Abstract Body core temperature (Tc) monitoring is crucial for minimizing heat injury risk. However, validated strategies are invasive and expensive. Although promising, aural canal temperature (Tac) is susceptible to environmental influences. This study investigated whether incorporation of external auricle temperature (Tea) into an ear-based Tc algorithm enhances its accuracy during multiple heat stress conditions. Twenty males (mean ± SD; age = 25 ± 3 years, BMI = 21.7 ± 1.8, body fat = 12 ± 3%, maximal aerobic capacity (VO2max) = 64 ± 7 ml/kg/min) donned an ear-based wearable and performed a passive heating (PAH), running (RUN) and brisk walking trial (WALK). PAH comprised of immersion in hot water (42.0 ± 0.3 °C). RUN (70 ± 3%VO2max) and WALK (50 ± 10%VO2max) were conducted in an environmental chamber (Tdb = 30.0 ± 0.2 °C, RH = 71 ± 2%). Several Tc models, developed using Tac, Tea and heart rate, were validated against gastrointestinal temperature. Inclusion of Tea as a model input improved the accuracy of the ear-based Tc algorithm. Our best performing model (Trf3) displayed good group prediction errors (mean bias error = − 0.02 ± 0.26 °C) but exhibited individual prediction errors (percentage target attainment ± 0.40 °C = 88%) that marginally exceeded our validity criterion. Therefore, Trf3 demonstrates potential utility for group-based Tc monitoring, with additional refinement needed to extend its applicability to personalized heat strain monitoring.

Millettia speciosa Champ, renowned for its diverse applications in traditional medicine, is extensively cultivated in the Guangxi region of China, spanning roughly 5,973 hectares. In July 2021, a plantation in Yulin, Guangxi, China (22°64'N; 110°29'E), exhibited severe leaf spot disease on M. speciosa. Notably, a 46,690 square meters area had over 40% leaf spot incidence. Initially, symptoms appeared as small, circular, pale-yellow lesions on the leaves, then turned into irregular, dark brown spots with yellow halos, leading to the wilt and defoliation of leaves. To identify the responsible pathogen, a total of five symptomatic leaves were collected and sterilized systematically. Small tissue segments (5×5 mm) from lesion peripheries were aseptically excised, then surface sterilized with 75% ethanol for 10 s, and 1% sodium hypochlorite (NaClO) for 3 min. Following this, the sterilized tissues were triple-rinsed with sterile water and cultured on potato dextrose agar (PDA) at 28 °C in the dark for 7 d. A total of seven isolates were obtained through single-spore isolation, and one representative isolate, N2-3, was selected for further analysis. After 7 d of incubation, colonies displayed flat, white, and extensively branched aerial hyphae. Over time, the reverse side of the colony changed from white to yellowish-white. The pycnidia were black with conidial droplets ranging from cream to pale yellow exuding from their ostioles. The α-conidia were one-celled, hyaline, ovoid to cylindrical, typically with one or two droplets, 2.6 to 5.9 ×1.4 to 3.9 μm (n=50). These morphological traits align with those of the genus Diaporthe, as reported by Li et al. (2022) and Crous et al. (2015). To identify the species, isolate N2-3 underwent sequencing of the internal transcribed spacer (ITS), β-tubulin (BT), and translation elongation factor 1 alpha (EF1-α) sections (Huang et al. 2021). Obtained sequences of ITS, BT and EF1-α (Genebank accessions nos. OR600532, OR662169 and OR662168) displayed a 99% similarity to Diaporthe tulliensis (Genebank accessions nos. OP219651, ON932382, OL412437, respectively). Based on the concatenated ITS, BT and EF1-α, a neighbor-joining phylogenetic analyses using MEGA7.0 clustered with D. tulliensis. Therefore, the fungus was identified as D. tulliensis (teleomorph name) based on morphological and molecular features. A pathogenicity test was conducted on 1-year-old M. speciosa seedlings by gently abrading healthy leaves with sterilized toothpicks to create superficial wounds. Wounded leaves were then inoculated with 5 mm diameter mycelial plugs, while control seedlings received PDA plugs. Three leaves per plant and five plants per treatment were selected for assessment. All seedlings were kept in a controlled greenhouse (12/12h light/dark, 25 ± 2 °C, 90% humidity). After 7 d, the inoculated leaves showed symptoms like those in the field, while control plants remained healthy. The fungus was consistently reisolated from the infected leaves, satisfying Koch's postulates. Notably, D. tulliensis has caused Boston ivy leaf spot, bodhi tree leaf spot, cacao pod rot, and jasmine stem canker (Huang et al. 2021; Li et al. 2022; Serrato-Diaz et al. 2022; Hsu et al. 2023). This discovery is significant as it marks the first report of Diaporthe tulliensis causing leaf spot on Millettia speciossa in China, which has direct implications for the development of diagnostic tools and research into potential disease management strategies.

