We study how nitridation, applied to SiON gate layers, impacts the reliability of planar metal-oxide-semiconductor field effect transistors (MOSFETs) subjected to negative and positive bias temperature instability (N/PBTI) as well as hard breakdown (HBD) characteristics of these devices. Experimental data demonstrate that p-channel transistors with SiON layers characterized by a higher nitrogen concentration have poorer NBTI reliability compared to their counterparts with a lower nitrogen content, while PBTI in n-channel devices is negligibly weak in all samples independently of the nitrogen concentration. The Weibull distribution of HBD fields extracted from experimental data in devices with a higher N density are shifted towards lower values with respect to that measured in MOSFETs, and SiON films have a lower nitrogen concentration. Based on these findings, we conclude that a higher nitrogen concentration results in the aggravation of BTI robustness and HBD characteristics.

The present study reports the impact of process conditions and post annealing treatment on the stress and physico-chemical properties in different types of plasma enhanced atomic layer deposited (PEALD) SiNx films. More specifically, the SiNx films deposited at 500 °C were annealed subsequently at 1000 °C in N2 ambient for different times ranging between 30 and 6750 s and were subjected to thickness, mass, refractive index, chemical bonds and structure, H content, N/Si stoichiometry, morphology, roughness, and uniformity monitoring. Depending on the deposition process conditions, we confirm the possibility to form, at 500 °C with PEALD, some very compressive SiN films with reduced hydrogen content by controlling the plasma conditions along the deposition process. More interestingly, these compressive films with low hydrogen concentration exhibit high thermo-mechanical stability compared to hydrogenated PEALD and plasma enhanced chemical vapor deposition silicon nitride from this study or reported in the literature, films which typically tend to become tensile with a similar annealing sequence. These results confirm the importance of the plasma power to engineer the as-deposited silicon nitride stress but also highlight the role of hydrogen in the thermal instability of these layers, a low H concentration being needed for a better mechanical stability.

The steam oxidation of SiGe shows a transition from Si-like to Ge-like oxidation behavior depending on Ge concentration and oxidation temperature. Ge-like oxidation is described by the generation of oxygen vacancies (VO) at the interface between the oxide and SiGe virtual substrate. [1] Due to the different oxidation behavior, the presence of a Ge-oxide-free interfacial layer (IL) can suppress SiGe oxidation. [2] Here we show how a passivating interfacial layer can be grown using low-pressure oxidation and highlight the importance of SiGe surface preparation prior to low-pressure oxidation.

In this study, we explored the key properties and functionalities of plasma enhanced atomic layer deposition (PEALD) SiNx films, synthesized using different deposition temperatures (500–550 °C) and plasma conditions (lower and higher), both on 300 mm blanket Si and on several integrated 3D topology substrates, at the thicknesses relevant for diverse nanoscale applications. Our study shows that with an increase of temperature (500–550 °C), a small reduction in HF wet etch rate (1.1–0.69 nm/min), and H content (9.6% vs 7.4%) was observed. When using higher plasmas, significant improvements in blanket properties were observed. The films were denser (2.95 g/cm3), exhibited lower H content (2.4%), showed better etch rates (0.39 and 0.44 nm/s for HF and CF4 based), and SiNx grew without any nucleation delay on alternative Si1−xGex channel surfaces. The vertical and lateral conformality was found to be similar and appears not to be impacted with the plasma conditions. Extensive steam oxidation barrier studies performed at the sidewalls of different aspect ratio lines showed the PEALD SiNx liner scaling potentiality down to 1 nm when deposited using higher plasma. In addition, the outer gate and inner spacer properties were found to be superior (with lower loses) for higher plasma films when subjected to several dry etch, strips, and H3PO4 chemistries. The outstanding conformality (90%–95% on aspect ratios ≤10:1) combined with excellent high end material properties in the ultrathin regimes (1–10 nm) corroborate the virtue of PEALD SiNx toward integration in scaled down and advanced nanoelectronics device manufacturing.