybrid vehicle has been constructed that utilises a dual-fuel, reactivity controlled compression ignition (RCCI) engine. Full vehicle testing was conducted on chassis dynamometers over the US Environmental Protection Agency Federal Test Procedure, Highway Fuel Economy Test and US06 using RCCI combustion with commercially available gasoline and ultra-low sulphur diesel. Fuel economy and emissions data were recorded over the specified test cycles. Testing revealed that engine-out emissions were similar to steady-state dynamometer engine testing. However, tailpipe-out emissions saw a reduction of HC and CO during the HWFET of 98.5%. Fuel economy was lower than expected due to the higher drivetrain losses of the series hybrid drivetrain. Finally, simulated changes to the drivetrain showed that it may be possible to increase fuel economy significantly, while meeting EPA emissions standards.