Nanhaia speciosa, commonly known as Niudali, is a medicinal woody vine belonging to the Leguminosae family. Valued for its culinary and medicinal properties, it is extensively cultivated, covering approximately 5,973 hm2 in the Guangxi Zhuang Autonomous Region of China. The edible tubers of this plant are reported to possess antibacterial and antioxidant effects (Luo et al., 2023; Shu et al., 2020). In July 2021, a Niudali plantation in Yulin, Guangxi, China (22°64'N; 110°29'E) exhibited leaf spot symptoms, with an incidence rate exceeding 40% across a 46,690 m2 area. Initially, small circular, pale yellow spots appeared on the leaves, which subsequently evolved into dark brown lesions surrounded by yellow halos, ultimately leading to foliage wilting. Leaves exhibiting typical symptoms were collected for pathogen investigation. The leaves were thoroughly washed with sterile water and small tissue fragments (5×5 mm) were excised from the lesion periphery. These fragments were surface-sterilized with 75% ethanol and 1% NaClO, rinsed three times with sterile water, and subsequently cultured on potato dextrose agar (PDA) at 28 °C in darkness for 7 days. Through single-spore isolation, seven isolates with similar morphological traits were obtained. After 7 days of incubation on PDA at 28 °C in dark, the colonies exhibited a white to grey coloration on the upper surface with abundant aerial hyphae, while the underside appeared dark black. The conidia, cylindrical or obclavate in shape, were straight, pale brown, and measured 30.1-128.9 μm × 4.8-15.0 μm (n=50). The morphological characteristics matched those of Corynespora sp.(Wang et al. 2021). For molecular identification, the isolate N5-2 underwent DNA sequence analysis using genomic DNA and primers ITS1/ITS4 and EF1-688F/EF1-1251R. The sequences (ITS: OP550425; TEF1-α: OQ117118) were deposited in GenBank, exhibiting 98% identity to C. cassiicola (OP981637) for TEF1-α and 99% homology to C. cassiicola (OP957070) for ITS. Based on the concatenated ITS and TEF1-α, a maximum likelihood phylogenetic analyses using MEGA7.0 clustered the isolate with C. cassiicola. Consequently, the fungus was identified as C. cassiicola based on its morphological and molecular features. In the pathogenicity test on 1-year-old Nanhaia speciosa seedlings, leaves were gently scratched and inoculated with mycelial plugs (5 mm). Control seedlings received PDA plugs. Five leaves per plant and five plants per treatment were selected for assessment. All seedling were maintained in a greenhouse (12/12h light/dark cycle, 25 ± 2°C, 90% humidity). After a 7-day incubation period, all leaves subjected to fungal inoculation exhibited symptoms consistent with those observed in the field, while control plants remained symptom-free. The fungus was successfully reisolated from the infected leaves in three successive trials, fulfilling Koch's postulates. While C. cassiicola is well-documented for inducing leaf spots on various plant species, including Jasminum nudiflorum, Strobilanthes cusia, Acanthus ilicifolius, Syringa species (Hu et al., 2023; Liu et al., 2023; Xie et al., 2021; Wang et al., 2021), this study represents the first report of C. cassiicola causing leaf spots on Nanhaia speciosa in China. The identification of this pathogen in Nanhaia speciosa has significant implications for future epidemiological investigations and serves as a valuable reference for controlling leaf spot disease in Nanhaia speciosa.

Strain WZ-12, isolated from the rhizosphere soil of star anise trees, exhibits significant antifungal efficacy against a variety of fungi, including Colletotrichum horii, the pathogenic fungus responsible for anthracnose in star anise. Based on 16S rRNA gene sequencing and phylogenetic analysis, the strain was identified as a member of the Streptomyces genus. The genome of WZ-12 comprises a linear chromosome of 9,169,400 bp and a plasmid of 378,325 bp, possessing a G + C content of 71.12%. Of note, the genome encompasses 8,172 protein-coding genes, 21 rRNA genes, 74 tRNA genes, and 89 other noncoding RNA genes. The COG, Swiss-Prot, GO, KEGG, and NR databases annotated up to 79.17, 50.50, 13.17, 37.51, and 90.43% of potential genes, respectively. Remarkably, the genome hosts 175 antimicrobial resistance genes and 33 secondary metabolite gene clusters that likely contribute to the biosynthesis of diverse bioactive compounds such as antibiotics and agents with antitumor, antioxidant, immunosuppressive, anti-inflammatory, or stress tolerance properties. These findings highlight the potential of WZ-12 as a promising source of novel bioactive molecules and suggest its significant value as a resource for developing innovative antimicrobial agents. [Formula: see text] Copyright © 2024 The Author(s). This is an open access article distributed under the CC BY-NC-ND 4.0 International license .

Star anise (Illicium verum), a valuable spice tree, faces significant threats from fungal diseases, particularly Alternaria leaf spot. This study investigates the potential of a soil-derived actinomycete strain, YG-5, as a biocontrol agent against Alternaria tenuissima, the causative pathogen on Alternaria leaf spot in star anise. Through comprehensive morphology, physiology, biochemistry, and genetic analyses, we identified the isolate as Streptomyces sp. YG-5. The strain exhibited broad-spectrum antimicrobial activity against several plant pathogens, with inhibition rates ranging between 36.47 to 80.34%. We systematically optimized the fermentation conditions for YG-5, including medium composition and cultivation parameters. The optimized process resulted in an 89.56% inhibition rate against A. tenuissima, a 14.72% improvement over non-optimized conditions. Notably, the antimicrobial compounds produced by YG-5 demonstrated stability across various temperatures, pH levels, and UV irradiation. In vivo efficacy trials showed promising results, with YG-5 fermentation broth reducing Alternaria leaf spot incidence on star anise leaves by 56.95%. These findings suggest that Streptomyces sp. YG-5 holds significant potential as a biocontrol agent against Alternaria leaf spot in star anise cultivation, offering a sustainable approach to disease management in this valuable crop.

Wearable devices can provide timely, user-friendly, non- or minimally invasive, and continuous monitoring of human health. Recently, multidisciplinary scientific communities have made significant progress regarding fully integrated wearable devices such as sweat wearable sensors, saliva sensors, and wound sensors. However, the translation of these wearables into markets has been slow due to several reasons associated with the poor system-level performance of integrated wearables. The wearability consideration for wearable devices compromises many properties of the wearables. Besides, the limited power capacity of wearables hinders continuous monitoring for extended duration. Furthermore, peak-power operations for intensive computations can quickly create thermal issues in the compact form factor that interfere with wearability and sensor operations. Moreover, wearable devices are constantly subjected to environmental, mechanical, chemical, and electrical interferences and variables that can invalidate the collected data. This generates the need for sophisticated data analytics to contextually identify, include, and exclude data points per multisensor fusion to enable accurate data interpretation. This review synthesizes the challenges surrounding the wearable device integration from three aspects in terms of hardware, energy, and data, focuses on a discussion about hybrid integration of wearable devices, and seeks to provide comprehensive guidance for designing fully functional and stable wearable devices.

Patchouli (Pogostemon cablin (Blanco) Benth) is an important medicinal and aromatic plant widely cultivated in China, India, and other Southeast Asian countries. It is renowned for its diverse applications in traditional medicine and its detoxification, antibacterial, anti-inflammatory, and other pharmacological properties (Wu et al. 2016; Fang et al. 2022). In May 2023, a severe leaf spot disease was observed on Pogostemon cablin plants grown in most plantations in Yulin, Guangxi, China (22°26'N; 109°83'E), with over 50% incidence rate. Symptoms began as small, circular, brown spots on leaves, enlarging with yellow halos. Lesions expanded into irregular shapes with necrotic centers. Advanced stages showed extensive yellowing, browning, and leaf senescence. A total of 20 symptomatic plants were sampled from 5 different locations within the detected area, with 4 plants sampled per location. To isolate the pathogen, 20 affected leaves were collected from these plants and preliminarily washed with sterile distilled water (SDW). Five small tissue pieces (5×5 mm) were excised from the lesion edge of each leaf, surface-disinfected with 75% ethanol and 1% NaClO, rinsed thrice with SDW, and placed on potato dextrose agar (PDA) at 28 °C in darkness for 7 days. Out of these, 18 plants (90%) yield fungal isolate with recurrent and similar morphological characteristics. Four representative isolates (X5-1-1, X5-1-3, X5-1-5, and X5-1-7) were selected for further analysis. On PDA, colonies were initially white, gradually turning black on the surface, with light yellow on the reverse side of the plate. Conidia were brown to black, globose, rough-walled, and 2.6 to 5.2 µm in diameter. Conidial heads were brown-black, and conidiophores were smooth and hyaline. Morphological characteristics matched those of Aspergillus sp. (Guo et al. 2017). For molecular identification, the internal transcribed spacer (ITS) region and the β-tubulin (TUB) gene of all four isolates were sequenced (Lim et al. 2019). All four isolates (X5-1-1, X5-1-3, X5-1-5, and X5-1-7) showed consistent morphological characteristics and 100% identical ITS and TUB sequences. Representative sequences from isolate X5-1-5 were submitted to GenBank (ITS: PP789632; TUB: PP798205). The obtained ITS and TUB sequences showed 99% similarity to Aspergillus tubingensis (ITS: OP737633; TUB: MG991377). Based on morphological and molecular analyses, the fungus was identified as A. tubingensis (Palmer et al. 2019). For pathogenicity tests, a spore suspension (1 × 10^6 conidia/mL) was prepared from 7-day-old cultures of A. tubingensis grown on PDA. The suspension was sprayed onto leaves of 10 healthy Pogostemon cablin plants until runoff. Control plants were sprayed with SDW. All plants were kept in a controlled greenhouse (12/12h light/dark, 25 ± 2 °C, 90% humidity). After 7 d, symptoms identical to those observed in the field developed on all pathogen inoculated plants, while control plants remained asymptomatic. The fungus was successfully re-isolated from infected leaves in three successive trials, fulfilling Koch's postulates. Notably, A. tubingensis has previously been reported causing field diseases on strawberry in California, Jatropha curcas and Helleborus species in China (Palmer et al. 2019; Guo et al. 2017, Liaquat et al. 2019), and vine canker on table grape in Italy (Vitale et al. 2012). To our knowledge, this is the first report of A. tubingensis causing leaf spot on Pogostemon cablin in China. This finding provides a foundation for further investigate into the biology, epidemiology, and management of this disease.

In this work, Ge 2 Sb 2 Te 5 (GST) thin films are irradiated by a 1064 nm pulsed laser heat treatment system with different beam profiles. The surface effects induced by different laser conditions are studied systematically by atomic force microscope, spectroscopic ellipsometry, and Raman spectroscopy. It is found that a top-hat beam profile with uniform intensity distribution demonstrates the advantages of a non-destructive and homogeneous surface, which is critical for large-scale processing uniformity. The threshold laser fluence for the amorphization process is predicted by simulation and further proved by the laser irradiation experiment to be 27.9 mJ/cm 2 at 1 ns pulse width. We further show that modulation of complex refractive indices of GST thin films can be achieved with different duty ratios (spatial ratio of amorphization part) from 0% to 100%. Our approach paves the way for the precise control of the optical properties of PCMs in emerging optical applications such as photonic switches, optical memories, and all-optical neural networks.

Competitive‐learning‐based spiking neural networks are capable of rapid, highly accurate pattern recognition with minimal data through denoising mechanisms provide by adaptive interneuron inhibition. However, hardware implementations of such networks are currently area‐inefficient due to the high device count require to execute dual excitatory‐inhibitory synapses. To mitigate this, n‐ / p‐ reconfigurable tungsten diselenide memtransistors is introduced that can execute excitatory and inhibitory synapses in a highly compact bio‐inspired feature extractor hardware architecture. The reconfigurability is realized through a dual mode memory device with a flash‐memory‐like floating‐gate for n‐ / p‐ programing and a memristor‐like selenium vacancy‐based resistive switching that varies in memristive output with majority carrier modulation. Through a device‐system codesign, an effective 27% device count reduction in the peripheral circuits is achieved , which ameliorates circuit component congestion and circuit complexity. Compared to the prevalent winner‐takes‐all approach, the proposed machine learning with adaptive interneuron inhibition achieves high‐accuracy convergence with up to five times smaller training dataset. This accelerated learning can potentially enable edge‐artificial intelligence (AI) processors capable of ultra‐low‐energy training with limited data.

With high device integration density and evolving sophisticated device structures in semiconductor chips, detecting defects becomes elusive and complex. Conventionally, machine learning (ML)-guided failure analysis is performed with offline batch mode training. However, the occurrence of new types of failures or changes in the data distribution demands retraining the model. During the manufacturing process, detecting defects in a single-pass online fashion is more challenging and favoured. This paper focuses on novel quantile online learning for semiconductor failure analysis. The proposed method is applied to semiconductor device-level defects: FinFET bridge defect, GAA-FET bridge defect, GAA-FET dislocation defect, and a public database: SECOM. From the obtained results, we observed that the proposed method is able to perform better than the existing methods. Our proposed method achieved an overall accuracy of 86.66% and compared with the second-best existing method it improves 15.50% on the GAA-FET dislocation defect dataset.

In this article, we demonstrate a low-thermal budget defect-engineered process to achieve top-gated (TG) oxide–semiconductor ferroelectric field-effect transistors (FeFETs). The demonstrated TG FeFETs, with the channel length scaled down to 40 nm, exhibit a highly stabilized ferroelectric memory window (MW) of 2 V and a high current ON/ OFF ratio of $10^{{6}}$ . This is achieved by an engineered InGaZnOx (IGZO) and InSnOx (ITO) heterojunction channel that produces the defect self-compensation effect to passivate the intrinsic oxygen-deficient defects, existing in the indium-gallium-zinc-oxide (IGZO) channel interface and bulk. Effective interface/bulk defects passivation with good control of defect-induced channel carrier concentration has been notoriously difficult to achieve. Hence, realizing performant TG oxide-based FeFETs with back-end-of-line (BEOL) thermal budget constraints remains a fundamental challenge. Our study shows that heterojunction channel engineering on FETs and FeFETs can be a reliable solution to overcome this challenge. With such a technique, we can now enable double-gated (DG) ITO–IGZO FeFET and FETs. Such devices can enable BEOL-compatible reconfigurable nonvolatile logic switches that provide extremely low off-state leakage, high switch conductance ratio, and memory read-write disturb-free features.

The insect pathogenic fungus, Ascosphaera apis, is the causative agent of honeybee chalk brood disease. Amylases are secreted by many plant pathogenic fungi to access host nutrients through the metabolism of starch, and the identification of new amylases can have important biotechnological applications. Production of amylase by A. apis in submerged culture was optimized using the response surface method (RSM). Media composition was modeled using Box–Behnken design (BBD) at three levels of three variables, and the model was experimentally validated to predict amylase activity (R2 = 0.9528). Amylase activity was highest (45.28 ± 1.16 U/mL, mean ± SE) in media composed of 46 g/L maltose and1.51 g/L CaCl2 at a pH of 6.6, where total activity was ~11-fold greater as compared to standard basal media. The enzyme was purified to homogeneity with a 2.5% yield and 14-fold purification. The purified enzyme had a molecular weight of 75 kDa and was thermostable and active in a broad pH range (> 80% activity at a pH range of 7–10), with optimal activity at 55 °C and pH = 7.5. Kinetic analyses revealed a Km of 6.22 mmol/L and a Vmax of 4.21 μmol/mL·min using soluble starch as the substrate. Activity was significantly stimulated by Fe2+ and completely inhibited by Cu2+, Mn2+, and Ba2+ (10 mM). Ethanol and chloroform (10% v/v) also caused significant levels of inhibition. The purified amylase essentially exhibited activity only on hydrolyzed soluble starch, producing mainly glucose and maltose, indicating that it is an endo-amylase (α-amylase). Amylase activity peaked at 99.38 U/mL fermented in a 3.7 L-bioreactor (2.15-fold greater than what was observed in flask cultures). These data provide a strategy for optimizing the production of enzymes from fungi and provide insight into the α-amylase of A. apis.

Humans rely increasingly on sensors to address grand challenges and to improve quality of life in the era of digitalization and big data. For ubiquitous sensing, flexible sensors are developed to overcome the limitations of conventional rigid counterparts. Despite rapid advancement in bench-side research over the last decade, the market adoption of flexible sensors remains limited. To ease and to expedite their deployment, here, we identify bottlenecks hindering the maturation of flexible sensors and propose promising solutions. We first analyze challenges in achieving satisfactory sensing performance for real-world applications and then summarize issues in compatible sensor-biology interfaces, followed by brief discussions on powering and connecting sensor networks. Issues en route to commercialization and for sustainable growth of the sector are also analyzed, highlighting environmental concerns and emphasizing nontechnical issues such as business, regulatory, and ethical considerations. Additionally, we look at future intelligent flexible sensors. In proposing a comprehensive roadmap, we hope to steer research efforts towards common goals and to guide coordinated development strategies from disparate communities. Through such collaborative efforts, scientific breakthroughs can be made sooner and capitalized for the betterment of humanity.

Little is known concerning terpenoids produced by members of the fungal order Ophiostomales, with the member Harringtonia lauricola having the unique lifestyle of being a beetle symbiont but potentially devastating tree pathogen. Nine known terpenoids, including six labdane diterpenoids (1–6) and three hopane triterpenes (7–9), were isolated from H. lauricola ethyl acetate (EtOAc) extracts for the first time. All compounds were tested for various in vitro bioactivities. Six compounds, 2, 4, 5, 6, 7, and 9, are described functionally. Compounds 2, 4, 5, and 9 expressed potent antiproliferative activity against the MCF-7, HepG2 and A549 cancer cell lines, with half-maximal inhibitory concentrations (IC50s) ~12.54–26.06 μM. Antimicrobial activity bioassays revealed that compounds 4, 5, and 9 exhibited substantial effects against Gram-negative bacteria (Escherichia coli and Ralstonia solanacearum) with minimum inhibitory concentration (MIC) values between 3.13 and 12.50 μg/mL. Little activity was seen towards Gram-positive bacteria for any of the compounds, whereas compounds 2, 4, 7, and 9 expressed antifungal activities (Fusarium oxysporum) with MIC values ranging from 6.25 to 25.00 μg/mL. Compounds 4, 5, and 9 also displayed free radical scavenging abilities towards 2,2-diphenyl-1-picrylhydrazyl (DPPH) and superoxide (O2−), with IC50 values of compounds 2, 4, and 6 ~3.45–14.04 μg/mL and 22.87–53.31 μg/mL towards DPPH and O2−, respectively. These data provide an insight into the biopharmaceutical potential of terpenoids from this group of fungal insect symbionts and plant pathogens.

In this work, we elucidate the fundamental bias stress reliability mechanism in oxide-semiconductor devices and provided guidelines to improve interface/bulk-induced V TH degradation. We provide further insights into the defect-self compensation effect for the bilayer ITO-IGZO channel. Specifically, how our process approach led to effective passivation of channel defects such as negative-U defects, and ionized-oxygen-vacancy defects. With bilayer ITO-IGZO, we demonstrated 10x negative/positive bias stress (NBS/PBS), and 4x negative bias illumination stress (NBIS) improvement against the conventional mono-IGZO devices. Furthermore, under a low-thermal budget constraint, we implemented a sacrificial replacement gate stress memorization technique to enhance the ferroelectric phase to enable a double-gated (DG) IGZO FeFET. Our reliability-optimized DG ITO-IGZO FeFETs exhibit an enhanced memory window (MW) of 1.7V, excellent memory-write endurance of 10 7 cycles, outstanding memory retention with high I ON /I OFF of 10 6 after 10 4 s, record-low NBS/PNS V TH shift of 30mV, and NBIS V TH shift of 110mV after stress time of 1000s. These devices set a new oxide thin-film transistor (TFT) reliability record making major strides toward highly reliable BEOL logic and memory switches.

Star anise (Illicium verum) is an important economic and medical plant widely cultivated in Guangxi province, China. Its fruit can be used as spice and medicine (Wang et al. 2011). In recent years, anthracnose led to a serious decline in the production of star anise in Guangxi. In 2021, a survey conducted in CenwangLaoshan Reserve of Guangxi (24°21'N; 106°27'E) showed that the 2500 ha planting area had disease incidence greater than 80%. The leaf symptoms initially appeared as small spots, then expanded to round spots, finally becoming withered with grayish-white centers, surrounded by dark brown margins. Sometimes, small black acervuli were observed in the later stage. To explore the pathogen, infected leaves were collected and cut into small pieces (about 5 mm2) from the edge of the lesion, disinfected with 75% ethanol for 10 s, 1% NaClO for 1 min, washed with sterilized water and incubated on potato dextrose agar (PDA) plates at 28 °C in the dark. Ten single-spore isolates were obtained from the cultures. After 7 days on PDA at 28 °C, the colonies of 7 isolates were white with abundant aerial hyphae, gray-black with white-gray margins, and the other 3 isolates were light gray on the upper surface, and pink or orange on the underside. Representative isolates BS3-4 and BS3-1 were selected from 3 isolates and 7 isolates, respectively. Conidia of BS3-4 and BS3-1 were both hyaline, cylindrical, aseptate, smooth, apex obtuse, base truncate, and no significant differences (P > 0.05) in size between BS3-1 (13.22 to 5.38 × 3.89 to 1.99 μm) (n = 50) and BS3-4 (12.04 to 4.34 × 3.48 to 1.64 μm) (n = 50). These morphological characteristics were consistent with the Colletotrichum ssp. (Damm et al. 2012). The species identification of BS3-4 and BS3-1 was performed based on DNA sequence analysis. Genomic DNA was extracted as a template. Partial sequences of the rDNA internal transcribed spacer (ITS), actin gene (ACT), β-tubulin2 (TUB2) and glyceraldehyde-3-phosphate dehydrogenase (GAPDH) were amplified and sequenced (Weir et al. 2012). The sequences were deposited in GenBank (ITS:OQ062642-43; ACT:OQ067614-15; GAPDH:OQ067616-17;TUB2：OQ067618-19). Based on the concatenated sequences of the 4 genes (ITS-ACT- GAPDH -TUB2) of BS3-4 and BS3-1 as well as sequences of other Colletotrichum spp. obtained from GenBank, the Maximum likelihood (ML) tree which produced with IQ-TREE (Minh et al. 2020) revealed that the isolate BS3-1 was Colletotrichum horii, and BS3-4 was Colletotrichum fioriniae. Pathogenicity was confirmed on healthy leaves of 1-year-old star anise seedlings (cultivar Dahong), and the leaves were wounded by sterilized toothpicks, and were inoculated with 10 µl of conidial suspensions of BS3-1 and BS3-4 (106 conidia/ml). Control seedlings were inoculated with sterilized distilled water. Five leaves per plant and 3 plants per treatment were selected. All inoculated seedlings were maintained in the greenhouse (12/12h light/dark, 25 ± 2℃, 90% relative humidity). Wound sites inoculated with BS3-1 and BS3-4 both turned greenish-brown after 2 days and then turned light brown with water-soaked spots. Black (BS3-1) or orange (BS3-4) dots of acervuli developed after 6 days. The lesion diameter of BS3-1 (14.4 mm) was larger than that of BS3-4 (8.1 mm). No symptoms were observed on controls. BS3-1 and BS3-4 were re-isolated from inoculated leaves, fulfilling Koch's postulates. Anthracnose of star anise caused by C.horii has been reported in China (Liao et al. 2017). However, to our knowledge, this is the first report of C.fioriniae infecting star anise in China. Accurate pathogen identification in this study could provide a reference for the control of anthracnose on star anise.

A ferroelectric field-effect transistor (FeFET), capable of logic and memory functionalities in a single device, is a promising three-terminal memtransistor that enables high-performance in-memory computing for non Von Neumann architectures. Among all HfO2-based ferroelectric materials, HfZrO2 (HZO) has attracted the most attention due to the low process temperature of <= 500 degrees C; however, it has relatively weak polarization. Many prior works claimed that the way to improve HZO-based FeFET characteristics is to enhance HZO ferroelectric properties, while they did not account for the fundamental compromise on dielectric breakdown strength (BDS), transistor ON/OFF current (ION/IOFF) ratio, and memory window (MW) due to the enhanced polarization. In this work, we propose an approach for controlling the ferroelectric orthorhombic phase (O phase) and the corresponding polarization in optimal value by engineering both the surface morphology and stress of HZO layer by a thermal expansion mismatch with a TiN/W stacked capping layer, to improve the BDS, ION/IOFF ratio, and MW. Through electrode surface optimization and stress memorization we achieved an 18% HZO ferroelectricity increase with a high BDS value of <= 4.8 MV/cm. Our optimized FeFET shows good electrical characteristics and supports operation in an identical pulse programming (IPP) mode, showing good potentiation and depression nonlinearity (-0.84 and -2.04) with an asymmetry factor of 1.2. A simulation based on the proposed FeFET array demonstrates the high potential of application in an artificial neural network (ANN).

微生物实验是高校生物类各专业的一门基础课程,是培养学生实际应用能力的重要途径之一.针对现有教学中所存在的不足,有效的实验室管理和实验教学改革是提高实验教学质量的必由之路.为了更好地提升微生物学实验教学课程,从教学方式、设备培训和实验室管理等方面进行改革,进一步培养学生学习的积极性,提高教学质量.

Batrachochytrium dendrobatidis (Bd), which causes chytridiomycosis, mainly infects Anura and Caudata but is poorly known in Gymnophiona. We conducted a survey of Bd in the Yunnan caecilian (Ichthyophis bannanicus) and found that 6 of 71 samples (8.4%) tested positive for Bd. To our knowledge, this is the first detection of Bd in wild I. bannanicus.

If Si CMOS for massive M3D is difficult due to need for high-thermal-budget processes, are there solutions that are beyond Si? In this article, we discuss two low-thermal-budget approaches: Oxide Semiconductor and 2D Materials for M3D integration. By reviewing some of our recent work with IGZO-based transistors and memories, followed by our investigation of the 2D material opportunities for 3D memories, we highlight the need for new low-thermal-budget additive techniques for heterogenous multi-material integration as well as low-temperature material modification. Given the unlikelihood of “perfect materials”, new system architecture-material-device co-design intervention will be essential to capitalize on the specific trade-offs of the components.